Food and Beverage Equipment

Used ICMA San Giorgio 140mm Twin Screw Extruder | 36:1 L/D | Co-Rotating | Segmented Screws | Screen Changer & Pelletizer

Used ICMA San Giorgio 140mm Twin Screw Extruder | 36:1 L/D | Co-Rotating | Segmented Screws | Screen Changer & Pelletizer. Segmented screws. Reinforced gearbox & motor. Electric panel overhauled in 2015, touch control added. Incl. Screen changer and Dry pelletizing unit. Previously used on elastomers TPE, TPU, SBS. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.

Used 140 Cu Ft Dual Shaft Ribbon Blender – Stainless Steel Industrial Mixer

Used Dual Shaft Ribbon Blender, Approximately 140 cuft / 1100 Gallon capacity. Stainless steel. Dimple Jacket. Bottom Discharge: (2) 10" ports, one for each screw, Trough dimensions: Length: 119 inches Height: 46 inches Width: 47 inches. Height off ground: 12 inches Bottom discharge. (2) 575 Volt, 15 HP motors. (Motors will be switched out to (2) Used US voltage Motors;

Installed but Unused- Southern Heat Exchanger Shell & Tube Heat Exchanger, 140.

Unused, Installed and removed. Southern Heat Exchanger Shell & Tube Heat Exchanger, 140.4 Square Foot, Carbon Steel, Horizontal. Carbon steel shell rated 700 psi/ full vacuum at -20 to 300 degrees F. (61) Carbon steel 3/4" diameter x 12' long x 12 gauge straight tubes rated 198 psi / full vacuum at -20 to 400 degrees F. Openings: shell side (4) 2", tube side (2) 2". Saddle mounted. Serial# 01-041, National Board# 10959, Built 2001. Wt. 2,100#.

MFR: Southern Heat Exchanger

Used 14,000 Gallon 316L Stainless Steel Vertical Tank – Erected Steel Products, API-650, Side Agitator

Used- Erected Steel Products 316L Stainless Steel Vertical Tank, 14,000 gallons. 13' diameter X 15' high straight side. Rated ATMOS @ 20 to 160 F. S/N 1172. API-650 standard. Slight cone top, flat bottom with ramped side. Top fittings: 20" manway, (1) 6" vent, (1) 2", and (1) 16" X 16" feed inlet. 24" side bottom manway, (1) 2.5", (2) 10", (1) 3", and (1) 6" side inlet and outlets. (2) 8" side bottom outlets. Built 2012. Agitator in hot;s not included.

Used 14,000 Gallon 316L Stainless Steel Vertical Tank – Erected Steel Products, API-650, Built 2012

Used-14,000 gallon Erected Steel Products 316L Stainless Steel Vertical Tank. 13' diameter X 15' high straight side. Rated ATMOS @ 20 to 160 F. S/N 1168. API-650 standard. Slight cone top, flat bottom with ramped side opposite where agitator was mounted (agitator no longer available). Top fittings: 20" manway, (1) 6" vent, and (1) 12". 24" side bottom manway, (1) 2" (1) 3", (1) 6", (3) 8", (3) 10" and (1) 12" side top inlets (2) 8" side bottom outlets. Built 2012.

Used 14,000 Gallon 316L Stainless Steel Vertical Tank – Erected Steel Products, API-650, Agitated, Built 2012

Used-14,000 gallon Erected Steel Products 316L Stainless Steel Vertical Tank. 13' diameter X 15' high straight side. Rated ATMOS @ 20 to 160 F. S/N 1169. API-650 standard. Slight cone top, flat bottom with ramped side opposite where the agitator was mounted (agitator no longer available). Top fittings: 20" manway, and (1) 6" vent. 24" side bottom manway. (1) 12" and (1) 24" side top inlets. (1) 6" , (1) 8", and (1) 10" side inlets. (1) 2.5", (2) 8", (1) 3", and (1)4" side bottom outlets. Built 2012.

Used Littleford Model FKM-4000-D Stainless Steel Jacketed Plough Mixer – 4000L Capacity

Used- Littleford Model FKM-4000-D Stainless Steel Jacketed Plough / Plow Mixer. 4000 Liter Capacity. Jacket rated 75 PSI at 320 Degrees F. National Board# 1272. Driven by 125 HP, 460 volt motor into gear reducer. Serial # 40671-3267. All product surfaces 316 Stainless Steel, polished to 120 Grit. OAD: Approx. 16' L x 6' W x 8' h. RECONDITIONED AND NOT USED SINCE.

MFR: Littleford

Used Littleford Vacuum Plow Mixer/Dryer – Model VT-4000 (4000L Capacity)

Used Littleford Vacuum Plow Mixer/Dryer Model VT-4000 (4000L Capacity), 304 Stainless Steel. Approximately 54" diameter x 121" straight side with dished ends. Internal rated 15 PSI/VACUUM @ 250 degrees f., Stainless steel jacket rated for 75 psi at 250 deg.f. 6" diameter shaft, 8 bolt-on plow blades, 2 end scrapers, provision for 4 choppers, air purged main seals. Driven by a 50hp motor through gearbox. Various top openings. 6" diameter off-center bottom outlet. Unit mounted on carbon steel frame. Included VFD Control Panel. National Board# 1260. Serial# 11363.

MFR: Littleford

Used – Aurora Industrial Machining Horizontal Shell & Tube Heat Exchanger – 150 PSI, Carbon Steel

Used Aurora Industrial Machining Horizontal Shell & Tube Heat Exchanger, Approximately 142 square feet. Carbon Steel shell rated 150psi at -20 to 350 Degrees F. (109) 304 stainless steel straight tubes, 0.625" diameter, rated 150psi at -20 to 350 Degrees F. Openings shell: 2" (inlet), 2" (outlet), 2" (relief), tubes: 8" (inlet), (4) 3/4" (vent/drain). National Board# 3012, Serial# 4095, built 1996.

MFR: Aurora

Industrial Unused Southern Heat Exchanger Shell & Tube Heat Exchanger – 1459 Sq Ft, 304L Stainless Steel

Unused- Southern Heat Exchanger Shell & Tube Heat Exchanger, Approximately 1459 Square Feet, 304L Stainless Steel, Horizontal. 304L Stainless steel shell rated 103 psi at -20 to 250 degrees F. (186) 304L Stainless steel 1-1/2" diameter x 19 11-3/4" long, rated 127 psi at -20 to 250 degrees F. 304L Stainless heads and tubesheet. Openings: (4) .75", (1) 1-1/2", (2) 8", (2) 12". Saddle mounted. National Board# 15648, Serial# 20-0055, Built 2020.

MFR: Southern Heat Exchanger

Used Cumberland FX1018 Granulation System with Airveyor, Cyclone & Blower – 15 HP Industrial Plastic Granulator (2022)

Used- Cumberland Granulation System, Model FX1018. Serial# FX1018-22012. 10" x 18" feed throat. 3 knife open rotor with two bed knives. Offset cutting chamber. 15 HP 230/460-volt motor. Granulator & blower are setup for 230-volt operation. Insulated flex feed in-feed hopper and body panels. 4" OD airveyor discharge. Mounted on casters. System includes Sterling 4002FD blower, size 6 cyclone, stand, filter head with bags. and lot of connecting pipe. 3/16" holes screen is installed. Built 2022.

MFR: Cumberland

Used Irwin Chesaw Granulator – Model CH-LH 28.7-04, 15 HP with Auger Discharge

Used- Irwin Chesaw Granulator; Model CH-LH 28.7-04. 5" x 33" Rotor Cutter, 15 hp, 208-230/460 volt, 1760 rpm, Fan Cooled 10:1 gearbox. Lincoln Auto-Lube System. Evacuated by a 4" Auger Discharge System. Approximate 3/8" Holes Screen. Mounted on Casters. Starter and Controls for Blower, Auger System and Siemens Micromaster 440 Variable Speed Drive Unit for Granulator Rotor Speed. Also Includes 5 hp; 208-230/460 volt 3460 rpm Blower with Steel Impeller, OK100 (4") Outlet, Lab Test Machine.

MFR: Irwin-Chesaw