Used Davis Standard Process Equipment
Stock No.:
10755179Used Davis Standard 1.5" Extruder – Model 150IN DS-20, 24:1 L/D, Vented Barrel, 50 HP Gearbox
Used- Davis Standard 1.5" Extruder, Model 150IN DS-20. 24:1 L/D vented barrel at a 42" centerline. Davis Standard 6.53:1 gearbox rated for 50 HP with a service factor of 1.25 for a 152 RPM screw speed. Gearbox was manufactured in 1998. Non-tagged motor is driven by a Reliance model GV3000 A/C drive. Includes unitized temperature control panel and 4-hole strand die on barrel. Year 1984.
MFR: Davis Standard
Stock No.:
10755162Used Davis Standard 10" Extruder, Model 100TH100D. 38:1 L/D ratio; (8) zone electrically heated, water cooled
Used- Davis Standard 10" Extruder, Model 100TH100D. 38:1 L/D ratio; (8) zone electrically heated, water cooled and non-vented barrel at nominal 44" center-line. 15.08:1 Gearbox reduction ratio; Rated at 1800 HP at a service factor of 1.5; Gearbox currently set to be dual direct driven in back of the gearbox. Last driven by two (2) 700 HP D/C motors; Liquid cooling system with heat exchanger for gearbox protection; Trendelkamp screen changer w/ stand mounted on the extruder discharge. Temperature control panel and drives included. Motors available at additional cost. Temperature controllers not included. Serial# L3201. Built 1991. Last used in the extrusion of biaxially oriented PP film.
MFR: Davis Standard
Stock No.:
54506008Used & Reconditioned Davis-Standard Thermatic 60IN60 6" Single Screw Extruder – 400 HP, 24:1 L/D, Thermatic Clamp
Used & Reconditioned Davis-Standard Thermatic 60IN60 6" Single Screw Extruder 400 HP, 24:1 L/D, Thermatic Clamp. 24:1 L/D ratio, water-cooled barrel, integrated water reservoir, recirculation pump, and heat exchanger. Equipped with a 17.21:1 gearbox rated for 424 HP capacity with a 1.5 service factor, powered by a new 400 HP TECO AC motor (Model EPS4004, 1,800 RPM, 449TX frame) and new TECO AC drive (Model EQ7-4450-C). Includes five barrel heating zones and six die heating zones with new Novus temperature controllers and amp gauges, swing-arm operator station with speed pod, pressure and screw speed gauges, and a 42" centerline height. Fitted with a Thermatic clamp and barrier flight screw; screw and barrel are within serviceable tolerances. Heater bands have been electrically tested, barrel plumbing and heat exchangers have been flow checked, and five new Red Hat solenoid valves have been installed. Approximate overall dimensions are 216" L x 80" W x 90" H. Originally built 2004.
MFR: Davis Standard
Stock No.:
54506009Used Davis-Standard 60IN60TPIH 6" Single Screw Extruder – 34:1 L/D, 400 HP, Vented Barrel with ABB Drive
Used Davis-Standard 60IN60TPIH 6" Single Screw Extruder 34:1 L/D, 400 HP, Vented Barrel with ABB Drive. Features a 34:1 L/D ratio with a water-cooled, vented barrel incorporating six cooling zones; vent is located approximately 130" from the center of the feed throat and is currently plugged. Cooling system includes a 1/2 HP recirculation pump, heat exchanger, and 32" x 24" x 12" water reservoir. Driven by a 400 HP WEG AC motor (1,790 RPM) with ABB AC drive and a Davis-Standard Model 60IN60TPIH gearbox featuring a 17.2:1 ratio and rated for 526 HP with a 1.5 service factor. Temperature controls include six-barrel zone Solo 4896 controllers and seven die zone Omron E5EC controllers. Operator controls feature a speed pod with screw RPM, motor load percentage, and pressure transducer gauges. Includes hopper, 42" centerline height, and serial number PT238. Approximate footprint is 25' L x 8' W. Built 1994.
MFR: Davis Standard
Stock No.:
54506010Used & Reconditioned Davis-Standard 600S Thermatic 6" Single Screw Extruder – 300 HP, 30:1 L/D, Reconditioned in 2025
Used & Reconditioned Davis-Standard 600S Thermatic 6" Single Screw Extruder 300 HP, 30:1 L/D, Reconditioned in 2025. Features a 30:1 L/D ratio with a PE/PP screw and a 17.21:1 gearbox ratio. Powered by a new 300 HP Westinghouse AC motor with a new WEG AC inverter drive. Equipped with a refurbished 10-zone control panel consisting of six barrel heating zones and four downstream zones, all fitted with new Eurotherm 3216 temperature controllers. Gearbox has been rebuilt with all internal bearings replaced except the thrust bearing. Serial No. F-9731, S.O. 901180. Electrical requirements are 460 Volt, 3 Phase, 60 Hz. Approximate overall dimensions are 242" L x 74" W x 102" H with an estimated weight of 23,000 lbs. Originally built in 1998, reconditioned in 2025.
MFR: Davis Standard
Stock No.:
10755163Used Davis Standard 9" Extruder, Model 80IN80HT – 32:1 L/D, 900 HP Motor, Built 2001
Used- Davis Standard 9" Extruder, Model 80IN80HT. 32:1 L/D ratio; (7) zone electrically heated, water cooled (closed loop), and vented barrel at a 44" center-line; 10.15:1 Gearbox reduction ratio; Gearbox rated at 1080 HP at a service factor of 1.5; Gearbox is direct driven in a wrap-around manner by a 900 HP Reliance Super RPM D/C motor; Liquid cooling system with heat exchanger for gearbox protection; 16" x 9 1/2" on center feed throat entrance; PSI continuous screen changer w/ stand is mounted on the extruder discharge. 16" x 9.5" feed throat with magnet; 52,000 lbs. extruder weight; 1,000 lbs. motor weight. Rare opportunity to purchase an extruder of this size. Per Davis Standard the thrust bearing rating is actually 1,468,000 pounds or 665,874 kgs. Unit was miss tagged at the factory. Serial# AA454. Built 2001. Last used in the extrusion of PP sheet. SCR and temperature control panel not included.
MFR: Davis Standard