Price Recently Reduced Process & Packaging Equipment Inventory

Stock# 40958019

Unused- 2023 Cummins C50D6C Generator 50kW. Open skid 120/208 volt 3 phase 60 hz Diesel generator 50 Gallon Pryco Day Tank Generator breaker 70amp / 125amp / 175 amp 2 / ATS 125 AMP and 70 AMP Split loads Exhaust System with Particulate filter. 3

Stock# 42505001

Used Rotary Blancher, 304 Stainless Steel. Perforated drum approximately 40" diameter x 98" long, driven by a 2 hp, 3/60/208-230/460 volt, 1755 rpm Reeves variable speed motor, ratio 70.6 to 1, minimum / maximum rpm 6.6/60. 3/16" Diameter screen holes, side access doors. End feed and discharge. Mounted on a stainless steel frame.

Stock# 42818001

Used Draisewerke Perl Mill, Stainless Steel. Grinding vessel volume net- 62 Liters. Model DCP-MEGAFLOW ACS-800/PUC. Vessel rated 3 Bar (45 PSI) at 70 Degrees C. (158 Degrees F), jacket rated 3 Bar (45 PSI) at 40 Degrees C. (104 Degrees F). Hydraulic chamber raise, and lower with power pack. Double acting mechanical seal. Rotor and bowl are coated. Driven by a 300 HP, 3/60/460 Volt, 1190 RPM motor. Includes a control panel with an ABB drive. Built 2005.

Stock# 45003001

Used Alfa Laval / Sharples PM-3600 Super-D-Canter Centrifuge. 316 Stainless Steel construction (product contact areas), maximum bowl speed 3500 rpm, 4-1/2" single lead conveyor, liquid plate dams, gearbox 125:1 ratio, base, casing, approximate 37kw (49.6hp) main drive motor (380/50/3), back drive moto. Mounted on a carbon steel sub-frame with vibration isolators, safety guards.

Stock# 45648001

Used Alfa Laval / Sharples PM-40000 (Same as a P-4600) Super-D-Canter Centrifuge. 316 Stainless steel construction (product contact areas), maximum bowl speed 3350 rpm. 5.5" single lead conveyor with sintered tungsten carbide wear protection tiles, hogged-out cake discharge ports with replaceable wear liners, base, casing, feed pipe, P90 gearbox 98:1 ratio, main drive sub-base, 60 hp drive motor, 575/3/60, Eddy current backdrive, lube system, vibration isolators, safety guards, includes control panel with Danfoos electronic drive.

Stock# 45648002

Used Alfa Laval / Sharples Model PM-40000 (Same as a P-4600) Super-D-Canter Stainless Steel Centrifuge. 316 Stainless steel construction (product contact areas), maximum bowl speed 3350 rpm. 5.5" single lead conveyor with sintered tungsten carbide wear protection tiles, hogged-out cake discharge ports with replaceable wear liners, base, casing, feed pipe, P90 gearbox 98:1 ratio, main drive sub-base, 60hp drive motor, 575/3/60, Eddy current back drive, lube system, vibration isolators, safety guards, includes control panel with Danfoos electronic drive.

Stock# 46041002

Used Flottweg Z4D/4-454 Solid Bowl Decanter Centrifuge. 316 Stainless Steel construction (product contact areas), maximum bowl speed 3500 rpm, approximate 5" single lead conveyor with welded hardfacing. Rotodiff backdrive with powerpack, feed pipe, lubrication system, adjustable liquid plate dams, 30 KW (40.2hp) ABB main drive motor with fluid coupling, frame/casing, vibration isolators, safety guards. Last used for wastewater treatment.

Stock# 46431001

Used Alfa Laval Aldec-404 Solid Bowl Decanter Centrifuge. 316 Stainless Steel construction (product contact areas). Maximum bowl speed 4000 rpm, single row of lined cake discharge ports, 110mm single lead conveyor with welded hardfacing, moon liquid plate dams, base, casing, 2.5 KNM gearbox with 159:1 ratio, feed pipe, 22 kw 380/3/50 drive motor, DC backdrive motor.

Stock# 46573001

Used Alfa Laval AVNX-426B-31G (same as a PM-36000) Solid Bowl Decanter Centrifuge, 316 Stainless steel construction (product contact areas). 5.5" single lead conveyor with sintered tungsten carbide wear inserts, maximum bowl speed 3250 rpm, 360 degree solids discharge ports, moon liquid plate dams, bowl, P125 gearbox (125:1 ratio), base, casing, lubrication system, 37 kw,(49.6hp) 690/3/50 main drive, back drive, feed pipe with poly addition port, vibration isolators, vibration switch, safety guards, control panel.

Stock# 46665001

Used Alfa Laval WSPX-307-71G Desludger Disc Centrifuge. 316 Stainless steel (bowl assembly with aluminum bowl covers). Maximum bowl speed 8375 rpm, concentrator design (liquid/liquid/solids separation), light phase centripetal pump liquid discharge, belt drive configuration, 7.5kw drive motor 380/3/50. Mounted on frame. Rated approximate 22 GPM, sludge space 0.87 gallons.

Stock# 47049001

Used Alfa Laval / Sharples P-3000 Super-D-Canter Centrifuge. 316 Stainless Steel construction (product contact areas), maximum bowl speed 4000 rpm, 4" double lead conveyor with welded hardfacing, hogged-out cake discharge ports with cake flingers, liquid plate dams, base, casing, gearbox with torque arm assembly, feed pipe, vibration isolators. Bowl driven by 28.5hp (21.3 kW), 460/3/60 main drive motor.

Stock# 47049003

Used Alfa Laval / Sharples Model P-3000 Super-D-Canter Centrifuge. 316 Stainless Steel construction (product contact areas), maximum bowl speed 4000 rpm, 4" single lead conveyor with welded hardfacing, single row lined cake discharge with cake flingers, liquid plate dams, base, casing, gearbox with torque arm assembly, feed pipe, vibration isolators. Bowl driven by a 28.5hp (21.3kW), 3/60/460 volt, 1765 rpm main drive motor.

Stock# 47083001

Used Flottweg Z5L Solid Bowl Horizontal Decanter Centrifuge. 316/329 Stainless steel construction (product contact areas), maximum bowl speed 2650 rpm, single lead conveyor with welded hardfacing, cyclo gearbox, stainless steel discharge chutes, standard feed pipe, grease lubrication system, adjustable liquid plate dams, fiberglass bowl cover, base, 55 kw, 380/3/50 main drive.

Stock# 47200002

Used Alfa Laval Solid Bowl Decanter Centrifuge, Model AVNX-616B-31G, 316 stainless steel (product contact areas). Maximum bowl speed 3250 rpm, single lead conveyor with welded hardfacing, moon liquid plate dams, base, casing with cake vibrator, feed pipe, 2.5 Knm gearbox, 11Kw 380/3/50 main motor.

Stock# 47768002

Used Tranter Superchanger Approximate 878.8 Square Feet Surface Area Plate Heat Exchanger, Model 06-T16-UP-146. Approximate (146) 29" wide x 68" tall 316 stainless steel plates rated 150 psi at 20 to 200 degrees F. (2) 6" Diameter, (2) 8" diameter inlet & outlets. Mounted on an expandable carbon steel frame. Serial #SC-22880. Shop order # 83735. Built 1999. No National Board #. Unit is U stamped.

Stock# 48445002

Used Alfa Laval Plate Type Heat Exchanger, Model MX25-BFG. 2906 Square Feet, Vertical. (182) Approximate 24" wide x 85" tall x 0.40mm 304 stainless steel plates rated 150 psi at -20 to 150 degrees F. (2) 8" Inlets, (2) 8" outlets. Mounted on expandable frame with carbon steel end plates. Serial # 30110-65664. National Board # 24801. Built 2006.

Stock# 48575002

Used Alfa Laval DS-401 Solid Bowl Decanter Centrifuge. Stainless steel construction (Product contact areas), maximum bowl speed 3200 rpm, base, casing, Includes (2) Seepex pumps, feed pump, centrate water pump, built in muffin. Monster on the feed line, dam plates, programming software. Mounted in 28' box truck. Reported to be reconditioned.

Stock# 48918013

Used 34,600 Gallon Tank, 316 Stainless Steel from top to sidewall. Ladder, platform and safety railing. Dimensions: 30' Tall x 14' Diameter

Stock# 48996002

Unused- Alfa Laval Fermenter / Reactor, Approximate 40 Liter (10.5 Gallon), 316L Stainless Steel, Vertical. Approximate 12" diameter x 22" straight side, bolt-on flat top, dished bottom. Internal rated 45 PSI/FV at -20 to 400 degree F. 316L Stainless steel Jacket rated 150 psi/FV at -20 to 400 degree F. Bottom entering agitation 1/2hp drive, missing agitator. (1) Spray ball. Side lug mounted with load cells. National Board #264. Serial #786-100/17. Built 2004. Includes control panel with Wedgewood technology model 653 absorbance monitor, Mettler toledo Jag xtreme digital read out, (4) metering valves. All mounted on stainless steel frame.

Stock# 49825001

Used Benier Baguette and Roll Line with VMI Verymixer. The line can make long pieces of bread much like a baguette. Rated at 600 grams per piece, it can do about 3,000 pieces per hour. At 350 grams it is rated for approximately 3,200 pieces per hour. Bread line mixer has an output of 1,800 kg per hour. The Benier moulder output varies greatly depending on the size of each piece. Capacity: 3,000 Dough Pieces Per Hour. Dough Weight: 250 - 465 Grams (8.81 oz - 16.40 oz). Cutting Pattern: 1, 2, 3, 4, 5. And 6 Parts Pan Dimensions: 800mm x 600mm x 40mm (31.49" x 23.62" x 1.57"). The entire line is manufactured by Benier in 2002, with the exception of the mixer being a VMI mixer. Year 2002.

Stock# 50028005

Unused- JBT Foodtech FORMCOOK Progrill Contact Cooker. Model PB-1542 Electric ProBake. With 10 Degree Incline and Top Belt. Overall Belt Width 60". Usable Belt Width 59", Cooking Length 13.78'. Seven Lower Electric Platens, Upper and Lower Teflon Style Belting. Electrical Specifications 460/3/60 (110/1/60), Electric Drive, Basic Belt Cleaning System, Digital Read-out System, 12" Out-feed Conveyor, Standard Exhaust Fan. Controllogix Processor disconnects on all motors. HMI Screen A. Platens 3/60/460 / 1/60/110 Electric Drive.

Stock# 50388017

Used A&B Process Systems Reactor. Approximate 400 Gallon, 304L Stainless Steel, Vertical. 54" Diameter x 24" straight side, Dished top, jacketed hemispherical bottom. Internal rated 150 psi at -20 to 425 degrees F. 304L stainless steel jacket rated 150 psi at -20 to 425 degrees F. Off center top entering angled anchor agitator with scrapers, driven by a 10 hp, 3/60/230/460 volt, 1770 rpm gear motor, ratio 40.80 to 1. Openings top: 18" man way with davit arm cover. 4" Center bottom outlet. Mounted on (3) side lugs. Serial # 1118160301B. National Board #1606. Built 2012.

Stock# 50388105

Used IKA Works Inline Dispax Reactor. Mixing/Homogenizing/Dispersing, Model MHD/DR-PB 20. Nominal flow rate 30 gallons per minute, solids capacity 6200 pounds an hour. Driven by a 50 hp, 3/60/460 volt, 3535 rpm motor. 4" Solid inlet, 3" liquid inlet, 2" outlet. Unit mounted on a base Part # P015897. Serial # 2603-12.

Stock# 50388107

Used IKA Works Dispax Reactor High Shear Inline Disperser, Model DR 2000/10, Stainless Steel. Nominal flow rate 35 gallons per minute (8,000 l/h), nominal tip speed 4500 feet per minute. Driven by a 30hp, 3/60/230/460 volt, 3525 rpm motor. 2" Inlet & outlet. Unit mounted on a base. Part# P015742. Serial # 2599-12.

Stock# 50388113

Unused- IKA Colloid Mill, Model MK 2000/50. Nominal flow rate 350 gallons per minute, maximum flow rate 60,000 l/h, nominal tip speed 23 meters per second. Driven by a Siemens 150hp Motor. 480 Volt, 1785 rpm. Serial# 2758-16

Stock# 50388115

Unused- IKA Works Inline Colloid Mill, Model MK 2000/50. Nominal flow rate 350 gallons per minute, maximum flow rate 60,000 l/h, nominal tip speed 23 meters per second. Driven by a 150hp, 3/60/460 volt, 1785 rpm motor. 8" Inlet, 6" outlet. Unit mounted on a base. Part# P016866, serial# 2756-16.

Stock# 50388116

Unused- IKA Works Model MK 2000/50 Inline Colloid Mill. Nominal flow rate 350 gallons per minute, maximum flow rate 60,000 l/h, nominal tip speed 23 meters per second. Driven by a 150hp, 3/60/460 volt, 1785 rpm motor. 8" Inlet, 6" outlet. Unit mounted on a base. Part# P016866, serial# 2757-16.

Stock# 51094121

Used Westfalia OTA30-00-066 Solid Bowl Disc Centrifuge. Bowl speed 6590 rpm. Driven by a 10hp, 3/60/208-230/460 volt, 1760 rpm XP motor. Aluminum case with cover, Nickel bowl. Serial # 1676985.

Stock# 51188001

Used GEA Niro Spray Dryer Atomizer, Stainless steel. Overall size is 1.2 meter x 1.2 meter x approximately 2 meter high. Does not include the spray nozzle.

Stock# 51654012

Used Beckman / RIIC 25 Ton Hand Hydraulic Ring Press. Rated 25 ton (50,000 pounds). Approximate 80mm (3.15") diameter platen with 100mm (3.94") working stroke. Benchtop style.

Stock# 51654013

Used Key International Bench Top High Shear Granulator / Mixer, Model KG-5. 5 Liter total volume, Stainless steel. approximately 2.4 liter working capacity. 8" diameter x 4-1/2" straight side bowl, approximate 5 liters. Bottom 3-blade propeller. Plexiglass clamp down top cover with 2" tri-clamp opening. Controls, Serial # JI-3569. R&D machine.

Stock# 51654014

Used Setra High Resolution Counting Scale, Model: Quick Count. 2500G capacity, 0.01G Readability. Serial# 723405.

Stock# 51654024

Used Pneumatech Refrigerated Air Dryer, Model ADS-500. 500 SCFM Capacity. Maximum air pressure 150 psi, maximum inlet air temp 100 degrees F., ambient temperature 55 to 100 degrees F. 2" inlet/outlet. R-22 Refrigerant, 13lb charge. Compressor driven by a 3hp, 3/60/208/230 volt motor. Fan driven by 1/15hp motor. Serial# 9804-T129020-002279.

Stock# 51708008

Used Carver AutoPellet Press, Model 3887.1SD0A06. 25 Ton maximum clamp force. 5" Diameter platen. 13MM Die. Ram stroke 1". Daylight opening 1.5 to 7.25". Mounted on a base. Serial# 110497, Built 2011.

Stock# 51708014

Used Macon Screener, 30" Diameter, 304 Stainless Steel. Single deck, 2 separation. No screen. Top clamp-on cover with 8" center inlet. Driven by a approximate 1/2hp, 3/60/460 volt, 1140 rpm motor. Mounted on a painted carbon steel base.

Stock# 51708018

Used Kawata SMB Series High Intensity Super Mixer, Type SM-B-200. 200 Liter total capacity, 120 to 140 working capacity. Jacketed chamber, 304 stainless steel. Driven by a 30hp, 3/60/460 volt, 1750 rpm XP motor. Swing away top cover with 6", 4" openings. Side bottom outlet, approximate 6" diameter with plug valve. Mounted on a painted carbon steel base. Serial# M390027.

Stock# 51816001

Used Welex High Efficiency Horizontal Cooler / Mixer. Model 1200HC, 1200 Liter Total Capacity, 316 Stainless Steel Vessel and Plows, Chrome Plated Shaft. Typical rate 2400 - 4000 lbs per hour. Approximate 26 cubic foot, 800 liter, working capacity. Cooling surface 54 square foot. Approximate 32" diameter x 99" long jacketed chamber. Approximate 5-1/4" diameter shaft with (8) bolt on "T" paddles. Driven by a 20hp, 3/60/575 volt, 880 rpm motor. Openings: (2) 36" long x 12" tall hinged doors, (2) 12" diameter, (1) 6" diameter with 2hp blower. 10" x 7" Center bottom outlet with valve. Serial# 4675 4/87.

Stock# 51818002

Used Patterson-Kelley Twin Shell Liquid-Solids Blender, 1 Cubic Foot Capacity, 304 Stainless Steel. Maximum material density 85 pound per cubic foot. (2) 11" diameter charge ports with quick release covers. Intensifier bar driven by 1/2hp, 3/60/208-230/460 volt, 1725rpm motor. Shell driven by 3hp, 3/60/230/460 volt, 1725rpm motor. 6" Center bottom outlet with manual valve. Mounted on carbon steel stands. Serial# 258343.

Stock# 51818003

Used Barnstead International Electrically Heated Portable Still, Model A1007. Output flow rate capacity 0.5 gallon per minute (1.9 LPH). Cooling flow rate 4 gallons per hour. 1.4 kW heater. Approximate 6" diameter x 12" straight side with sheathing. Mounted on carbon steel frame. UL Listed. Serial# 919031256004. 1/60/120 Volt, 12 Amps.

Stock# 53060003

Used Budsorter 24" Diameter Screener, Model Small, Stainless Steel. Double Deck, 3 separation. 24" diameter screens. Driven by approximate 1/2hp motor. Includes Budsorter variable speed controller. 3/60/240 Volt requirements. Mounted on base with casters. Serial# 0016, built 2017.

Stock# 53364001

Used Process Engineering Inc Cryogenic Storage Tank, 50,000 Gallon, Model H57740-8, Horizontal. For LOX/ Liquid oxygen or nitrogen. Approximately 10' 5.375" diameter x 86' 2.6875" straight side. Elliptical 2:1 heads. Internal rated 76 psi at -320 to 100 degrees F. Openings: 3.5" bottom fill, 4.5" vent & safety, 3.5" top fill, 4.5" liquid withdraw, 4.5" dip tube withdraw, 3.5" P.B. vapor return. Saddle mounted. National Board# 10147, Serial# C-10094.

Stock# 53364005

Used Process Engineering Inc Cryogenic Storage Tank for LOX, Approximate 1,600 Gallon, Model V-1600-7-150, 304 Stainless Steel, Vertical. Approximate 60" diameter x 102" straight side. Elliptical 2:1 heads. Internal rated 150 psi w/ext. vac at -320 to 100 degrees F. Mounted on legs. National Board# 10143, Serial# C-10294. Vacuum 258 Micron

Stock# 53364006

Used Cryo Tank Process Engineering 1,600 Gallon for LOX, Model V-1600-7-150, 304 Stainless Steel, Vertical. Approximate 60" diameter x 102" straight side. Elliptical 2:1 heads. Internal rated 150 psi w/ext. vac at -320 to 100 degrees F. Mounted on legs. National Board# 10144, Serial# C-10394. Vacuum 250 Micron

Stock# 53365001

Unused- Griffith Consulting Thermal Oxidizer, Natural Gas, Horizontal. 1500 scfm air requirements. 1.4kg/hr Combustible Compounds. 2.5MM Btu/hr maximum burner capacity, 1450F operating temperature. New and delivered: June 2023. More information to follow.

Stock# 53587001

Unused- Tarmac Int. Inc Heat Exchanger, (Never set up on the Hot side). Model 48-30DPL48-0.625-IU. 768 sqft. Stainless steel. Size: 48"*48"*54.25, CFM: 8100 CFM. Material: High temperature SST, Surface area: 768 Ft square. Total heat transfer rate: 1.8 MMBTU/Hour. Type: Plate/plate heat exchanger. Max Temp Hot Gas Inlet: 662 F. Efficient: 64.3%. Suitable to handle particulate gases from solid combustion and also applicable in clean combustion Outlet temp hot side: 249F , 11 GA. 304 S.S. casing with 18 GA. 304 S.S. expansion joints at 3 connections, 12 Ga. C.S. cladding with 3 x 3 x C S flanges primed and painted. STRUCTURAL STAND EQUAL TO OR LESS THAN 5 HEAT EXCHANGER ELEVATION. Year 2021.

Stock# 53588001

Unused- Alfa Laval Lynx 500 Centrifuge. Bowl Maximum main speed: 3250 rpm Bowl length: 2247 mm, Bowl diameter: 510 mm, Beach angle: 6, Solids discharge type: 8 wear liners - 360-type Solids transportation aids. Cylindrical section: 24 AISI 316 ribs. Solids transportation aids, taper section: 24 Stellite ribs Material - hubs: AL 111 2329-83 (Duplex stainless steel) Material - bowl shell: AL 111 2329-83 (Duplex stainless steel) Material - bolts: A4 (AISI 316) Material - seals: Liquid outlet, type: 6 Liquid outlet, radius: 147 mm (fitted from factory: 147 mm) Conveyor Material - flights: AL 111 2349 (AISI 316) Material - hub: AL 111 2349 (AISI 316) Wear Protection Bowl solids discharge: Wear liner in tungsten carbide covering the outer diameter of the spoke, 8 pieces. Wear ring fully covered by Tungsten Carbide wear segments Part No. 61244668-80 Bowl feed zone liner: Conveyor flights: Tungsten Carbide Tiles / TM42 (flame sprayed tungsten carbide) Conveyor feed zone: Tungsten Carbide wear liner

Stock# 53656001

Used Fitzpatrick Fitzmill, Model DASO6 Hammer Mill, Stainless Steel. Capacity up to 749 lbs/hr, 1000-4600rpm speed range. Approximately 15" x 15" x 10" deep feed hopper, fed by an approximate 2-1/2" diameter x 58" long screw. Driven by a .33hp 3/60/208-230/460 volt, 1725rpm gear motor, 4.88:1 ratio. Approximately 11-1/4" long x 6" wide x 16" deep milling chamber. (16) Fixed blades, Blunt & knife edge 1" wide x 3-3/4" long x 1/2" thick. Driven by a 7.5hp 3/60/230/460 volt, 1760 rpm motor. Approximately 9-1/2" long x 5-1/2" wide bottom discharge, with screen. Mounted on a stainless steel frame with casters. Serial# 7964.

Stock# 53719002

Used Friulair Chiller, Model CWM003-UE. 0.71 Ton nominal capacity. V0.013 gallon Refrigerant Circuit, R407C with 33.51 oz charge. Serial# 130021582.

Stock# 53750001

Used Baltimore Aircoil Series 1500 Cooling Tower, Model 15201-2, (2) Cell Unit. Nominal 201 Ton rating each cell, 402 total tons. Nominal flow rate 1206 GPM, maximum flow rate 1992 GPM. 6" Inlets, 8" Outlets. (2) Approximately 15HP Fans. Airflow: Approximately 53,450 CFM (per cell).

Stock# 53756001

Used Atlas Copco Rotary Screw Air Compressor, Model GA45. Air cooled; rated 294 cfm at 107 psi; 107 psig max. discharge pressure; Elektronikon control panel. Driven by a 60 hp, 3/60/230/460 volt, 3550 rpm motor. 17537 load hours.

Stock# 53756003

Used Industrial Rotary Screw Air Compressor, mfg by Atlas Copco, Model GA45. Air cooled; rated 294 cfm at 107 psi; 107 psig max. discharge pressure; Elektronikon control panel. Driven by a 60 hp, 3/60/230/460 volt, 3550 rpm motor. 9,504 load hours.

Stock# 53833001

Used Parkinson Duplex Slitter/Rewind, Model 845. 3.94"-63" slit width ranges; 48" unwind diameter; 38" min. core; 72" max. core; 5000 lbs. max roll weight; 0.5-2.5 pounds/linear inch tension control. Winding station: 40" max. winding diameter; 72" shafts max. web; 0.5-2.5 pounds/linear inch tension. Shaftless floor-lift unwind; Allen Bradley PLC; Red Lion 15" touch screen monitor; Yaskawa A100 drives. 20 HP unwinder and winder motors; 15 HP main roll motor. 3/50/400VAC. Built 2017. Previously used for 35-70 micron PVC and PETG heat shrinkable film. With Dalmec shaft remover.

Stock# 53863001

Used Gongyi Guoxin Machinery Mesh Belt Dryer, Model GX12. 83 sq. meters (893.4 sq. ft) drying area; 2000mm wide x 12000mm 4 layer stainless steel mesh belt; 400kg /h input capacity. After harvest if the hemp is small size powder the capacity will be higher; Input moisture 85% and output moisture 10-12%; Dryer needs 29kg/h propane; 0-120 degrees C adjustable dryer temperature. Includes: Diesel heat furnace, Model Z1650; 1800mm wide x 6000mm long stainless steel feeding conveyor, Model GX800x6; 300mm wide x 4000mm long discharge conveyor, Model GX-800-9; Control panel. Serial # GXDM-1903102, New in 2019. Last used dry industrial hemp.

Stock# 53907001

Used Spray Drying Plant including: Bowen 16' Spray Dryer Technical Data: Feed Rate: 3400 lbs/hr, Feed Solids: 50.0%, Feed Temperature: 50F, Evaporation Rate: 1575 lbs/hr, Powder Rate: 1800 lbs/hr, Product Moisture: 5.0%, Inlet Temperature: 430F, Outlet Temperature: 305F, Ambient Temperature: 50F, Plant Elevation: Sea-level, Fuel Consumption: 7.0 MM Btu/hr, Power Consumption: 225 kW. Includes the following: (1) Bowen 16' Spray Dryer, Spray Chamber (CH-1010), Spray Machine (SM-1011), (1) Burner (B-1000), (1) Cyclone (CY-1020), 396-7/16"H x 99" ID (D-46024), (1) Rotary Valve (RV-1021), (1) Rotary Valve Motor (M-1021), (1) Venturi (V-1033), (1) Conveying Fan (CF-1050), (1) Conveying Fan Motor (M-1050), (1) Product Cyclone (CY-1061), 128"H x 30"ID (D-46395), (1) Product Cyclone Hopper 2000 Lb. (PH-1060), (1) Rotary Valve (RV-1062), (1) Rotary Valve Motor (M-1062), (1) Screen (SC-1081), (1) Scrubber Pump (P-1032), (1) Scrubber Pump Motor (M-105), (1) Recirc Tank (L-1031), (1) Wet Scrubber (WS-1030), (1) Main Fan (F-1035), (1) Main Fan Motor (M-103), (1) Duplex Strainer (ST-1072), (1) Water Tank (T1071), (1) Flow Meter (FM-1322), (1) Feed Pump (P-1070), (1) Feed Pump Motor (M-1070), (1) Dryer to Cyclone 36" Duct Assy (D-46390), (1) Cyclone Pot Weldment (D-46025), 122-13/16"H x 69-1/2"ID, (1) Cyclone to Scrubber 36" Duct Assembly (D-46393), (1) Cyclone to Scrubber Duct, Venturi Duct (D-46396), (1) Scrubber to Fan Ductwork - GA (D-46400 & D-46401), Cyclone Explosion Relief Panel Assy (D-46440, -46441, -46442 & -46445), Spray Drying Access Platforms - Framing Plans (8', 13' & 16' Elev.) (D-46459), Spray Drying Access Platforms - Framing Plan (22'-10" Level) (D-46471), Spray Dryer Access Platform - Column & Bracing GA (D-46472 & D-46473), Spray Dryer Access Platform - Framing Plan (26'-3.75" & 28'-2" Levels) (D-46474), Spray Dryer Conveying Duct Venturi (D-46480), Spray Drying Access Platforms - Framing Plan (33'-2" Elev.) (D-46505), Spray Dryer Access Platform - Framing Plan

Stock# 53930004

Used ICC NorthWest Single wall Stainless Steel Mixing Tank, 4,224 Gallon, 304 Stainless Steel, Vertical. Approximate 90" diameter x 144" straight side. Flat top, dished bottom. Internal rated ATMOS at -20 to 200 degrees F. Top agitator bridge with 4-tier impeller blade on approximate 2" diameter shaft (bottom supported), no drive. (3) Sidewall baffles. 2" Center bottom outlet. Side lug mounted.

Stock# 53930007

Used ICC Northwest 4,605 Gallon Single wall Stainless Steel Mix Tank, 316L Stainless Steel, Vertical. Approximate 99" diameter x 132" straight side. Flat top, dished bottom. Internal rated ATMOS at -20 to 200 degrees F. Top agitator bridge with 4-tier impeller blade on approximate 2-1/2" diameter shaft (bottom supported), driven by 5HP gear motor. (3) Sidewall baffles. 2" Center bottom outlet. Side lug mounted.

Stock# 53930013

Used ICC NW Inc Single wall 35,000 Gallon Stainless Steel Vertical Silo, 304 Stainless Steel. 14' Diameter X 30' - 3" straight side. Off center agitator bridge with top entering agitator. Openings top head: 18" manway, 6" vent, 6" for agitator, (2) 2" inlets, sidewall: 24" manway, shell: 4" inlet, 4" drain port. Cone top, Slope bottom. 2022.

Stock# 53930014

Used HEI/ Hoffland Environmental / JWF Filtration Filter Press, Model X10AZGF100/1250-UK. Approximate 1,000 square feet, 65 cubic feet capacity. Approximate (40) 49" x 49" x 3" thick (1250mm) polypropylene recessed filter plates. Automatic plate shifting, drip tray. Powered by HEI Hydraulic Power Pack, Model YZA-02L-HD,40 Gallon, 5.5KW power, 4000 PSI nominal Pressure. 4" Center Feed. 2-1/2" 4-Corner discharge. Includes filter press mounted control panel with Allen Bradley Micro850 PLC, A/B panelview HMI. Drive control panel control with (3)Yaskawa P1000 drives. Built 2022.

Stock# 53937002

Used Niro Utility Spray Dryer, Stainless steel. With Atomizer. S/n 7916.

Stock# 53945001

Used Battenfeld 80mm Extrusion Line. Consisting of: Battenfeld Fischer 80mm, 26:1 L/D single-screw extruder with (5) 1300W heating zone barrel. Includes: Stainless steel cooling bath (12' L x 3' W); Approx. 300kg/hour strand cutter; Xiecheng 3 kW, 200kg drying hopper; Oil pump cooling system; Medium die (w/ manual screen changer); Small die (without screen changer). Driven by Emerson 3ph, 1185 RPM, 50 HP motor with a Zahnradwerk Kullmann PEZS gearbox, rated 33 Kw; ABB ACS550-01-072A , 3ph, 37/30 kW drive.

Stock# 53953001

Unused- United Pumps Australia 2 Stage Process Pump, Model DSTHF 2. Two stages for moderate head applications, double-entry first-stage impeller to suit low NPSHA cases. Both top suction / top discharge (on the same side). Type: 8 x 14 DSTHF x 2 STAGE. Flow rate: 339 m3/hr Head: 263.65 m Max Speed 2975 rpm Casing: P.T 7,585 kPag MAWP: 3,790 kPag @ 350C max Radial BRG: 834-42 Thrust BRG: 7311 BECBM Features: Modern API 610 Seal Chambers. Inpro VBX bearing shields. Fan (air) cooled bearing frames. Skid mounted. Designed for high suction pressure pipeline and process services. New in 2018.

Stock# 53953002

Unused United Pumps DSTHF 2 2-Stage Process Pump 339 m/hr, 263.65m Head, Skid Mounted. Two stages for moderate head applications, double-entry first-stage impeller to suit low NPSHA cases. Both top suction / top discharge (on the same side). Type: 8 x 14 DSTHF x 2 STAGE. Flow rate: 339 m3/hr Head: 263.65 m Max Speed 2975 rpm Casing: P.T 7,585 kPag MAWP: 3,790 kPag @ 350C max Radial BRG: 834-42 Thrust BRG: 7311 BECBM Features: Modern API 610 Seal Chambers. Inpro VBX bearing shields. Fan (air) cooled bearing frames. Skid mounted. Designed for high suction pressure pipeline and process services. New in 2018.

Stock# 53953005

Used Jenbacher JGS-416 GS-N L Natural Gas Generator 1203 kW, 50Hz, Built 2018. Rated COP 1203kW; Power factor of 1; Jenbacher J416 engine; 1500 RPM, 50hz/400V. With controls. Built 2018. Reported to have approx. 23,000 Hours.

Stock# 53953006

Used Jenbacher 1203 kW Natural Gas Generator Set J416 Engine, 50Hz, Built 2018. Rated COP 1203kW; Power factor of 1; Jenbacher J416 engine; 1500 RPM, 50hz/400V. With controls. Built 2018. Reported to have approx. 23,000 Hours.

Stock# 54019001

Used 6" Stainless Steel Pope Scientific Cannabinoid Distillation System. System consists of: 6" molecular still complete with variable speed drive mechanism; self-supporting still stand; SS still body; SS internal condenser 6L glass graduated feed and degasser flask w/ stopper; 5L glass distillate receiver flask; 5L glass residue receiver flask; glass cold trap; 316 SS wiper retainer; Teflon wiper blades; all necessary glass to SS adapters. Includes: Metal band heater set for 6" SS still body w/ high temperature cordset ceramic insulators; J" thermocouple and insulating jacket installed for temperatures up to 707 degrees F (375 degrees C) 50/240V; digital temperature controller with automatic tuning of proportional band; integral time and derivative time parameters, setpoint. and process displays; 500 ml receiver flask for smaller batches; 1000 ml receiver flask; (2) 2L receiver flask; (2) five liter receiver flask; external condenser with 24/25 stopper for 6" still; (4) heat controller for noncritical feed/degasser. 50/60/120V. Built 2019.

Stock# 54019002

Used Pope Scientific 6" Stainless Steel Cannabinoid Distillation System. System consists of: 6" molecular still complete with variable speed drive mechanism; self-supporting still stand; SS still body; SS internal condenser 6L glass graduated feed and degasser flask w/ stopper; 5L glass distillate receiver flask; 5L glass residue receiver flask; glass cold trap; 316 SS wiper retainer; Teflon wiper blades; all necessary glass to SS adapters. Includes: Metal band heater set for 6" SS still body w/ high temperature cordset ceramic insulators; J" thermocouple and insulating jacket installed for temperatures up to 707 degrees F (375 degrees C) 50/240V; digital temperature controller with automatic tuning of proportional band; integral time and derivative time parameters, setpoint. and process displays; 500 ml receiver flask for smaller batches; 1000 ml receiver flask; (2) 2L receiver flask; (2) five liter receiver flask; external condenser with 24/25 stopper for 6" still; (4) heat controller for noncritical feed/degasser. 50/60/120V. Built 2019.

Stock# 54041001

Used SPX APV Gaulin UHT Homogenizer, Model 185Q-4.7P, Stainless Steel. Rated capacity 18,000 L/H (4,755 GHP). Intake pressure: 3-10 bar (43 - 145 psi). Max operating pressure 12 bar. Working temperature 5 - 85 degrees C., max temperature 160 degrees C. (45min/24 hours). Outlet pressure 25 bar (363 psi). Driven by a 200 Kw / 268 HP motor. 50 Hz. ideal for use in the food, beverage, cosmetic, etc. Industries. Spare parts available at extra cost.

Stock# 54129001

Used PET Sheet Extrusion Line 48" Wide, 2,000 lbs/hr, OMV D140 Extruder (Used) 350 HP main motor; 30 HP drive system; Rated up to 2,000 lbs/hour (dependent on material and configuration); Multi-zone cooling rolls; Chrome-polished roll stack. OMV Single Screw Extruder, Model D140 6P. 6" diameter. SN 01087; 3/60/480V. Built 2001. With Operating panel, Conveyor, Draw rolls, Temperature control system, Chiller, Vacuum loader, and Winder/accumulator.

Stock# 71998001

Used Delkor Top Seal Carton Closer for Coffee Pods or K Cups. Capstone Series, Model FSC. For single forward flap glue closing is ideal for display cartons or coffee pod cartons. Capable of maximum speed of 55 cartons per minute, depending on application. Maximum Carton size range: up to 20" (length) x up to 14" (width) up to 14.5" (height). Last running cutlery. Uses Allen Bradley Compact logix PLC controls with Allen Bradley Kinetix Servo motors, and an Allen Bradley Panelview-Plus 700 HMI. Equipped with a Nordson ProBlue-10 Hot Melt Glue Applicator. 3/60/480V. Ideal for K-Cup Style Coffee Pods.

Stock# 72519001

Used CTM Front & Back Labeling System. Consists of (2) CTM Model 3600-PA printer applicator with Sato M-8460Se print engine. Maximum width: 6" x 49.2" long. Media size: 2" wide x 0.24" long minimum, 6.5" wide maximum. Print resolution: 203dpi (8 dots/min). Belt conveyor 12" wide x 95-1/2" long. Fanuc 2k Series Control. 1/60/120 Volt, 15 amps.

Stock# 72922001

Used Shanklin CF3 Automatic Side Seal Shrink Wrapping Machine; Up to 30 packages per minute; Package size: Minimum: 7.5 inches long x 11 inches wide x 1/16 inches tall; Maximum: 120 inches long x 30 inches wide x 10 inches tall; Maximum film width: 36 inches; Seal bar width: 33 inches; Infeed: 47 inches long x 29 inches wide; Outfeed: 43 inches long x 29 inches wide; Includes: Selvage Winder; Automation Direct HMI; Touchscreen Operator Interface; Extended In-Feed Conveyor; Sealed Air Dual Wire to Hot Knife Side Sealer. HMI needs updated software.

Stock# 73074001

Used World Cup Rotary Cup Filler, Model 8-12. Capable of up to 40 cups/minute. Capable of cup sizes 1oz-10oz. Max. cup diameter 81mm. Currently tooled for 75mm cup with 79mm lid. 5 gallon conical hopper. Mounted on casters. Previously used for apple sauce. Built 2020.

Stock# 73157001

Used Hayssen Model Ultima CMB Coffee MAX Vertical Form Fill and Seal Machine with All-Fill Model Powder Auger Filler. Capable of speeds up to 40-60 pouches per minute (depending on product and pouch size). maximum pouch size: 8" (width) x 12" (length) Equipped with 12.5" tall vertical sealer & 9" wide cross seal jaws. Includes Markem date coder.

Stock# 73308001

Used Tishma Model Flex 7 (ROO-100) Premade Pouch Filler and Sealer. Capable of speeds up to 40 PPM. Has a pouch size range: 4"-16" (width) x 6" - 21" (height) x 0" - 6" (thickness). Weigh Right PMB4 L linear scale and elevator with a weight range from 2 oz- 10lbs. Allen Bradley CompactLogix PLC with Panelview HMI, Video Jet Model 1580 Ink Jet Date coder. Last running 10 and 18oz IQF frozen food products. Includes Weigh Right PMB4 Linear Scale and Bucket Elevator,

Stock# 73332001

Used Chart Ultradoser Model FS150. Capable of speeds up to 150 CPM. The UltraDoser 150S LN2 Dosing System is a multipurpose liquid nitrogen dosing system utilizing advanced cryogenic technology and PLC programming. LN2 is supplied to the UltraDoser unit by a vacuum insulated hose and flows into the dosing head. A sensor detects the speed of the line (encoder compatible); a second sensor detects the presence of a container. When a container is detected, the dosing head opens and dispenses an exact amount of pure LN2 . A PLC (Programmable Logic Controller) is the brains behind integrating the sensors, controls and human interface. Last used in Cannabis

Stock# 73363001

Used Palmer Canning Systems Craftbloc 12/1 Can Filler and Seamer. 12 valve counter pressure filler; 28-50 cans per minute; Allen Bradley PLC control for entire system and synchronization of filler, seamer, and can conveyance; Heavy duty seams preserve high CO2 retention; Seaming tooling, titanium carbide and nitride coated rolls and chucks with ceramic bearings; Mechanical cam-driven seaming, heavy-duty, Continental 450; Undercover gas manifold. Fills standard, sleek, and slim cans; filling accuracy 5 grams (5 ml); Max CO2 volume 3.5 V/V (Beer 2.0-3.0); 3/60/230 volt; CO2 consumption 6-10 CFM at 60 psi.

Stock# 73435001

Used Moravek Carbonated Beverage Filling Line, Model BC15 + 12/12/1. Includes Tribloc filler with 12 oz and 22 oz changeover parts. Filler includes pre-filter valve cluster including vacuum pump, rinser infeed and peracetic doser, conveyance for infeed and outfeed. We also have misc spare parts. Last used on craft-style beer. New 2014. 3/60/480V.

Stock# 80051

Used Patterson Kelley Twin Shell Blender, 50 Cubic Foot, 304 Stainless Steel. Rated 55lbs. per cubic foot maximum material density. Standard feed ports with covers, 10" diameter discharge with butterfly valve. Driven by approximate 5 hp drive with brake. Mounted on stands with 90" discharge height. Serial # 249510.