Cosmetics Equipment
Stock No.:
54520003Used 5,600 Gallon Pinnacle Manufacturing Horizontal Carbon Steel Mix Tank with Dual Agitators – Built 2023
Used 5,600 Gallon Pinnacle Manufacturing Horizontal Carbon Steel Mix Tank with Dual Agitators Built 2023. Approximate interior dimensions: 86'' wide x 236'' long x 66'' tall. 36'' roof manway, 22'' front manway. (2) Top entering agitators, with 8 blades each. (1) 4'' drain valve at front and back. Front sight glass. Serial # AL8400, built 2023.
MFR: Pinnacle Stainless
Stock No.:
54520004Pinnacle Manufacturing 5,600 Gallon Horizontal Mixing Tank with Dual Agitation System and Carbon Steel Construction
Pinnacle Manufacturing 5,600 Gallon Horizontal Mixing Tank with Dual Agitation System and Carbon Steel Construction. Carbon steel construction. Approximate interior dimensions: 86'' wide x 236'' long x 66'' tall. 36'' roof manway, 22'' front manway. (2) Top entering agitators, with 8 blades each. (1) 4'' drain valve at front and back. Front sight glass. Serial # AL8401, built 2023.
MFR: Pinnacle Stainless
Stock No.:
52283022Used Farr Tenkay Model 2C Cartridge Type Dust Collector – 800 CFM, 1.5 HP Blower
Used- Farr Tenkay Model 2C Cartridge Type Dust Collector. 800 CFM. Rated for 564 square feet filtering area with (2) cartridges measuring 12.75" diameter x 26" long. Includes 6" air inlet, 6" outlet, hinged door, 15" diameter cone bottom discharge. Offered with Cincinnati Fan Model FB/12A Blower, driven by 1.5 HP, 3-phase, 60 Hz, 208-230/460 Volt, 3450 RPM motor. Serial# 9210.
MFR: Farr Co
Stock No.:
10151633Used Mueller 5,700 Gallon Jacketed Pressure Tank | 21,000 Liter Stainless Steel Fermentation Vessel
Used Mueller 5,700 Gallon Jacketed Pressure Tank | 21,000 Liter Stainless Steel Fermentation Vessel, Model F.95" ID x 155" T/T. 268" OAH.Internal 25 psi at 100 degrees F, Jacket rated 100 psi at 100 degrees F.304 stainless steel, vertical, dish top and cone bottom, 16" bottom manway with 3" CBO.Serial # 384634-4, Built 2008.Previous use was brewing beer.
MFR: Mueller Corp
Stock No.:
41174072Used Escher Wyss ZW 2350 Double Drum Dryer | 1,000 kg/hr | Industrial Drum Drying System
Used Escher Wyss ZW 2350 Double Drum Dryer | 1,000 kg/hr | Industrial Drum Drying System. Capacity 1000 Kgs/Hr (2200 Lbs/Hr) 1500 mm (58.5") dia x 2500 mm (97.5") st. side drums. 26 RPM drum speed. Heating pressure 8 bar (120 PSI), Heating steam pressure 4 bar (60 PSI). Complete with (1) Blower, (1) Dust collector, Sifter/5 Station sack filling unit and additional infrastructure. Previously skimmed milk concentrated with 45% dry matter content. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.
MFR: Escher Wyss
Stock No.:
409352Pre-Owned Vulcan K6ETT Electric Counter Kettle | 6 Gal | 50 PSI
Used Vulcan-Hart Model K6ETT Electric Counter Tilting Kettle, 6 Gallon Capacity. Approximately 11.8" Diameter x 14-1/2" deep. Ellipsoidal bottom. 2/3 Jacketed rated 50psi at -20 to 300 degrees F. Frame mounted. National board# 21596, Serial# 46-3002235, Built 2011. 3/1PH 50/60HZ 8/10KW 208/240V requirements.
MFR: Vulcan
Stock No.:
47890001Lodige FKM600D Plow Mixer
Used- Lodige Model FKM600D batch-type plow mixer with 6 cubic feet working capacity and 10 cubic feet total capacity. 304 stainless steel, non-jacketed mixing chamber approximately 32" diameter x 50" long with 4" diameter shaft, (3) bolt-on plows, (2) bolt-on end scrapers, (2) 18" x 15-1/2" side access doors, and (2) 12" top openings. 9" x 7" bottom outlet with manually operated door and air-purge seals. Serial # 9046. Driven by an approximately 10 hp motor through Falk reducer. Includes control panel with Allen-Bradley PanelView 600 and SLC 5/04 CPU. Mounted on carbon steel stand. Suitable for dry powders, premixes, granular ingredients, spices, nutraceuticals, feed additives, chemical blends, and similar products.
MFR: Lodige
Stock No.:
50556009Used - Paint Media Mill, 8" x 30" Milling Chamber, 6 Gallon, 10 HP Motor
Used- Paint Media Mill. includes 8" diameter X 30" high milling chamber, approximate 6 gallon. Stainless Steel screening section, jacketed chamber. Driven by 10 HP, 220/440 V, 1740 RPM, 3-phase, 60 cycle motor. Previously used at paint processing facility and in working condition when removed from service. No Manufacturers Tag.
MFR: Unknown
Stock No.:
51065016Used Stewart Bolling 6" x 12" Two Roll Mill – Industrial Rubber & Plastics Processing
Used- Stewart Bolling 6" x 12" Pilot Two Roll Mill. Approximate 6" diameter x 12" long chrome cored rolls. Driven by 5 hp, 3/60/220/440 volt gear motor, single speed, fixed gear ratio. Unit has front and back knee safeties, and over the roll safety cage. Two point manual adjustment, split end guides. Serial# 2560.
MFR: Stewart Bolling
Stock No.:
54180001Farrel Rubber/Plastic Laboratory Calender Mill – Inverted "L" 4-Roll, Adjustable Knives
Used- Farrel 4-Roll Inverted "L" Rubber/Plastic Laboratory Calendar Mill. 6" D x 13" L rolls. 500 degrees F max. roll temp. Up to 35 RPM. Fixed center roll w/ adjustable bottom, top, and offset. Full herringbone even speed gears on one side, Full herringbone friction gears on the other side. Nylon adjustable infeed guides. (2) adjustable twin knives on bottom roll. Cable safeties on both sides of frames. SCR drive w/ dynamic braking; Operators control station with variable speeds. Variable speed 7.5 HP motor. 3/460V. Serial# 73A1499.
MFR: Farrell
Stock No.:
54280001Used Buflovak Atmospheric Double Drum Dryer | Model 6" x 8" ADDD | Pilot & R&D D
Used Buflovak Atmospheric Double Drum Dryer, Model 6" x 8" ADDD. 2 sq/ft Total drying surface area. Approximate 6" diameter x 8" face cored drum, rated 140-160 psig. Driven by a 1/2hp, 3/60/208-230/460 volt, 1725rpm motor through reducer 41.58:1 ratio. Blador VS drive. The dryer features twin chrome-plated drying drums with independent drum gap adjustment, stainless steel frame and safety guards, product feed trough with feed manifold, and doctor blade assembly. Compact unit is designed for drying slurries, purees, pastes, and other pumpable materials into flakes or powders and is well suited for R&D, product development, and small-scale production. Mounted on stainless steel frame. Job No. P1-00972, Serial# 2013-04, built 2013.
MFR: Buflovak
