Used Paul O Abbe Process Equipment
Stock No.:
10715045IN STOCK and New- Paul O. Abbe Model RB-195 Ribbon Blender.
NEW & IN STOCK- Paul O. Abbe Model RB-195 Ribbon Blender. In -Stock .195 Cubic Foot working capacity. 220 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 56.7" wide x 118.2" long x 62.6" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 60 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 29 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 4.7" wide x 19.7" flush air operated plug valve. Discharge housing is approximate 20.5" wide x 28.4" long. Approximately 4" discharge height. Approximate weight 11,660 pounds. Approximate overall dimensions: 76.4" wide x 183" long x 93.8" high. Controls are available upon request.
MFR: Paul O Abbe
Stock No.:
52106002Unused Paul O. Abbe OPCM-67 Ceramic Ball Mill – 250L, 3 HP, 34 RPM
Unused- Paul O Abbe One Piece Ceramic Ball Mill, Model OPCM-67. 250 liter, 19% alumina content. Approximate 24.8" diameter x 31.9" long. 6.7" inlet/outlet, 39" discharge height from the top of the base plate to hatch. Driven by a 3 hp direct shaft mounted motor. 34 rpm maximum vessel rotation. Mounted on painted carbon steel stands on a painted carbon steel base. Serial# 196635OPCM.
MFR: Paul O Abbe
Stock No.:
10715049IN STOCK and NEW- Paul O Abbe Model RB-265 Ribbon Blender
NEW & IN STOCK- Paul O. Abbe Model RB-265 Ribbon Blender. In -Stock .265 Cubic Foot working capacity. 289 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 63" wide x 130" long x 67.8" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 75 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 26 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 4.7" wide x 27.6" flush air operated plug valve. Discharge housing is approximate 20.5" wide x 36.2" long. Approximately 4" discharge height. Approximate weight 14,960 pounds. Approximate overall dimensions: 81" wide x 206.5" long x 94.8" high. Controls are available upon request.
MFR: Paul O Abbe
Stock No.:
52710004Pre-Owned Paul O Abbe Jar Rolling Mill – 3” x 60” Rolls, 86-258 RPM
Used- Paul O Abbe Single Tier Jar Rolling Mill Enclosure, Model JRM. 3" Diameter x 60" wide rolls. Roll speed: 86 to 258 rpm, set rolls at 169 rpm. Approximate 3/4hp, 3/60/230/460 volt, motor. Sound attenuated enclosure. Mounted on fork-liftable base. Serial# A35796. Capable of being two-tier. ***THIS MACHINE IS OFFERED FOR RENTAL. ASK AN AARON EQUIPMENT PROFESSIONAL FOR MORE INFORMATION***
MFR: Paul O Abbe
Stock No.:
10715051IN STOCK & NEW- Paul O Abbe, Model RB-315 Ribbon Blender
NEW- Paul O. Abbe, Model RB-315 Ribbon Blender. 315 Cubic Foot working capacity. 356 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 65.4" wide x 141.8" long x 73.3" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 75 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 20 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 5.5" wide x 27.6" flush air operated plug valve. Discharge housing is approximate 20.5" wide x 36.2" long. Approximately 4" discharge height. Approximate weight 19,580 pounds. Approximate overall dimensions: 87.8" wide x 218.4" long x 100.4" high.Controls are available upon request.
MFR: Paul O Abbe
Stock No.:
54186002Used Paul O. Abbe RB-315 Ribbon Blender – 315 Cu Ft Stainless Steel Food Grade Industrial Mixer
Used Paul O. Abbe RB-315 Ribbon Blender 315 Cu Ft Stainless Steel Food Grade Industrial Mixer. 356 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 65.4" wide x 141.8" long x 73.3" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 75 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 20 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 5.5" wide x 27.6" flush air operated plug valve. Discharge housing is approximate 20.5" wide x 36.2" long. Approximately 4" discharge height. Approximate weight 19,580 pounds. Approximate overall dimensions: 87.8" wide x 218.4" long x 100.4" high.
MFR: Paul O Abbe
Stock No.:
10715046IN STOCK& NEW- Paul O. Abbe, Model RB-35 Ribbon Blender.
NEW & IN STOCK- Paul O. Abbe, Model RB-35 Ribbon Blender. In -Stock .35 Cubic Foot working capacity. 39 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 33.4" wide x 59.1" long x 37.4" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 25 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 42 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 19.7" wide x 31.5" long. Approximate 4.7" wide x 14.2" flush air operated plug valve. Discharge housing is approximate 18.5" wide x 24" long. Approximately 24" discharge height. Approximate weight 2,860 pounds. Approximate overall dimensions: 52.7" wide x 107.5" long x 84.3" high. Controls are available upon request. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.
MFR: Paul O Abbe
Stock No.:
53959001Used Paul O Abbe Rota-Cone Vacuum Dryer, 240 Cu Ft Capacity – Model 108 RCVD, Stainless Steel, Fully Refurbished
Used- Paul O Abbe Rota-Cone Vacuum Dryer, Model 108 RCVD. 304 stainless steel. 240 cubic feet working capacity, 365 cubic feet total capacity. #4 Polished internal 108 diameter, rated 30 psi at 500 deg F to full vacuum. Carbon steel jacket rated 40 psi at 500 deg F coincident with full vacuum on internal. 20" diameter top port with cover, 12" center bottom outlet. Driven by a 10 hp, 3/60/230/460 volt gear motor with brake, ratio 82.6 to 1. Approximate 4 rpm cone. Mounted on carbon steel stands. Includes Wintek Vacuum Pump Skid, Mokon Chiller and Mokon hot water circulating unit. 2016 refurbishment included: General clean up; New Vacuum Line; New Oil Feed Box; New Drive & Idler Side Bearings; New Gear Wheel; New Spray Line; New Pinion Gear; New Gear Guard; New Valve w/ Gear Wheel Operator; New Gearmotor w/ Brake; Polished product contact areas to 180 Grit. 260" L x 120" W x 170" H. Approx. 18,000 lbs.
MFR: Paul O Abbe
Stock No.:
10715053In STOCK AND New- Paul O. Abbe, Model RB-375 Ribbon Blender
NEW & IN STOCK- Paul O. Abbe, Model RB-375 Ribbon Blender.In -Stock . 375 Cubic Foot working capacity. 441 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 67.7" wide x 157.5" long x 78.8" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 75 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 20 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 5.5" wide x 27.6" flush air operated plug valve. Discharge housing is approximate 20.5" wide x 36.2" long. Approximately 4" discharge height. Approximate weight 20,944 pounds. Approximate overall dimensions: 91.9" wide x 237.1" long x 104.7" high. Controls are available upon request.
MFR: Paul O Abbe
Stock No.:
10715035IN STOCK & NEW- Paul O. Abbe Model RB-65 Ribbon Blender.
NEW & IN STOCK- Paul O. Abbe Model RB-65 Ribbon Blender. In -Stock .65 Cubic Foot working capacity. 72 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 39.4" wide x 78.8" long x 44.1" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 30 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 36 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 4.7" wide x 14.2" flush air operated plug valve. Discharge housing is approximate 18.5" wide x 24" long. Approximately 23" discharge height. Approximate weight 5,060 pounds. Approximate overall dimensions: 60.6" wide x 131.4" long x 90.3" high. Controls are available upon request.
MFR: Paul O Abbe
Stock No.:
52106001New Paul O. Abbe Model RCVD-9 Body Only
New/Unused - Paul O. Abbe Model RCVD-9 Body Only. 8.8 Cubic Foot Working Capacity. Type 304 SS Contact Surface. 36" Diameter Body. 180 Grit Polish, 32 Ra. 14.7 psig Non-Code Jacket. 2" Chloride Free Rock Wool Insulation with 304 SS Welded Shroud, Glass Bead Blasted. Vacuum Line with RTD for Sensing Product Temperature, No Readout. 8" Loading Cover. 6" Manual Butterfly Valve. 1 HP Drive Motor, TEFC. Rated up to 90 lbs/ft3. *** We can complete this vessel with New Stands in about 8 Weeks. We can also offer this with the following options: Higher HP for minerals and Powdered Metals, Liquid Spray Bar, Gas Purge, Product Sampler, 304 SS Legs, XP Motor, Positioning System and Controls , Nema -12, Nema 4, Nema 4X SS and Nema 7&9***
MFR: Paul O Abbe
Stock No.:
54444001Unused Paul O. Abbe BM-223 Ball Mill – Stainless Steel Industrial Grinding Mill
Unused Model BM-223 all-stainless-steel ball mill featuring a 2 tapered cylinder for full discharge and a split, hinged clamshell dry discharge housing. The cylinder measures 40 inches in diameter by 44 inches long inside the shell, with an internal finish of 32 RA (180 grit polish) and a shell thickness of 5/8 inch. The cylinder and product-contact surfaces are constructed of 304 stainless steel. Welded lifter bars terminate 1.5 inches from the ends, with welds laid down and ground to a minimum 1/4 inch radius and finished pit-free. The total mill volume is 32 ft (234 gallons), with a dry working volume of 8 ft (25% of total). The unit includes a 13.25 inch by 14.75 inch rectangular cover hatch frame welded into the side of the mill, a stainless steel grinding cover contoured to the inside radius, and a stainless steel dry discharge cover with 0.25 inch slots. The dry discharge housing fully encloses the mill cylinder to capture and direct solids to a chute or hopper, utilizing the patented 2 taper for full discharge (US Patent 10,086,379, Oct 2, 2018). The clamshell housing design incorporates stainless counterweights and stainless steel construction, with a nominal 60 chute/hopper below the mill and a 12 inch square bottom opening. Housing product-contact surfaces are 304 stainless steel with a 32 RA (180 grit polish) finish. Discharge height is 48 inches from hatch to floor. Additional features include a sliding UHMW cover on top of the housing. The mill drive is an SEW hollow bore, 20 HP TEFC motor rated for 230/460 volt, 3-phase, 60 Hz operation, providing a nominal cylinder speed of 24 RPM. The system is supported by two welded A" frame stands with box-style extensions for added height, constructed of carbon steel and coated with Sherwin-Williams Tile Clad epoxy. Overall dimensions are 138 inches high by 105 inches long by 64 inches deep.
MFR: Paul O Abbe