Used Screw Dewatering Presses

Stock# 53279008

Used-EnoRossi IdroPress Bladder Press, Approximately 28" diameter x 33" high. More photos upon request.

Stock# 53018001

Used- Brown International Lab Juice Finisher, Model 3600. Stainless Steel, Approximate 2 to 10 gallons per minute (120 to 600 gph), Up to 40 psi extraction pressure. 12" x 12" Infeed Hopper, Approximate 5" diameter x 16" long screw, driven by approximate 2hp 3/60/230/460v Motor, Mounted on (4) carbon steel legs.

Stock# 52741001

Unused- Vincent Screw Press, Model CP-4. Includes: Main Drive: 1.5 HP Leeson Motor; Nord Gearbox 89:1; Genesis VFD 1.5 HP; J/M Shaft Seal; Bronze Discharge End Bushings; 4 Bar Mechanism with UHMW Donut; Screw 4" Feed Pitch Zone; .109 WW Screen; Resistor Bar Assembly; Bimba Air Cylinder 3" Bore, 4" Stroke; Parker Air Filter, Regulator with gauge. Single Phase, 60 Hertz, 110 Volt. Mfg. 2019

Stock# 53479001

Used-Vincent Screw Press, Model CP-4-VT, Stainless steel. Vapor Tight. Capable of 110 lbs per hour. -98% oleoresin recovery and 75-80% ethanol recovery. -4" diameter screw with four stages of compression features interrupted, reducing pitch flights. This design allows the press to accept variations in input volume and consistency without adjustment, --Powered by Lesson 1.5 HP Motor. Model # 145T17XK6A with Nord Drive Systems Gear Box. Ratio 88.74 to 1. Model # 3282AFBVLN140TC. -KC Genesis AC Motor Speed Control. Model # KBAC-27D (3G) (GRY) (9520T). -Food grade ready on all contact components Explosion proof motor -Mounted on stand with (4) casters.

Stock# 52411001

Used- Jiangsu Kuwai Rough Crushing Juice Machine, Model PS-LZ-1.5. Stainless steel construction. Approximate 0.3 - 1.5 tons per hour production capacity. Consisting of Kuwai top mounted crusher, driven by a 2.2kW, 3/60/480 volt, 1740 rpm motor. Kuwai juicer driven by a 4kW, 3/60/480 volt, 1740 rpm motor. Mounted on stainless steel frame with casters.

Stock# 46971068

Used- FKC Screw Press, Model SHX-600X3500L, 304 Stainless Steel. Approximate capacity 35-90 kg/hour, depending on product. Maximum pressure 0.7 MPa. Approximate 600mm diameter x 3500mm long screw. Top end feed, bottom end discharge, bottom drip pan. Requires drive and reducer. Mounted on an I-beam carbon steel frame. Serial # M-2430.

Stock# 46971033

Used- FKC Screw Press, Model SHX-800X6000L, 316L Stainless Steel. Maximum pressure 0.7 MPa. Approximate 800mm diameter x 6000mm long screw. Top end feed, bottom end discharge. (4) external screen assembly spray bars, bottom drip pan. Driven by a 30hp, 3/60/460 volt, 1175 rpm motor thru a reducer, ratio 319 to 1. Mounted on an I-beam carbon steel frame. Serial# M-2448,

Stock# 46971034

Used- FKC Screw Press, Model SHX-800X6000L, 316L Stainless Steel. maximum pressure 0.7 MPa. Approximate 800mm diameter x 6000mm long screw. Top end feed, bottom end discharge. (4) external screen assembly spray bars, bottom drip pan. Driven by a 30 hp, 3/60/460 volt, 1175 rpm motor thru a reducer, ratio 319 to 1. Mounted on an I-beam carbon steel frame. Serial # M-2428.

Stock# 53534001

Used- Goodnature Juice and Cider Press, Model SX280. Rated for output of up to 450 gallons/hour (1700 liters/hour), 2-3 tons/hour; Press features "squeezebox" design plates constructed of stainless steel; On/Off and Forward/Reverse Controls; 1/50/380VAC. Includes: Stainless steel Fitzmill type mill; Auger pump and pomace pump; Custom built pasteurisation bath, fully insulated and 100% food grade stainless steel. This model is designed for running hard vegetables, leafy greens, most fruits and nuts for plant based milks (i.e. apple, kale, pineapple, spinach, almonds and other nuts, beets, celery, carrot, herbs, lemons and much more).

Stock# 52848002

Used- JBT Foodtech Finisher, Model UPF200. Paddle type finisher. Primary juice flow 50 - 150 gpm. Pulpwash flow 25 - 95 gpm. Oil recovery flow 48 - 120 gpm. d-Limonene recovery flow 33 - 100 gpm. Screw infeed. Approximate 30-1/2" wide x 36" long x 26" deep chamber. Approximate 2-1/2" diameter shaft with 2-1/2" to 1-1/8" wide x 1/2" thick spiral blade. Driven by a 25hp, 3/60/230/460 volt, 1770rpm motor. 34" long x 15" diameter screen, approximate 1/8" diameter holes. Mounted on frame. Incomplete CIP system. Serial# 13-29.

Stock# 52848014

Used- JBT Foodtech Finisher, Model UPF200. Paddle type finisher. Primary juice flow 50 - 150 gpm. Pulpwash flow 25 - 95 gpm. Oil recovery flow 48 - 120 gpm. d-Limonene recovery flow 33 - 100 gpm. Screw infeed. Approximate 30-1/2" wide x 36" long x 26" deep chamber. Approximate 2-1/2" diameter shaft with 2-1/2" to 1-1/8" wide x 1/2" thick spiral blade. Driven by a 25hp, 3/60/230/460 volt, 1770rpm motor. 34" long x 15" diameter screen, approximate 1/8" diameter holes. Mounted on frame. Incomplete CIP system. Serial# 13-30.