Used Ribbon Blenders

Stock# 52248001

Used-Griffith 1500 lb Stainless Steel Dual Shaft Ribbon Blender, Model G-37.5/2. The blender sits on 4- 5,000 lb hermetically sealed load cells. Open top with stainless steel safety grates, Dual end bottom hydraulic discharge doors. Driven by (2) 7.5 HP, 3/60/230-460 volt motors. Last use to mix ground beef and pork for hotdog and sausage production.

Stock# 51100002

Used- JH Day Ribbon Blender, Stainless Steel. Approximate 1 Cubic Feet. Jacket rated for 45 psig at 293 degree F. 1-1/2 HP Main Motor. Year 1987. Approximate 4" outlet. Last used in a Breath Mint application.

Stock# 11585071

Used-JH Day 5 Cubic Foot (approximately) Stainless Steel Double Ribbon Blender. Approximately 16" wide X 38" long X 19" deep. Center bottom discharge. Approximately 1.5 hp Motor and reducer. Top hinged cover. Mounted on legs.

Stock# 11585073

Used-10 Cubic Foot (approx.) Stainless Steel Ribbon Blender. Double ribbon. Stainless steel contacts. Carbon steel jacket. Approximately 20" wide X 60" long X 24" deep. Built by Howes. 4" Center bottom outlet with manual valve. Multi Section Hinged lid with counter weights. 26" clearance from bottom outlet to the floor.

Stock# 10715050

New- Paul O. Abbe, Model RB-10 Ribbon Blender. 10 Cubic Foot working capacity. 11 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 22.1" wide x 38.6" long x 25" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 5 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 66 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 11.8" wide x 19.7" long. Approximate 3.2" wide x 9.9" flush air operated plug valve. Discharge housing is approximate 15.4" wide x 19.3" long. Approximately 35.5" discharge height. Approximate weight 1,320 pounds. Approximate overall dimensions: 36.4" wide x 76.4" long x 81.4" high. Controls are available upon request.

Stock# 51647001

Used- Toronto Coppersmithing Single Spiral Ribbon Blender. Approximately 14 cubic foot capacity. 304 Stainless Steel Contact Areas. Non-jacketed trough approximately 48" Long x 24" Wide x 28" Deep. Single interrupted spiral ribbon with approximate 3" diameter shaft, 1-1/2" diameter welded post with 2" wide ribbons. Driven by a 10hp, 3/60/230/460 volt, 1760 rpm motor. Center bottom outlet approximately 6" diameter with manual butterfly valve. Includes top hinged cover with (2) safety grates. Mounted on a painted carbon steel frame. Serial# 4793.

Stock# 51932001

Used-Industrial Screw Conveyor, Ribbon Blender, 14.4 cuft. Stainless steel. Single Drum housing with ribbon assembly mounted on solid shaft, with double right hand outer ribbon and single left hand inner ribbon. Set Up for center discharge. T3O4LSS construction with mill finish interior and bead blast exterior. Hinged covers with single 6" diameter flanged inlet. limit switch is actuated by the covers. Center flange discharge of 6" ID with Salina Manual gate 3HP shaft mount drive with CEMA Class II reducer. Premium efficiency motor, 1750, TEFC, 3/60/230-460. 48" clearance to discharge gate.

Stock# 10715043

New- Paul O. Abbe, Model RB-15 Ribbon Blender. 15 Cubic Foot working capacity. 18 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 24.4" wide x 48.9" long x 28.8" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 7.5 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 63 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 11.8" wide x 19.7" long. Approximate 4.7" wide x 14.2" flush air operated plug valve. Discharge housing is approximate 18.5" wide x 24" long. Approximately 35.5" discharge height. Approximate weight 1,870 pounds. Approximate overall dimensions: 41.1" wide x 86.6" long x 86.6" high. Controls are available upon request.

Stock# 11585072

Used-20 Cubic Foot (approximately) T316 Stainless Steel Ribbon Blender. Double ribbon, interrupted. Ribbon 1/4' wide x 1.5". 24" wide X 6' long X 27" deep. 6" Center bottom discharge outlet. 2 Piece Hinged cover. Dual cycle motor, 15 hp 3 phase 60 cycle 230/460v, 15 hp 50 cycle 200/400v 1455 rpm.

Stock# 52159002

Used- Stainless Steel Double Spiral Ribbon Blender, Approximate 25 Cubic Foot Capacity. 1,000 Pound capacity. Approximate non-jacketed 404 (magnetic) stainless steel trough 66-1/2" long x 25--1/2" wide x 28-1/2" deep. 304 Stainless steel ribbon, driven by a 7.5hp gearhead motor. Includes lid with safety grate. 8" Diameter center bottom outlet with manual slide gate valve. Mounted on legs with casters. Previously used at food processing facility.

Stock# 51171002

Used- Gebr. Ruberg Mischtechnik KG Vertical Twin Spiral Batch Mixer, Type HM 600/656. Material of construction is 304 stainless steel (1.4301) on product contact parts. Total capacity 29.66 cubic foot (840 liter), working capacity is 21.18 cubic foot (600 liter). Inside rated for 1.5 PSI (0.1 bar). Twin shaft spiral mixing blades with a speed of 18-62 RPM by (2) drive motors. (2) Inspection doors with safety devices. Bottom product outlet. Frame mounted bottom part on 4 legs. No controls. New year 1998. CE-marked. Weight: 1.6 tonnes. Mixer (54.21") 1390 mm height, Support frame on legs 57.1" (1465 mm) height. Total height 111.34" 2855 mm. Previous used in a contract food application.

Stock# 51616001

Used-Ribbon Blender, Approximately 30 Cubic Feet Capacity, Stainless Steel. Dimple jacketed trough approximately 47" x 37" x 37". Approximate 4" diameter shaft with welded on posts and (3) welded on ribbons. Driven by 2 hp gear motor. Hinged top cover. Center bottom outlet. Mounted on (4) legs with casters. Last used on food product.

Stock# 10128063

Used- 30 Cubic Foot Total Capacity Stainless Steel Ribbon Mixer with lid missing one 23" wide section. Mixer is insulated on the long sides. Ribbon mixer inside is 30" wide x 78" log with 21" straight side. The center bottom outlet is 8" flanged. Bottom has one 1" coupling andfour tangential 2" tri-clamp nozzles. Lid has two 12" nozzles with covers. 25 hp motor and gear rducer. 230/460 vac 3 phase power required.

Stock# 10715046

New- Paul O. Abbe, Model RB-35 Ribbon Blender. 35 Cubic Foot working capacity. 39 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 33.4" wide x 59.1" long x 37.4" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 20 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 41 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 19.7" wide x 31.5" long. Approximate 4.7" wide x 14.2" flush air operated plug valve. Discharge housing is approximate 18.5" wide x 24" long. Approximately 24" discharge height. Approximate weight 2,860 pounds. Approximate overall dimensions: 52.7" wide x 107.5" long x 84.3" high. Controls are available upon request.

Stock# 50202025

Used- JH Day Stainless Steel Ribbon Blender; 35 Cubic Feet;15 HP Motor 3 Phase 208-230/460 VAC , 46 RPM; 60" x 120" x 86"; Last used for Nutritional Supplements Production

Stock# 52058002

Used- Jacketed Double Spiral Ribbon Blender / Chocolate Melter, 304 Stainless Steel. Approximate 40 Cubic Feet working capacity. Jacketed trough approximately 36" wide x 60" long x 42" deep. Jacket rated 100 psi @ 400 degrees F. 3" wide x 9/16" thick ribbons welded to approximate 3" diameter shaft. driven by a 5hp, 3/60/230/460 volt, 1750 rpm motor through reducer. 3" Tri-clamp center bottom outlet with automatic sanitary ball valve with elbow reduced to 2" dia tri-clamp. Stainless steel one piece cover with dual weighed assist arms, stainless steel safety grate. (2) 2" dia tri-clamp spray balls. (2) 8.5" stainless leg extensions. 10.5" discharge height. Mounted on stainless steel frame. Ribbon has been modified was a post style now welded to the shaft. Trough was certified by Custom mfg & polishing, national board# 143, built 2019. Serial# 53448-1.

Stock# 11252169

Used-American Food Equipment (AFECO ), Model 510, 304 Stainless Steel Dual Trough Ribbon Blender. Capacity: 90 cubic feet (50 cubic feet working). Trough dimensions: 84" long x 44" width X 38" deep, (2) sets of ribbon 22" diameter x 2-1/8" wide x 3/8" thick with safety grates, 4" diameter shaft, (2) 20" x 8" pneumatic end gate discharges with 35" ground clearance with safety grates. Powered by (2) 10 HP, 230/460 Volts, 1750 RPM , 3-phase, 60 Hz motor.

Stock# 11252167

Used-JH Day 50 Cubic Feet Double Ribbon Blender, 304 Stainless steel construction. Trough measures approx. 34" x 90" long x 40" deep with 2-Piece hinged cover and 6" diameter center bottom discharge. Includes 3" diameter shaft with double ribbon assembly. Inner ribbon dimensions: 2" wide x 1/8" thick. Outer ribbon dimensions: 1-1/4" wide x 3/8" thick. Ribbons driven by 15 HP 230/460V, 3/60Hz, 1755 RPM motor with gear reducer. Mounted on (4) legs, mild steel frame.

Stock# 10715035

New- Paul O. Abbe Model RB-65 Ribbon Blender. 65 Cubic Foot working capacity. 72 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 39.4" wide x 78.8" long x 44.1" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 25 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 36 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 4.7" wide x 14.2" flush air operated plug valve. Discharge housing is approximate 18.5" wide x 24" long. Approximately 23" discharge height. Approximate weight 5,060 pounds. Approximate overall dimensions: 60.6" wide x 131.4" long x 90.3" high. Controls are available upon request.

Stock# 52171001

Used-Ribbon Blender Approximate 65 Cubic Foot. Stainless steel construction. Unit last used for blending up to 2,800 pounds of flour-based food product. Powered by a 30 hp 3/60/230/460V motor, last ran at 208 volt. Amp rating 76/38. With New Meco shaft seals. Center bottom discharge with Roto Disk Valve. Removable stainless steel safety grates.

Stock# 11252168

Used-Stainless Steel Ribbon Mixer, approximately 80 cubic feet, trough measures 96" long X 40" wide x 44" deep, with stainless steel covers. Bottom of trough includes 7" diameter center bottom outlet, 48" off the ground. Design number 0118. Motor: 230/460 V, 60 Hz, Output RPM: 100; Ratio 17.5.101. Previously used at food processing facility.

Stock# 10715060

New- Paul O. Abbe Model RB-100 Ribbon Blender. 100 Cubic Foot working capacity. 108 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 44.9" wide x 93.8" long x 49.3" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 30 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 29 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 4.7" wide x 14.2" flush air operated plug valve. Discharge housing is approximate 18.5" wide x 24" long. Approximately 8" discharge height. Approximate weight 7,260 pounds. Approximate overall dimensions: 63.3" wide x 146.4" long x 80.8" high. Controls are available upon request.

Stock# 11252170

Used-Mixer, Double Ribbon, 100 cubic foot capacity, manufactured by GEM Equipment. Stainless steel construction. Trough measures: 84" long x 42" wide x 53" deep and ribbons measure: 2" wide x 1/2" thick. Unit has a 6" bottom discharge with a 4" side bottom pneumatic ball valve discharge. Includes (6) compartment hinged lids and a Sew-Eurodrive 1 HP, 60 Hz, 230/460V, 1751 RPM motor. Complete with start/stop controls and a gearbox. Previously used in a food operation facility. New in 1994

Stock# 61537

Used- Aaron Process Equipment Vacuum Blender/Dryer, 100 Cubic Feet. 4' Wide x 8' long x 5' deep. Dome top. Stainless steel dimple jacket rated 90 psi. 8" shaft with 1/2" x 2" inner and outer ribbon, 8" center bottom discharge. Chain drive, 20 hp 3/60/220-440/900 rpm motor thru a Foote Bros gear reducer (no tag on gearbox). Equipped with outboard bearings and packing glands.

Stock# 11059222

Used- 120 Cubic Foot S. Howes Stainless Steel Ribbon Blender. Driven by 40 hp, 208-230/460 volt motor into Gear reducer. Trough is 144" length x 48" deep x 45" wide. (2) 20 hp Bottom Side Entering Choppers/Lumpbreaker Drives with shafts and blades. 14" Center Bottom Discharge with Gemco Discharge valve with actuator. Last used in Food Plant (Bakery).

Stock# 10715039

New- Paul O. Abbe Model RB-135 Ribbon Blender. 135 Cubic Foot working capacity. 146 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 49.6" wide x 105.5" long x 53.6" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 30 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 36 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 4.7" wide x 19.7" flush air operated plug valve. Discharge housing is approximate 20.5" wide x 28.4" long. Approximately 8" discharge height. Approximate weight 7,920 pounds. Approximate overall dimensions: 64.8" wide x 158.3" long x 84.7" high. Controls are available upon request.

Stock# 10715040

New- Paul O. Abbe Model RB-165 Ribbon Blender. 165 Cubic Foot working capacity. 180 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 53.6" wide x 110.3" long x 58.3" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 40 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 36 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 4.7" wide x 19.7" flush air operated plug valve. Discharge housing is approximate 20.5" wide x 28.4" long. Approximately 4" discharge height. Approximate weight 10,164 pounds. Approximate overall dimensions: 74" wide x 167" long x 85.5" high. Controls are available upon request.

Stock# 10715045

New- Paul O. Abbe Model RB-195 Ribbon Blender. 195 Cubic Foot working capacity. 220 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 56.7" wide x 118.2" long x 62.6" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 50 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 26 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 4.7" wide x 19.7" flush air operated plug valve. Discharge housing is approximate 20.5" wide x 28.4" long. Approximately 4" discharge height. Approximate weight 11,660 pounds. Approximate overall dimensions: 76.4" wide x 183" long x 93.8" high. Controls are available upon request.

Stock# 51020001

Used- American Process Cylindrical Double Spiral Ribbon Blender, Model CRB-215, 304 Stainless Steel. Approximately 215 Cubic Foot Capacity. Non-jacket shell approximately 66" diameter x 150" straight side. Internal rated 50psi at -20 to 200 Degrees F. Double Spiral Ribbon, approximate 3" wide x 1/2" thick inner ribbon, 2" wide x 1" thick outer ribbon, welded on 7" wide posts, approximate 5" diameter shaft. Driven by a 40hp, 3/60/230/460 volt, 1775 rpm motor through reducer 89.45:1 ratio. Openings top: (2) 20" diameter manways with cover, (3) 8", 4", 2". Approximately 10" center bottom outlet with manual butterfly valve. Shell .375'' Thick, Heads .750'' Thick. Serial# 3657-B, Built 1992. National Board# 4252 certified by Lox Equipment Company.

Stock# 10211220

Used- 230 Cubic Foot American Process Stainless Steel Double Ribbon Blender. Mixing/process chamber dimensions: 62" x 120" long Drive end plate of mixer is welded, idle end is flanged and bolted Installed Meco air-purged rotary shaft seals. High polished internal surfaces with continuous double spiral ribbons. Full stainless sheet top covering with 18" x 56" ingredient (bag dump) with grating, and waterjet CIP nozzles internally installed (proximity safety switches installed on hinged panels). 10" x 6" reducer flanged, idle end product discharge with installed 6" pneumatic butterfly valve 40 hp gearmotor powered drive with chain reduction. Supply power: 230/460VAC, 60Hz, 3 ph Mild steel structural base frame.

Stock# 11059264

Used-250 CU.FT. Marion Sanitary Stainless Steel Ribbon Blender. 14,000 lb. Reliance 100 HP Motor, 1785 RPM, 460 Volts, 3 Phase. Trough Approx. 144" L x 60" W x 66" Deep. Center Bottom Discharge. Overall Dims. of Blender Approx. 186" L x 67" W x 107" H, Mounted on Stainless Legs. Last used in Sanitary Food Plant.

Stock# 10715049

New- Paul O. Abbe Model RB-265 Ribbon Blender. 265 Cubic Foot working capacity. 289 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 63" wide x 130" long x 67.8" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 60 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 26 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 4.7" wide x 27.6" flush air operated plug valve. Discharge housing is approximate 20.5" wide x 36.2" long. Approximately 4" discharge height. Approximate weight 14,960 pounds. Approximate overall dimensions: 81" wide x 206.5" long x 94.8" high.Controls are available upon request.

Stock# 49648064

Used- 304 Stainless Steel Double Spiral Ribbon Blender. Approximate 270 Cubic Foot working capacity. Non-Jacketed trough approximately 144" L x 60" W x 66" Deep. Open top, no cover. Approximate 10" diameter shaft, 1/2" thick x 3" wide outer ribbon, welded to 3-1/2" diameter posts, 7/16" thick x 3" wide inner ribbon welded to 3-1/2" diameter posts. Requires approximate 75hp motor. 20" long x 12" wide Center Bottom Discharge. Mounted on (4) stainless steel legs. 40" discharge height. Missing chain and motor.

Stock# 49648065

Used- 304 Stainless Steel Double Spiral Ribbon Blender. Approximate 270 Cubic Foot working capacity. Non-Jacketed trough approximately 144" L x 60" W x 66" Deep. Open top, no cover. Approximate 10" diameter shaft, 1/2" thick x 3" wide outer ribbon, welded to 3-1/2" diameter posts, 7/16" thick x 3" wide inner ribbon welded to 3-1/2" diameter posts. Requires approximate 75hp motor. 20" long x 12" wide Center Bottom Discharge. Mounted on (4) stainless steel legs. 40" discharge height. Missing motor.

Stock# 49648066

Used- 304 Stainless Steel Double Spiral Ribbon Blender. Approximate 270 Cubic Foot working capacity. Non-Jacketed trough approximately 144" L x 60" W x 66" Deep. Open top, no cover. Approximate 10" diameter shaft, 1/2" thick x 3" wide outer ribbon, welded to 3-1/2" diameter posts, 7/16" thick x 3" wide inner ribbon welded to 3-1/2" diameter posts. Driven by a 75hp 3/60/230/460 volt, 1770 rpm motor, through reducer. 20" long x 12" wide Center Bottom Discharge. Mounted on (4) stainless steel legs. 40" discharge height.

Stock# 49648067

Used- 304 Stainless Steel Double Spiral Ribbon Blender. Approximate 270 Cubic Foot working capacity. Non-Jacketed trough approximately 144" L x 60" W x 66" Deep. Open top, no cover. Approximate 10" diameter shaft, 1/2" thick x 3" wide outer ribbon, welded to 3-1/2" diameter posts, 7/16" thick x 3" wide inner ribbon welded to 3-1/2" diameter posts. Driven by a 75hp 3/60/230/460 volt, 1770rpm motor, through reducer. 20" long x 12" wide Center Bottom Discharge. Mounted on (4) stainless steel legs. 40" discharge height.

Stock# 49648071

Used- 316 Stainless Steel Double Spiral Ribbon Blender. Approximate 270 Cubic Foot working capacity. Non-Jacketed trough approximately 144" L x 60" W x 66" Deep. Open top, no cover. Approximate 10" diameter shaft, 1/2" thick x 3" wide outer ribbon, welded to 3-1/2" diameter posts, 7/16" thick x 3" wide inner ribbon welded to 3-1/2" diameter posts. Driven by a 75hp 3/60/230/460 volt, 1770rpm motor. Approximate 20" long x 12" wide center bottom discharge. Mounted on (4) stainless steel legs. 40" discharge height. Missing chain, gearbox, guarding.

Stock# 49648072

Used- 316 Stainless Steel Double Spiral Ribbon Blender. Approximate 270 Cubic Foot working capacity. Non-Jacketed trough approximately 144" L x 60" W x 66" Deep. Open top, no cover. Approximate 10" diameter shaft, 1/2" thick x 3" wide outer ribbon, welded to 3-1/2" diameter posts, 7/16" thick x 3" wide inner ribbon welded to 3-1/2" diameter posts. Driven by a 75hp, 3/60/230/460 volt, 1770rpm motor, through reducer. 20" long x 12" wide Center Bottom Discharge. Mounted on (4) stainless steel legs. 40" discharge height. MISSING CHAIN, GUARDING.

Stock# 10715051

New- Paul O. Abbe, Model RB-315 Ribbon Blender. 315 Cubic Foot working capacity. 356 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 65.4" wide x 141.8" long x 73.3" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 75 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 19 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 5.5" wide x 27.6" flush air operated plug valve. Discharge housing is approximate 20.5" wide x 36.2" long. Approximately 4" discharge height. Approximate weight 19,580 pounds. Approximate overall dimensions: 87.8" wide x 218.4" long x 100.4" high.Controls are available upon request.

Stock# 10715053

New- Paul O. Abbe, Model RB-375 Ribbon Blender. 375 Cubic Foot working capacity. 441 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 67.7" wide x 157.5" long x 78.8" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 75 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 19 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 5.5" wide x 27.6" flush air operated plug valve. Discharge housing is approximate 20.5" wide x 36.2" long. Approximately 4" discharge height. Approximate weight 20,944 pounds. Approximate overall dimensions: 91.9" wide x 237.1" long x 104.7" high. Controls are available upon request.

Stock# 11059262

Used- Hayes and Stolz 700 Cu.Ft. Stainless Steel Ribbon Blender, Model 90x180. Trough is 90" wide x 180" Length x 108" Deep. Driven by 40 HP, motor into gear reducer. Approx. 10'6" OAH x 21' OAL. Last used as Polytetrafluoroethylene (PTFE) Pellet Blender. Rated 700 Cu.Ft. with materiel 15-30 LBS/Cu.FT.

Stock# 11059263

Used- Hayes and Stolz 700 Cu.Ft. Stainless Steel Ribbon Blender. Model 90x180. Trough is 90" wide x 180" Length x 108" Deep. Driven by 40 HP, motor into gear reducer. Approx. 10'6" OAH x 21' OAL. Last used as Polytetrafluoroethylene (PTFE) Pellet Blender. Rated 700 Cu.Ft. with materiel 15-30 LBS/Cu.FT.