Price Recently Reduced Process & Packaging Equipment Inventory

Stock# 14191146

Used Crown Iron Works, Model 48, Milling Ring Flash Drying System. It was designed and used for food-grade orange pulp with 17,000 Lbs/Hr capacity but the plant can be used for a wide range of applications in various industries including: Drying food products such as grains, cereals, fruits, vegetables, herbs, and spices. Pharmaceutical ingredients, intermediates, and final products Drying various chemicals, including powders, granules, and crystalline materials Drying minerals and mining products such as ores, concentrates, and mineral powders Animal Feed Drying and processing environmental materials, such as sludges, biomass, and waste products. System designed for drying of powers, filter & centrifuge cakes, and slurries where a discrete and fine end product is desired. The Milling Flash Dryer is basically a low energy jet mill, that uses jets of low-pressure air to encourage inter particle collisions between pieces of feed material. These inter particle collisions break up the feed material in the dryer with no moving parts in the dryer or airstream. The dryer is in the shape of a torus, or donut that is broken up into 2 basic areas: (1) Manifold & Milling area; (2) Classifier. The ideal feed material for the Flash Dryer is a crumbly and free flowing cake that breaks up readily when it enters the drying air stream. The feed material enters the recirculating hot air upstream of the first nozzle, with the centrifugal forces generated by the air concentrating the material in the area above the nozzles. Particle-to-particle collisions begin immediately, deagglomerating the material before hard agglomerates can form. A tremendous amount of surface area is created allowing evaporation to occur quickly, thereby depressing air temperature in a very short period of time. Centrifugal forces are generated by the recirculating gases within the dryer, forcing the larger particles to the peripheral walls. Finer material is displaced towards the inside radius of the dryer where the classifier outlet is located. Fine product exits the dryer along with the exhaust gas vapor. Larger particles or agglomerates are recycled to the nozzle area dryer for further de-agglomeration and drying.

Stock# 409353

Used Hobart Model H-600-T Mixer. 60 Quart capacity. Approximate 18" Diameter X 16" deep bowl. Driven by a 1hp. 3/60/208 Volt, 5.9 Amp motor. Manual tilt. Serial# 1814053.

Stock# 47083001

Used Flottweg Z5L Solid Bowl Horizontal Decanter Centrifuge. 316/329 Stainless steel construction (product contact areas), maximum bowl speed 2650 rpm, single lead conveyor with welded hardfacing, cyclo gearbox, stainless steel discharge chutes, standard feed pipe, grease lubrication system, adjustable liquid plate dams, fiberglass bowl cover, base, 55 kw, 380/3/50 main drive.

Stock# 47200002

Used Alfa Laval Solid Bowl Decanter Centrifuge, Model AVNX-616B-31G, 316 stainless steel (product contact areas). Maximum bowl speed 3250 rpm, single lead conveyor with welded hardfacing, moon liquid plate dams, base, casing with cake vibrator, feed pipe, 2.5 Knm gearbox, 11Kw 380/3/50 main motor.

Stock# 50823014

Used Schutte-Buffalo-Astec Hammermill, Model AHM-20, Carbon Steel. Approximate (2) 48" diameter x 24" wide rotors. 2-3/4"w x 4"L x 5/16" thick swinging hammers, approximately 7 rows of (14 hammers) 2 sections, 3/16" screen. 15"W x 60" Long Top feed with hopper, 60-1/2"L x 11"T bottom discharge. Driven by a 600 HP, 3/60/460 volt, 1790 rpm motor. Mounted on a frame. Includes a Twin City blower, Type RBR-SW, size 926, driven by a 200 HP, 3/60/230/460 volt, 1785 rpm motor.

Stock# 50823042

Used Schutte-Buffalo-Astec Model AHM-20 Hammermill, Carbon Steel. Approximate (2) 48" diameter x 24" wide rotors. 2-3/4"w x 4"L x 5/16" thick swinging hammers, approx 7 rows of (14 hammers) 2 sections, 3/16" screen. 15"W x 60" Long Top feed with hopper, 60-1/2"L x 11"T bottom discharge. Driven by a 600 HP, 3/60/460 volt, 1790 rpm motor. Mounted on a frame. Includes a Twin City blower, Type RBR-SW, size 926, driven by a 200 HP, 3/60/230/460 volt, 1785 rpm motor. Astec Serial # 16-085-299260-22-1.

Stock# 50823043

Used Schutte-Buffalo-Astec Carbon Steel Hammermill, Model AHM-20. Approximate (2) 48" diameter x 24" wide rotors. 2-3/4" wide x 4" long x 5/16" thick swinging hammers, approximate 7 rows of (14 hammers) 2 sections, 3/16" screen. 15" wide x 60" long Top feed with hopper, 60-1/2" long x 11" tall bottom discharge. Driven by a 600 HP, 3/60/460 volt, 1790 rpm motor. Mounted on a frame. Includes a Twin City blower, Type RBR-SW, size 926, driven by a 200 hp, 3/60/230/460 volt, 1785 rpm motor. Astec Serial # 16-086-299260-22-1.

Stock# 50823099

Used Schutte-Buffalo-Astec Model AHM-20 Carbon Steel Hammermill. Approximate 48" diameter x 50" wide rotor. Top feed with hopper, bottom discharge. Driven by a 600 HP, 3/60/460 volt, 1790 rpm motor. Mounted on a frame. Serial# 16088HM1. Includes a Twin City blower, Type RBR-SW, size 926, driven by a 200 HP, 3/60/230/460 volt, 1785 rpm motor. Astec serial# 16088HM1.

Stock# 50907002

Used Stephan Cutter / High Speed Universal Horizontal Vacuum Mixer, Stainless Steel. Jacketed 29" diameter x 17" deep SS bowl. Hydraulic slide gate discharge 12" x 10". Driven by a 15 kw drive, with Stephan Stainless steel hopper 32" x 12" straight side x 22" cone. Pneumatic butterfly valve, Stephan incline discharge conveyor, 24" wide x 80", discharge, with control panel. Serial # 718781. No tag on the Mixer, but it appears to look like a Model TK150. Used for Dough/ Bakery.

Stock# 51354004

Used Westfalia NA-7-06-076 Desludger/Nozzle Disc Centrifuge, stainless steel construction (product contact areas), max bowl speed 8510 rpm, clarifier design (liquid/solids separation), centripetal pump liquid discharge. Flanged mounted drive motor, 7.5hp, 230/460/3/60 volt drive motor. Cart Mounted. Control panel with A/B microview, A/B micrologix 1000 PLC.

Stock# 51658003

Used Conair Tempro Portable Air Cooled Chiller, Model AC1-10. Approximate 11 Ton Capacity. Approximate 47 gallons per minute at 36 psi. Operating temperature 20 - 65 degrees F. Compressor 10hp, R-22 refrigerant. Process pump 1.5hp, (2) 1hp fans. Approximate space heating capacity 171. 10,000 CFM. 2" Connections. Mounted on casters. Serial# 95A025. 3/60/460 Volt.

Stock# 52315001

Used Erema Edge Trim Plastic Recycling Line, Type KAG 605. Capacity of 66-220 pounds/hour (30-100 Kgs/hour). Consisting of (1) Erema compactor including 11 kw motor and product feed, (1) Erema single screw extruder, 1.95" (50 mm) diameter, non-vented barrel, 11 Kw drive/motor. (1) Underwater pelletizer. Control panel with Siemens AC drive and Siemens micromaster 440 drives. Frame mounted. Serial# P07/220. Previously used in a blown film line to recycle the virgin material back into the production again.

Stock# 52862007

Used Anhydro Vertical Heat Exchanger / Reboiler, Approximate 31.8 Square Feet. Carbon steel shell rated 100psi / FV external at -20 to 600 degrees F. (31) 1" Diameter x 47" long Hastelloy C-276 tubes rated 15 psi internal / 100 psi external at -20 to 600 degrees F. 15,000 Btu/h. Openings: (2) 2", (2) 1". Side lug mounted. Certified by Orbit Industries, National Board# 1025, Serial# 8306-PV-2. No bottom head.

Stock# 52862008

Used Anhydro Vertical Heat Exchanger / Reboiler, Approximate 31.8 Square Feet. Carbon steel shell rated 100psi / FV external at -20 to 600 degrees F. (31) 1" Diameter x 47" long Hastelloy C-276 tubes rated 15 psi internal / 100 psi external at -20 to 600 degrees F. 15,000 Btu/h. Openings: (2) 2", (2) 1". Side lug mounted. Certified by Orbit Industries, National Board# 1024, Serial# 8306-PV-1. No bottom head.

Stock# 52862009

Used Anhydro Vertical Falling Film Reboiler / Heat Exchanger, Approximate 19.5 Square Feet. Carbon steel shell rated 200psi / FV at -20 to 400 degrees F. (19) 1" diameter x 47" long Hastelloy C-276 tubes rated 15 psi internal / 200 psi external at -20 to 400 degrees F. Openings: (2) 2", (2) 1". 40,000 BTU/h. Side lug mounted. Certified by Orbit Industries, National Board# 1026, Serial# 8306-PV-3. No bottom head.

Stock# 52862010

Used Anhydro Vertical Falling Film Reboiler / Heat Exchanger, Approximate 19.5 Square Feet. Carbon steel shell rated 200psi / FV at -20 to 400 degrees F. (19) 1" diameter x 47" long Hastelloy C-276 tubes rated 15 psi internal / 200 psi external at -20 to 400 degrees F. Openings: (2) 2", (2) 1". 40,000 BTU/h. Side lug mounted. Certified by Orbit Industries, National Board# 1027, Serial# 8306-PV-4. No bottom head.

Stock# 52862011

Used Doyle and Roth Vertical Shell and Tube Heat Exchanger, Approximate 20.2 Square Feet. Carbon steel shell rated 150 psi / FV at -20 to 200 degrees F. (27) .75" diameter x 48" long Hastelloy C-276 tubes rated 15 psi / FV at -20 to 300 degrees F. Openings: (1) 4", (2) 1", (3) .75". 40,025 BTU/H. Single pass. Baffle spacing 4.125". Side lug mounted. National Board# 20734, Serial# S1989-4, 2008. No bottom head.

Stock# 52862012

Used Doyle and Roth Approximate 20.2 Square Feet Vertical Shell and Tube Heat Exchanger. Carbon steel shell rated 150 psi / FV at -20 to 200 degrees F. (27) .75" diameter x 48" long Hastelloy C-276 tubes rated 15 psi / FV at -20 to 300 degrees F. Openings: (1) 4", (2) 1", (3) .75". 40,025 BTU/H. Single pass. Baffle spacing 4.125". Side lug mounted. National Board# 20733, Serial# S1989-3, 2008. No bottom head.

Stock# 52862013

Used Doyle and Roth Shell and Tube Vertical Heat Exchanger, Approximate 20.2 Square Feet. Carbon steel shell rated 150 psi / FV at -20 to 200 degrees F. (27) .75" diameter x 48" long Hastelloy C-276 tubes rated 15 psi / FV at -20 to 300 degrees F. Openings: (1) 4", (2) 1", (3) .75". 40,025 BTU/H. Single pass. Baffle spacing 4.125". Side lug mounted. National Board# 20732, Serial# S1989-2, 2008. No bottom head.

Stock# 52862014

Used Cataract Steel Industries Shell and Tube Heat Exchanger, Model SG-33006-SETT, Approximate 21.2 Square Feet. Carbon steel shell rated 60 psi at -20 to 300 degrees F. (27) 3/4" diameter x 48" long 316L Stainless steel tubes rated 100 psi at -20 to 300 degrees F. Openings: (2) 6", (2) 2", (2) 3/4". Side lug mounted. National Board# 4639, Serial# 33006, built 2013. No top or bottom heads, Flange cut on one side.

Stock# 52862016

Used Doyle and Roth Vertical Shell and Tube Condenser, Approximate 19.6 Square Feet. Carbon steel shell rated 150psi / FV external at -20 to 400 degrees F. (55) 3/4" Diameter x 24" long Hastelloy C-276 tubes rated 15psi / FV at -20 to 450 degrees F. Approximate 12,733 BTU/h.Single pass. 3.875" Baffle spacing. Side lug mounted. National Board# 20736, serial# S1993-2.

Stock# 52862017

Used Doyle and Roth Vertical Shell and Tube Condenser, Approximate 18 Square Feet. Carbon steel shell rated 150psi / FV external at -20 to 300 degrees F. (50) 3/4" diameter x 24" long 316L Stainless Steel tubes rated 15 psi / FV at -20 to 350 degrees F. Baffle spacing 3.5". Single pass. Side lug mounted. National Board# 20757, Serial# S1998.

Stock# 53061015

Used Rotex Screener, Model 242A ALSS, 2 Surface Model. 8 Square Foot Nominal area per surface. 304 Stainless Steel, 24" wide x 48" nominal screen size per surface (in.). Bottom stainless steel deck has 3/8" diameter holes. Aluminum cover with a 10", and 3-1/2" opening. Driven by a 1hp 3/60/208-230/460v 1730rpm motor. (2) 3-1/2" end bottom discharges, with 50" discharge height. Serial# R210886. Mounted on a carbon steel frame. Upper WT 102. Lower WT 46.

Stock# 53102001

Used Vitalis Extraction Technology Model R200 CO2 Extraction System. 2x100L extraction vessels, accumulator skid, Hydraulic power unit, HMI control panel, R200 catwalk. Refrigeration condenser is not included. Working Condition.

Stock# 53102002

Used Vitalis Extraction Technology Model Q90 CO2 Extraction System. 2x45L extraction vessels, accumulator skid, Hydraulic power unit, HMI control panel. Refrigeration condenser is not included. Working Condition.

Stock# 53207001

Used Flottweg Tricanter Seperator, Model Z23-4/941. Stainless steel. Maximum 5000 rpm bowl speed. Maximum sediment density 2.3 kg/dm3. Product temperature 0 - 40 degrees C. Missing drives. Control panel. Seral# 00219315. 3/60/460 Volt, 42 Amp.

Stock# 53207003

Used ICS Chillers Air Cooled Condensing Unit, Model ICS-15ACCUD-HA-460. Approximate 15 nominal tons. Serial# CYC-15D46-1008. (2) Carlyle Model 06DG8252BA3650 7-1/2HP compressors. (4) 1HP condenser fans. Refrigerant HCFC 22. 3/60/460 Volt.

Stock# 53236001

Used ABL PDS TT 50 Apple Peeler Corer. All stainless steel. Capacity 250-500kg/hr, - 50 apple/mn. Infeed system Mod Shufflo 50 Double peeling head with "no peel" option, core tube driver with angular gear, seed cell removal system with slicing head to cut apples into segment. TT cutting device to allow to cut chunks as well as ring with min thickness 10mm. Auto grease and lube system. Includes (2) catwalks, waste conveyor, (1) peeled apple conveyor and control panel.

Stock# 53283004

Used Tecnetics Industries Dual Volumetric Tecweigh Feeder System with Hoppers. Includes (2) Tecweigh volumetric feeder with "Flex-Feed" hopper system, model E12, 1.2 cubic foot hopper capacity, driven by 3/4hp motor. Best Engineering Hooper, approximate 46" diameter. Both Feeder/Hoppers mounted on frame.

Stock# 53283005

Used Tecnetics Industries Tecweigh Dual Hopper Dual Volumetric Feeder System. Includes (2) Tecweigh volumetric feeder with "Flex-Feed" hopper system, model E12, 1.2 cubic foot hopper capacity, driven by 3/4hp motor. Best Engineering Hooper, approximate 46" diameter. Both Feeder/Hoppers mounted on frame.

Stock# 53283007

Used Tecnetics Industries Tecweigh Volumetric Feeder, Model E-28. Has Flex-Feed hopper system 2.8 cubic foot capacity. Screw approximate 6.5" diameter x 48" long. Driven by a 1.5hp, 1750 rpm motor. Serial# 8190C9902.

Stock# 53452001

Used Eirich / American Process Paddle Blender, Model PPB030, 30 Cubic Feet Capacity, Stainless Steel. Non-jacketed trough approximately 90" long x 30" wide x 39" deep. Single shaft approximate 4" diameter with (17) paddles, approximate 11.5" x 5" x 5/8" thick. Driven by a 7.5hp (5.5kW), 3/60/230/460 volt, 1755 rpm gear motor, final rpm 61. (2) Piece top hinged cover with 44" x 30" infeed section. End bottom outlet 8" x 8" with slide gate valve. Mounted on (4) legs. Serial# 807495, Built 2016. Last used in shredded cheese application. 3/60/460 Volt.

Stock# 53534001

Used Goodnature Juice and Cider Press, Model SX280. Rated for output of up to 450 gallons/hour (1700 liters/hour), 2-3 tons/hour; Press features "squeezebox" design plates constructed of stainless steel; On/Off and Forward/Reverse Controls; 1/50/380VAC. Includes: Stainless steel Fitzmill type mill; Auger pump and pomace pump; Custom built pasteurisation bath, fully insulated and 100% food grade stainless steel. This model is designed for running hard vegetables, leafy greens, most fruits and nuts for plant based milks (i.e. apple, kale, pineapple, spinach, almonds and other nuts, beets, celery, carrot, herbs, lemons and much more).

Stock# 53642001

Used Lot of (8) Evapco Eco-ATWB 24-4N20 Closed Circuit Cooling Towers. Approximately 600 ton each. Each approximate 2,800 GPM. (2) 40hp fans, approximate 281,190 CFM. Coil volume 5,107 liters (1349 gallon). (2) 40HP fans. Setup as (2) cell units. Seller would like to sell all 8 units at one time, however, will accept offers. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.

Stock# 53651001

Unused Selmi Spider Vertical Spiral Cooling Tunnel. 304 stainless steel contact parts; Holds 120 moulds. Has 40mm clearance for product. Angular air distribution; Possibility to choose whether to work in continuous or with work / pause; Belt speed adjustable via comfortable and intuitive touch screen; In original packaging; New in December 2023.

Stock# 53690001

Used Belshaw Adamatic Double Rack Oven, Model OVEN 2020. Natural gas or propane with automatic electric switch over; 275,000 btu/hr; Stainless steel construction; Heavy duty rack lift, accepts A, B, or C-styles, 46" long B-style lift, with spare lift for (2) B-style single racks; 39" wide x 75" tall door; 10" diameter exhaust, with 10" to 12" diameter adapter; Dayton 12" diameter exhaust fan; Oven is 72" wide x 62" long plus 30" long exhaust hood; Stainless steel floor insert; Natural Gas or Propane (Electronic automatic switch over). 3/60/208/240V New in May 2019.

Stock# 53748001

Used Gloe Corporation Mobile Extraction System. Recovery rates of 2 gpm at only 160f and 25"hg (more heat + more vacuum = faster recovery) ability to recirculate to further concentrate crude. Can batch 100lbs of ground material or about 60lbs flower at a time. Easy production of oil; Easy scalability; No building required; Automated cryoethanol extraction system.120 gallon batch tank; 4 stage filtration/remediation system; 300gallon vacuum jacketed cold storage tank; 300 gallon hot water jacketed tincture tank; 4 - 70"by 10" 150 tube falling film evaporators (3,500+sqft of surface area!) automated and manifolded together; 300 gallon reclaim tank. Designed and built by experienced process food/beverage system builders; All stainless sanitary build out; Welded by certified welders and passivated after fabrication for safe consumption products. Utilities included: 1;000;000 BTU water heater system; 40t cooling tower; Becker27"hg vacuum pump; Sullair 185 scroll air compressor; mq 70kw whisper watt generator; Completer 20l rotary evaporator with vacuum pump and chiller.

Stock# 53762001

Used Sandvik Belt Flaker Cooler/ Dryer. Approximately 32" wide x 34' long. 301 Stainless steel contact parts. 24' Of cooling area. 3HP chill roll drive. 3HP belt drive. Pinch rollers feed in system. Mounted on Casters. Job # 987870.

Stock# 53762002

Used Sweco Model XS48S66TLUE Vibratory Screener, Stainless Steel. Approximately 48" inside diameter screen. Single deck, single separation. Driven by a 2.5 HP Motor. Mounted on a Carbon Steel base. Serial# 308513-A08/05.

Stock# 53762003

Used Sweco 48" Diameter Vibratory Screener, Model XS48S88, Stainless Steel. Approximately 48" inside diameter screen. Single deck, single separation. Driven by a 2.5 HP Motor. Mounted on a Carbon Steel base. Serial# 642963-B996.

Stock# 53762005

Used PPS Kemutec Industrial Air Classifier Mills System, Model 5 CMT. Cyclones- Dust Collection System, with 50 HP Blower.

Stock# 53778001

Used Fitzpatrick Fitzmill, Model VFS-D6A-PCS-LB / VFS D6-PCS-0401 Hammer Mill. Throughput rates of 200 - 1,000 kg/hr (depending on product). 10" gravity Feed hopper with 3" diameter x 18" long metering screw. 6" wide x 10" diameter Chamber with (16) 4" long x 1" wide x 3/16" thick blades on a fixed blade rotor. Direct drive. XP Controls, Allen Bradley SLC 5/03 PLC, A/B HMI, A/B Powerflex 70 drive. Stainless steel construction. Mounted on casters. Serial# 11839.

Stock# 53844010

Used Fitzpatrick Comminutor Fitzmill, Model DASO-6, Stainless Steel. (16) 1" wide x 5/16" thick x 3-3/4" long fixed knives. Approximately 6" diameter x 14" long Cutting chamber. Has gravity feed throat with pan, and bottom screen discharge with 33-1/2" discharge height. Driven by a 10hp, 3/60/208-230/460 volt, 1760 rpm motor. Control panel. Mounted on a carbon steel base with (4) legs and casters.

Stock# 53844015

Used Littleford Model DVT-130 Mixer/Reactor, Stainless Steel. 3.1 Cubic feet working capacity (4.6 total). Jacketed chamber approximately 20" diameter x 26" long, bolt-on flat hinged jacketed cover. Jacket rated 75 psi at 32 to 320 degrees F. Internal rated 100 psi / Full vacuum at 32 to 320 degrees F. Side chopper motor, driven by 15hp, 3/60/230/460 volt, 3495 rpm (not installed). Includes control panel with voltage/phase indicators, gauges, piping. National Board#4298. Serial# 41779-4298. 3/60/480 Volt.

Stock# 53844017

Used Teledyne Readco Double Arm Lab Mixer, Stainless Steel Construction. 3 Quart working capacity (4.5 quart total). Hinged top cover, with safety grate. 7/16 HD. THK, 3/8 HD D.R. Approximately 8-1/2" long x 6-3/4" wide x 7" deep jacketed vessel. Internal bowl rated 15psi. Jacket rated 150psi at 650 degrees F. Tangential sigma blades driven by a UL listed 1hp, 3/60/230/460 volt, 1760 rpm motor thru reducer 33.08:1 ratio. Manual tilt discharge. Start / Stop control panel. Serial #107322. Mounted on stainless steel cart with casters.

Stock# 53904003

Used Acquity preparative supercritical fluid chromatography. Consists of the following: ACQUITY UltraPerformance C2 ACQUITY UPC2 CM-A and CM-AUX, ACQUITY UPC2 PDA Detector, UPC2 Caffeine Standard, UPC2 and Viridis SFC Columns, ACQUITY UPC2 BEH 1.7?m 2.1 x 50mm Empower Software and Options, Waters CDS Computer Lenovo C20x, MONITOR, Lenovo ThinkVision Flat Panel. ACQUITY UPLC H-Class System ACQUITY UPLC H-Class CM Core System, ACQUITY UPLC TUV Detector, ,ACQUITY H-CLASS HEX/THF MOB. PHASE, Analytical Column Options: ACQUITY UPLC BEH C18 1.7?m, 2.1x100mm Col, Empower Software and Options: W/S, Waters CDS Computer Lenovo C20x MONITOR, Lenovo ThinkVision Flat Panel. SFC 80q, 200q 200BTq & 350: System, SFC80Q 110V Core, SFC Prep UV Sample Chemistry, Chiller, Accel 500 115V/60hz 2489 UV/Visible Detector for Prep SFC, ChromScope Workstation, RocketPort Card and Extension Cable, MONITOR, Lenovo ThinkVision Flat Panel, Low Pressure Fraction Collector, 6 Fract ACQUITY UPC2 and Viridis SFC Columns, 1 Viridis BEH 5?m 2.1x150mm Column. Like new condition

Stock# 53906001

Used Evoqua Water Technologies J-Press, Model 800G32-29-15SYLW. 313 sq. ft. total filtration area. 15 Cubic feet total volume. (29) 800mm Gasketed Co-Polypropylene plates, 32mm cake thickness. 100 psi maximum feed pressure. 3700 psi Hydraulic clamping pressure. Plate shifter; Sidebar press. 1-1/2" Diameter 4-Corner discharge. 2" Center feed. Control panel with Siemens Simatic S7-1200 CPU, Siemens Simatic HMI. Monolithic welded construction. 1/60/110-120V. Serial # F009641. New in 2019.

Stock# 53913001

Used Olson Mfg. Co. dba V-RAM Pumps Double By-Products Pumping System. (2) Identical Stainless Steel Pumps, approximately 5000 lbs/hr working capacity, with 679 max psi per each pump. 30-1/2" long x 14" wide x 15-1/2" deep infeed. Approximately 54" long trough with 11" ram head. 6" diameter outlet with gate valve, 10" discharge height. Includes Double B-Style Hydraulic Unit skid with air cooler. (2) 50hp 3/60/230/460v 1775rpm motors. Includes Control Panel.

Stock# 53968001

Used AJAX Natural Gas Boiler, Atlas A200 Series, Model: Atlas A200. Heating Surface: 42.4 sq. ft. Maximum Input: 2,000,000 BTU/hr, Output: 1,800,000 BTU/hr. Thermal Efficiency: 90%, Burner Output: 1,307,692 BTU/hr, Horsepower: 50 HP, Gross Input Pressure: 4.0" W.C. Max Allowable Working Pressure (MAWP): 160 PSIG. Honeywell Sola Hydronic control, Honeywell HMI. Voltage: 120V, 60Hz, 1 Phase, Full Load Amps: 5A, Control Voltage: 24V. Serial# 71628.

Stock# 54154001

Used Stainless Steel Vertical Storage Tank, Approximately 3800 Gallon Capacity, 316 Stainless Steel. Flat top, Dish bottom. Approximately 94" diameter x 128" straight side. Openings Top" (3) 2" 23" x 23" manway with cover. 2" Center bottom outlet, approximate 9" discharge height. Mounted on (4) Carbon steel legs.

Stock# 54219001

Used Tower Tech Model TTXL-061975 modular open circuit cooling tower rated for approximately 600 tons of cooling capacity and approximately 1,800 GPM water flow. This industrial cooling tower features fiberglass reinforced plastic (FRP) casing and basin construction, PVC fill media, drift eliminators, direct-drive axial fans, and a hot-water spray distribution system. Typical design operating conditions are 95F inlet water temperature, 85F outlet water temperature, and 78F wet-bulb ambient temperature. The unit includes removable louvers, access panels, and stainless steel hardware for serviceability and long-term use in demanding commercial and industrial environments. Built in 2008, Serial Number 2008031-01, this Tower Tech cooling tower is designed for process water cooling, HVAC condenser water systems, heat exchanger cooling loops, chemical and petrochemical plants, food and beverage processing, pharmaceutical and biotech manufacturing, plastics and injection molding operations, data center cooling, power generation auxiliary cooling, refining, distillation support, and other industrial cooling applications. This 600-ton FRP cooling tower may be a strong fit for buyers searching for a used Tower Tech cooling tower, modular open circuit cooling tower, fiberglass cooling tower, 1,800 GPM cooling tower, industrial process cooling tower, HVAC cooling tower, or high-capacity cooling tower with PVC fill and drift eliminators. Aaron Equipment freight specialists can assist with door-to-door transportation, export documentation, customs paperwork, and equipment logistics.

Stock# 54219002

Tower Tech Cooling Tower, Model TTXL-061975, Open Circuit Design / Modular fiberglass cooling tower rated for approximately 600 tons of cooling capacity. It features a fiberglass reinforced plastic (FRP) casing and basin, PVC fill media, and drift eliminators. Unit has direct-drive axial fans with a hot-water spray distribution system. Typical operating conditions are 95F inlet water, 85F outlet water, and 78F wet-bulb ambient, with a flow rate of about 1,800 GPM. The tower has removable louvers, access panels, stainless steel hardware. Serial# 2008031-02. Built 2008.

Stock# 54234013

Used Sweco 48" Diameter Vibro-Energy Separator, Model XS48S88HSTL. Stainless steel contact parts. Single deck, 2 separation. Driven by a 2.5hp, 3/60/460 volt, 1740rpm motor. No top cover. Mounted on painted carbon steel base. Serial# 188375-A01/19.

Stock# 54234014

Used Sweco Vibro-Energy Separator 60" Diameter, Model XS60Y88HSTL. Stainless steel contact parts. Single deck, 2 separation. Driven by a 2.5hp, 3/60/460 volt, 1740rpm motor. No top cover. Mounted on painted carbon steel base. Serial# 167005-A06/18.

Stock# 54234015

Used Dilling Group Control Cabinet. Batch Control System Latex Tank Farm. 480 v.

Stock# 54234017

Used Flexicon Bag / Supersack Unloader with Chain-Vey System. Approximately 25' long Chain-Vey.

Stock# 54239001

Used Grieve Model HC-550 industrial electric airflow cabinet oven designed for drying, curing, baking, preheating, heat treating, and general thermal processing applications. This Grieve HC-550 oven is rated for 30 kW electric heat input and has a maximum operating temperature of 550F. The unit operates on 460-volt, 3-phase, 60 Hz power and draws 41 amps during operation. It is equipped with a 1.5 HP largest motor load, 5 kA symmetrical short-circuit current rating, and NEMA Type 1 enclosure for basic electrical protection. Built in 2011, Serial / Electrical Drawing Number 103340A0611, this industrial cabinet oven may be suitable for manufacturing, metal parts drying, coating and paint curing, adhesive curing, plastics and composites processing, electronics thermal processing, aerospace and automotive components, laboratory heating, research and development, and other controlled heating applications. This used Grieve industrial oven may be relevant for buyers searching for a used Grieve HC-550 oven, electric cabinet oven, industrial drying oven, airflow cabinet dryer, 550F oven, 30 kW industrial oven, 460V 3-phase oven, heat treating oven, curing oven, or thermal processing oven. Aaron Equipment freight specialists can assist with door-to-door transportation, export documentation, customs paperwork, and equipment logistics.

Stock# 54253001

Used Donaldson Torit Downflo Evolution Dust Collection Unit, Model DFE2-12. Approximately 3,048 square feet filter area. (12) Filter (part# P034310), (6) valves. Includes 40 HP, 3/60/230/460 volt, 3530rpm Blower. Serial# 16863451-L1-1.

Stock# 54253002

Used VDL Industrial Products Rotary Air lock, Model B-HT350EX00. Driven by 0.37kW / 0.50 HP, 3/60/277/480 volt, 1730/15 rpm motor. Serial# U-221467/B. Built 2022.

Stock# 54253003

Used Quincy QGV-100 Variable Speed Rotary Screw Air Compressor | 100 HP | 471 CFM | Water-Cooled | 5,262 Hours, 460V/3-phase. 471 cfm max capacity, 104-110 Degrees F maximum ambient temps. Water cooling. Touchscreen controller showing 5,262 hours. Panel rating 462A with largest motor FLA 163A. Unit includes integrated cooling, enclosed sound-attenuated cabinet, and emergency stop. Displays 0 PSI at outlet at time of inspection. Serial/controller ID UTY310039.

Stock# 54253004

Quincy QGV-100 100 HP Variable Speed Rotary Screw Compressor | Water-Cooled Industrial Plant Air, 460V/3-phase. 471 cfm max capacity, 104-110 Degrees F maximum ambient temps. Water cooling. Touchscreen controller (ID UTY310038) showing 5,261 hours, 75F internal temp, and 0 PSI net pressure at time of inspection. Panel rating 468A, largest motor FLA 163A, NEMA 4 enclosure. Unit includes enclosed cabinet, emergency stop, and standard Quincy BADGER PXE control package.

Stock# 54253005

Used Quincy QGV-100 Energy-Efficient Rotary Screw Air Compressor | 471 CFM | VSD Drive, 460V/3-phase. 471 cfm max capacity, 104-110 Degrees F maximum ambient temps. Water cooling. Touchscreen controller (ID UTY310037) displaying 5,262 hours, 76F internal temp, and 0 PSI outlet pressure at time of inspection. Control panel shows total panel rating 471A with largest motor FLA 163A, NEMA 4 enclosure. Equipped with BADGER PXE control package, enclosed sound-attenuated cabinet, and emergency stop with lockout provision.

Stock# 54253006

Used Quincy Air Treatment Unit - Mist Eliminator. Industrial compressed-air vessel, identified as Unit 3, is a vertical steel separator/filter housing designed for inline air-treatment service within a multi-compressor system. The unit features a bolted top cover with multiple service ports, heavy-duty welded legs, and integrated inlet/outlet connections sized for high-flow compressed-air applications. Internal rated 150 psi at -20 to 300 degrees F. Mounted on (3) legs. National Board & Serial# 890143. Built 2022.

Stock# 54253007

Used Quincy Mist Eliminator Air Treatment Unit. Industrial compressed-air vessel, identified as Unit 3, is a vertical steel separator/filter housing designed for inline air-treatment service within a multi-compressor system. The unit features a bolted top cover with multiple service ports, heavy-duty welded legs, and integrated inlet/outlet connections sized for high-flow compressed-air applications. Internal rated 150 psi at -20 to 300 degrees F. Mounted on (3) legs. National Board & Serial# 890142. Built 2022.

Stock# 54253008

Used Quincy Air Compressor Air Treatment Unit / Mist Eliminator. Industrial compressed-air vessel, identified as Unit 3, is a vertical steel separator/filter housing designed for inline air-treatment service within a multi-compressor system. The unit features a bolted top cover with multiple service ports, heavy-duty welded legs, and integrated inlet/outlet connections sized for high-flow compressed-air applications. Internal rated 150 psi at -20 to 300 degrees F. Mounted on (3) legs. National Board & Serial# 888920. Built 2022.

Stock# 54253009

Used Vertical Air Receiver Tank, carbon-steel ASME-certified pressure vessel manufactured by Samuel Pressure Vessel Group. Approximate 36" diameter x 108" straight side. Dished heads. The nameplate (NB 1050683) indicates MAWP 165 PSI at 400F and MDMT 20F at 165 PSI, with design data HD-176 and SH-187, built in 2023. The vessel features a cylindrical shell with welded elliptical heads, multiple threaded and flanged nozzles for inlet/outlet/process instrumentation, and a lower skirt base with side penetrations. It is externally coated in industrial blue enamel for outdoor service and integrated into a process piping system, likely functioning as a compressed-air or process-gas receiver, buffer tank, or filtration vessel.

Stock# 54253010

Used 500 Gallon Vertical Air Receiver Tank., ASME-coded pressure vessel fabricated by Samuel Pressure Vessel Group. Approximately 36" diameter x 108" straight side. Dished heads. Constructed of carbon steel with a high-build exterior blue coating for corrosion protection. The vessel is rated for MAWP 165 psi at 400F and MDMT -20F at 165 psi, with code stamp RT-4, and is supported on welded legs with integral bottom openings for drainage and piping connections. Multiple mid-shell and upper-shell nozzles allow integration into compressed air, gas drying, or buffer storage systems. The nameplate lists HD 294, SH 250, built 2020, Part No. C100898-X, CRN M135556012348Y.

Stock# 54253011

Used Air Receiver Tank, 500 Gallon, Vertical. Approximately 36" diameter x 108" straight side. Dished heads. ASME-code pressure vessel is manufactured by Samuel Pressure Vessel Group, with a U-stamp and 2023 fabrication year. The vessel is rated for 165 PSI at 400F, with an MDMT of 20F at 165 PSI. Nameplate data: HD 176 / SH 187, CRN M9775.5C, Part No. A10129. The unit features a welded cylindrical shell, threaded nozzles, and welded base supports with openings for piping. The exterior is coated blue for outdoor corrosion protection.

Stock# 54253012

Used Quincy QHD635 twin-tower heatless desiccant air dryer system, manufactured in 2022, complete with integrated control cubicle and pre-/post-filtration assemblies. The unit includes two vertical desiccant vessels with top-mounted pressure gauges and manifolded switching valves. The air dryer (serial APF267952) is rated for inlet pressures 411 bar, allowable inlet temperature 150C, and max outlet temperature 55C, and is built in Belgium by International Compressor Distribution N.V. The control cubicle (type 1900 5003 32 ED05, serial 3002383-33) operates on 24V control, supports 115-230V 2-phase supply, and is designed for 50/60 Hz operation with a 2 A rated current. The assembly is skid-mounted.

Stock# 54253013

Used Quincy Compressor system consists of a factory-built control cubicle (Type 1900 5003 32 ED05, S/N 3002383-27) operating on 24V control voltage with dual-frequency capability (50/60 Hz) and a 2-phase 115230V supply rated at 2 amps. The control panel manages a twin-receiver compressed air setup and includes integrated monitoring and protection circuitry with a kA-rated short-circuit tolerance. Paired with the compressor is a Quincy refrigerated air dryer, Model QHD635 (S/N APF267602, year 2022), designed for inlet pressures of 411 bar and temperatures from 150C, with a maximum outlet temperature of 55C.

Stock# 54253014

Used Quincy 3 compressed-air module consists of a dual-receiver tank assembly integrated with a factory-built Quincy control cubicle (Type 1900 5003 32 ED05, S/N 3002383-26), designed for 24V control voltage and dual-frequency operation at 50/60 Hz. The electrical system operates on a 2-phase 115230V supply with a 2-amp rated load, and incorporates protection and monitoring circuitry in a sealed control enclosure. The unit is paired with a Quincy refrigerated air dryer, Model QHD635 (S/N APF267527, 2022), rated for 411 bar inlet pressure, 150C allowable inlet temperature, and a maximum 55C outlet temperature.

Stock# 54279001

Used New York Blower High-Efficiency Airfoil Fan, Model AF-40. Size 544A71. Up to 240,000cfm, static pressures up to 46" WG. Operating temperatures up to 750 degrees F. Driven by a 400hp 3/60/460v 1780rpm WEG motor. Approximate Dimensions 9'8"W x 9'2"H x 8' Deep, inlet 50" dia., outlet 30"x50". Estimated under 10,000 lbs.

Stock# 54279002

Used NYB Fan. PLR wheel type. Class 4. Driven by a 200hp 3/60/460V, 17866 RPM, model C445T17DB18A Leeson motor. Built 2016.

Stock# 54381001

Used Temcon Automatic Re-winder and Perforator Machine, Model TRW 200. Industrial-grade converting system designed for high-efficiency roll slitting and rewinding applications. Min. 900 mm to Max. 1200 mm roll dimensions. (9) Knives, 3.75" cap Shaft dimension (Mother roll), Max. 195 m/min Capacity-speed, Product Dimension; Width 80-1600 mm, Perforation Length 100 -250 mm. Anti-bacterial conveyor bands. 316L CrNi product contact parts. Perforation length can be changed as per products specs, manual roll changing, pneumatic slitting, roll ejecting system. Machine is capable to fold the material V or C fold before perforation station. Built 2019. This unit is currently configured for dry wipe production.

Stock# 54382001

Used Fully Integrated Compressed Air System. System is centered around an Ingersoll Rand Rotary Screw Compressor, Model R55I-A125; ~29,637 runtime hours, 328 CFM Capacity, 115 PSIG Rated Operating Pressure, 125 PSIG Maximum Discharge Pressure, Nominal Drive 75hp, Nirvana VSD. System has centralized air storage, drying, filtration, and hard-piped distribution. System consists of: 1st Compressor, and 2nd Ingersoll Rand Rotary Screw Compressor (~15,276 runtime hours): (2) Air Receiver Tanks (400 and 1,200 gallon); (3) industrial line dryers (dual-tower configuration); Inline Compressed Air Filters (Multi-stage particulate and coalescing filtration); Main Compressed Air Distribution Header with Associated Piping. Designed for continuous industrial operations.

Stock# 54386001

Used Generac Diesel Generator, Model SD350. Rated 350kW, 438KVA. Weather Enclosure. Iveco/FPT engine power: 530 HP @1,800 RPM. 3/60/277/480V. Includes 2,000 gallon base tank. 275.4 hours, Serial# 7855510, Built 2013. Includes Square D Company 500 kVa transformer for 120V usage.

Stock# 54447001

Fully Refurbished Denver Sala Holo-Flite Dryer, Model D24-24-6. Indirect thermal sludge drying processor with dual holo-flite screws and vapor dome. Fully refurbished with new components. 316 Stainless Steel contact surfaces. (2) Screws 24'' diameter x 24' long, rated for 150 psi at 650 degrees F. Non-contact carbon steel exterior trough jacket rated 30 psi at 650 degrees F, Hot Oil or Water/Glycol heating medium. 10 HP Baldor motor. Contains Sumitomo Cyclo 6000 gearbox. Tomaso Built process control system provides fully automated operation of the Denver-Sala D24-24-6 dryer, ensuring consistent product quality, maximum throughput, and equipment protection across variable feed conditions; Product Temperature Protection, Residence Time Control, Feed Interlock System, Dynamic Safety Overrides, Vapor & Pressure Control, Mechanical Protection, Thermal Oil Control, Recipe-Based Operation, CIP Mode, HMI Interface. Fully refurbished 12/23/2025.

Stock# 54495001

Used Colorado Mill Equipment Pellet Mill, Model Mill-10. Rated capacity 80 to 600 lbs per hour, depending upon material. Equipped with an 8" flat die inner diameter and approximately 10 HP motor. Electrical requirements are listed as 3 phase, 208-230/460 volt. Serial #240106. This used CME Colorado Mill Equipment Mill-10 pellet mill is designed for pelletizing, material densification, and small to mid-range production applications involving compatible biomass, agricultural, feed, cannabis, hemp, or plant-based materials, depending on die configuration, moisture content, particle size, and process requirements.

Stock# 72054001

Used Adco Triseal Carton Former, Model AFHXX-40-3-WD. Three head former for tab-lock style hooded trays. All Stainless Steel construction Washdown Nema 4X. Top load carton / hooded tray size range: Length 3" to 17"; Width 3" to 8"; Depth 0.75" to 4" subject to tooling configuration. Now tooled for 3 trays: 6-7/8" x 6-1/4" x 2-1/4". Additional tooling is available, contact AEK for more information. Equipped with vacuum generator blank pick and place. Controls are Allen-Bradley CompactLogix L32E PLC, a AB PanelView 600 HMI. 230V.-3PH.-60Hz.-20 AMPS. Comp air 90 psi, cfm. Serial # 5871SL. Mfg. 02-26-09. See AEK # 72054002 for matching Adco Tri Seal Carton Closer.

Stock# 72452001

Used All Fill Semi-Automatic Auger Filler, Model B-300. Cycling speeds up to 120 per minute. Fill range from milligrams to 50 lbs. 15 Gallon 304 stainless steel agitated hopper, approximate 22" diameter x 21-1/2" deep. Tooling driven by a 1-1/2hp, 3/60/230/460 volt, 1140 rpm motor. Cerebus II computer controller. Has level detector. Serial # 22472.

Stock# 72680001

Unused- Yangzhou Yuxiang Vertical Volumetric Filler, Model GZJ. Fill weight adjustment 100 to 1000ml. Filling speed approximately 20 - 40 bottles per minute. Foot pedal operated. Stainless steel construction. Feed Hopper approximately 15" diameter x 9-3/4" straight side x 10-1/2" cone (Dented). 3/8" diameter nozzle threaded opening, air operated horizontal pusher 1-1/2" diameter x 1" push. 3-1/4" diameter x 6-7/8" push. Nozzle sizes: 3/16", 1/4", 3/8" diameters.

Stock# 72696001

Used Bradman-Lake Model SL 60 Automatic Intermittent Motion Horizontal End Load Cartoner. Capable of Speeds from 27 - 54 CPM, product dependent. Approximate size range 5.31" - 12" long x 1.97" - 10" wide x .75" - 3" tall x .75" - 1.57" minor flap. Has 12" centers with 9'6"L adjustable bucket infeed. Nordson 3400 hot melt glue system. Allen Bradley SLC 5/02 PLC Controls. 3/60/230 Volt. Currently setup for 7" long x 5" wide x 1-1/2" high carton.

Stock# 72698002

Used IMA Nova Model 7460(A300) Bulk Bottle Unscrambler With Integrated Bottle Cleaner. Capable of speeds up to 240 containers per minute. Bottle size range: 1" - 4" or 25mm - 100mm (diameter) x 2" - 7" or 50mm - 180mm (height). Allen Bradley Micrologix 1100 PLC. Includes bottle elevator, sorter and ionized air cleaner. 1/60/220 Volt, 20 amp.

Stock# 72698003

Used Bivans 54L Carton Former and Bottom Closer. Capable of speeds up to 60 cartons per minute. Has a carton size range: (Length) 1/2" - 8-7/8", (Width) 3/8" - 7", (Depth) 1-1/8" - 14-1/16". Set up for Hot melt glue bottom seal cartons. Includes Lexan safety guarding. Mounted on casters. 110V/1Ph/60Hz, 100 psi air. Currently set up for approximate 2-3/4"L x 2-3/4"W x 4-3/4"T carton.

Stock# 72698004

Used Zepf /Tampco Thiele Automatic Shrink Bundler, Model SA-27. Speeds up to 20 per minute. Maximum product height 12". Maximum film width 25". Has a right angle dual lane infeed. Has 27" W seal bar and with an integrated shrink tunnel. Cooling Fan on discharge. Integral controls. All stainless steel frame with Lexan guards. Portable mounted on casters. 3/60/480 Volt. Unit is in working condition with video of machine cycling. Set to size options for your product available upon receipt of samples.

Stock# 72942002

Used Acasi Model TruCap-6-Vert Automatic Inline Quill Capper. Capable of speeds over 100 CPM. Fully adjustable for cap sizes ranging from 8 mm to 130 mm in diameter. Dual belt side gripper, approximate 1" wide x 30" long. Adjustable height to accommodate containers from 1" to 14" inches tall. Has cleated belt cap elevator to pin style cap sorter. Currently set up on 38mm caps. 3/60/208 Volt.

Stock# 72951001

Used Multivac Stainless Steel Automatic Food Tray Sealer, Model T-300. Capable of speeds from 12 - 30 packs per minute (6 - 10 cycles/min). Tray former: 420mm x 300mm, divisible up to three uses. Tray height: up to 110mm. Has Busch Model R5-RA 0100 vacuum system. Top film web width (flexible): up to 500mm, max diameter of film roll 350mm. Dome application / Skin, has gas flush. Sew servo drive. Multivac / Beckhoff HMI. Includes Koolant Koolers chiller, model JHI-1000-M. Was originally set up to run trays of ground beef (not included). Mounted on casters. 3/60/220V.

Stock# 73095008

Used MG2 Futura Automatic Capsule Filler System. Capacity of 6,000 to 48,000 capsules per hour. Can run capsules sizes from 000 to 5, including tamper evident with proper change parts. MG2 control panel with Omron Sysmac PLC. Includes Futura MG2 Vacuum System. 3/60/480 Volt. Serial# 5267. 1 Set of change parts included, extra sets available for additional price.

Stock# 73395001

Unused- Plan It Packaging Systems Neptune RotoBagger Simplex 8ST-210 Pre-Made Pouch Form-Fill-Seal Machine. Rated 30-60 pouches/min; Up to 5kg (11 lbs.) fill weight (dependent on model); 100-300mm L x 100-210mm W pouch size range; Flat, back sealing, stand-up, special, and zipper pouch type capabilities; Heat seal; 10" PLC. Serial# 20318. Built 2022. With scale and 10 head weigher. OAD: 2780mm (approx. 110") L x 2180mm (approx. 86") W x 1420mm (approx. 56") H. 3/60/220V.Includes Incline Conveyor, Apollo 10H Multi Head Scale, Mezzanine Platform with Ladder, Rails and Stairs.

Stock# 73528001

Used Texwrap Horizontal Side Sealer with Shrink Tunnel, Model ST-1607SSR. Machine is rated for speeds up to 100 ft per minute (film). Includes Texwrap single chamber heat tunnel, model ST-1322. System has a package size range of: 4" - Infinite length; 2" - 20" width; up to 10" height. 24" long heat seal knife. 19" wide x 45" long infeed conveyor belt. 24" heat seal blade. Uses up to 32" wide center folded or flat film, powered scrap film unwind/remover. Pin perforation. Control panel with Allen Bradley MicroLogix 1400 PLC, (6) Control Techniques unidrive M200, Red Lion model G307K20U HMI. Mounted on casters. 15 amps. 1/60/115V. Serial# T1607SS-MTX52466. Built 2019.

Stock# 73621001

Used Wexxar Automatic Case Erector Sealer, Model WF-30T. Designed to run right handed cases. Machine is capable of speeds up to 30 cases per minute (depending on case size). Has a case size range of: 7.25" to 18" (length), 7.25" to 14" (width) and 6" to 15" (height). Bottom 2" Wide 3M Accuglide Taping Head. Pin and dome-style opening. Control panel with Allen Bradley CompactLogix L23E PLC, Omron NS8-TV00B-V2 Color touchscreen HMI, (2) Festo drives. 1/60/208 Volt, 10.7 Amp.

Stock# 73652001

Used Nordson EFD Automatic Dispensing System, Model G4V. 3 axis movement. Working area of 400 mm x 400 mm x 100 mm. 520/320 mm/s maximum speed. 3kg (6.6 lb) Tool payload. Driven by a 5-phase micro-stepping motor. Working temperature 10 - 40 degrees C (50 - 104 degrees F). Repeatability within 0.02 mm. Built 2022.

Stock# 73656001

Used Buhler Optical Sorter, Model SORTEX Z+3 RBL. Approx. 815 TPH (product dependent). 3-chute configuration. (24) Cameras total, 12 color and 12 IR. High-speed ejector system for accurate reject with low false loss. Touchscreen interface with programmable recipes. Hopper included. Built 2011. Previously used for pistachios.

Stock# 75822

Used C.E. Raymond 18" High-Speed, Air-Swept, Vertically Arranged Hammermill. Designed for ultra-fine grinding. Unit includes vertical shaft that carries all rotating internal components, rotor, (requires hammers and whizzer blades) fan blades, mill base, mill body with liners, screw feeder assembly, upper bearing housing, lower bearing housing, 25 hp drive motor.