Food and Beverage Equipment

Used Sharples P-660 Super-D-Canter Centrifuge | 6000 RPM | New Motors & PLC Panel | Stainless Steel | 1-Year Warranty

Used Sharples P-660 Super-D-Canter Centrifuge | 6000 RPM | New Motors & PLC Panel | 1-Year Warranty, stainless steel construction (product contact areas, max bowl speed 6000 rpm, single lead conveyor w/welded hardfacing wear protection, base, casing, feed pipe, 95:1 planetary gearbox, (New) 10 HP Main Drive motor, (New) 5 hp backdrive motor, mounted plate w/ vibration Isolations. Mounted on approx. 4 stainless steel stand w/casters, safety guards, (New) programable logic control/drive panel. (Reconditioned with warranty)

MFR: Sharples

Buy Used 6" PFA Jacketed Column – Heat Transfer & Corrosion Protection

Used- 6" PFA lined column, jacketed.

MFR: Unknown

Used Sharples P-660 Decanter Centrifuge | 6000 RPM | Stainless Steel | 7.5 HP Main Drive | Mounted w/ Vibration Isolation

Used Sharples P-660 Decanter Centrifuge | 6000 RPM | Stainless Steel | 7.5 HP Main Drive | Mounted w/ Vibration Isolation. Stainless Steel. Main drive motor 7.5 hp 3/60/230-460 volts, fixed speed. Backdrive motor2 hp 3/60/208 230-460 volts fixed speed. 6000 rpm max speed, 95:1 gearbox. Mounted on table with vibration isolators.

MFR: Sharples

Used Huaxing Three-Stage 150mm (6") Extrusion Line – Model HXSJ 150-DWM11

Used- Huaxing Three-Stage 150mm (6") Extrusion Line, Model HXSJ 150-DWM11. 30:1 L/D. Rated 600-1,000 kg (approx 1323-2205 lbs.) per hour. Consisting of: (1) 150mm x 4500mm (30:1) primary extruder, double vented w/ vacuum system and 2-stage filtration, and (1) 150mm x 1800mm (12:1) secondary extruder, single vented with 2-stage filtration, Driven by a 215hp 1785 rpm motor. One Crusher/compactor with infeed conveyor. Water bath strand cooling system with dewatering blowers, strand cutter, vibrating table, cooling tank, cooling tower, recirculation pumps, discharge vacuums, storage cyclone. pneumatic storage cyclone discharge. Main control panel. 60/480V. Built 2019. Previously used for PP and PE Plastics.

Used & Reconditioned Davis-Standard Thermatic 60IN60 6" Single Screw Extruder – 400 HP, 24:1 L/D, Thermatic Clamp

Used & Reconditioned Davis-Standard Thermatic 60IN60 6" Single Screw Extruder 400 HP, 24:1 L/D, Thermatic Clamp. 24:1 L/D ratio, water-cooled barrel, integrated water reservoir, recirculation pump, and heat exchanger. Equipped with a 17.21:1 gearbox rated for 424 HP capacity with a 1.5 service factor, powered by a new 400 HP TECO AC motor (Model EPS4004, 1,800 RPM, 449TX frame) and new TECO AC drive (Model EQ7-4450-C). Includes five barrel heating zones and six die heating zones with new Novus temperature controllers and amp gauges, swing-arm operator station with speed pod, pressure and screw speed gauges, and a 42" centerline height. Fitted with a Thermatic clamp and barrier flight screw; screw and barrel are within serviceable tolerances. Heater bands have been electrically tested, barrel plumbing and heat exchangers have been flow checked, and five new Red Hat solenoid valves have been installed. Approximate overall dimensions are 216" L x 80" W x 90" H. Originally built 2004.

MFR: Davis Standard

Used Davis-Standard 60IN60TPIH 6" Single Screw Extruder – 34:1 L/D, 400 HP, Vented Barrel with ABB Drive

Used Davis-Standard 60IN60TPIH 6" Single Screw Extruder 34:1 L/D, 400 HP, Vented Barrel with ABB Drive. Features a 34:1 L/D ratio with a water-cooled, vented barrel incorporating six cooling zones; vent is located approximately 130" from the center of the feed throat and is currently plugged. Cooling system includes a 1/2 HP recirculation pump, heat exchanger, and 32" x 24" x 12" water reservoir. Driven by a 400 HP WEG AC motor (1,790 RPM) with ABB AC drive and a Davis-Standard Model 60IN60TPIH gearbox featuring a 17.2:1 ratio and rated for 526 HP with a 1.5 service factor. Temperature controls include six-barrel zone Solo 4896 controllers and seven die zone Omron E5EC controllers. Operator controls feature a speed pod with screw RPM, motor load percentage, and pressure transducer gauges. Includes hopper, 42" centerline height, and serial number PT238. Approximate footprint is 25' L x 8' W. Built 1994.

MFR: Davis Standard

Used & Reconditioned Davis-Standard 600S Thermatic 6" Single Screw Extruder – 300 HP, 30:1 L/D, Reconditioned in 2025

Used & Reconditioned Davis-Standard 600S Thermatic 6" Single Screw Extruder 300 HP, 30:1 L/D, Reconditioned in 2025. Features a 30:1 L/D ratio with a PE/PP screw and a 17.21:1 gearbox ratio. Powered by a new 300 HP Westinghouse AC motor with a new WEG AC inverter drive. Equipped with a refurbished 10-zone control panel consisting of six barrel heating zones and four downstream zones, all fitted with new Eurotherm 3216 temperature controllers. Gearbox has been rebuilt with all internal bearings replaced except the thrust bearing. Serial No. F-9731, S.O. 901180. Electrical requirements are 460 Volt, 3 Phase, 60 Hz. Approximate overall dimensions are 242" L x 74" W x 102" H with an estimated weight of 23,000 lbs. Originally built in 1998, reconditioned in 2025.

MFR: Davis Standard

Used PTI 6000 6" Single Screw Extruder – 400 HP, 30:1 L/D, WEG Drive & Flender Gearbox

Used PTI 6000 6" Single Screw Extruder 400 HP, 30:1 L/D, WEG Drive & Flender Gearbox. Features a 30:1 L/D ratio with an air-cooled barrel, seven barrel heating zones, and sixteen downstream heating zones. Driven by a 400 HP WEG AC motor with WEG CFW-11 inverter drive and a Flender Model SZNF 390 gearbox featuring a 21.7:1 ratio and rated for up to 701 HP. Includes a 9" L x 7" W feed throat, 62" centerline height, 900-amp disconnect, and electrical requirements of 460 Volt, 3 Phase, 60 Hz (780 FLA). Mounted on V-groove casters for ease of positioning. Serial No. 3768. Approximate overall dimensions are 24' L x 100" W x 106" H with an estimated weight of 26,000 lbs. Built 2003.

MFR: PTI

Used Welex 6.0 30D 6" Single Screw Extruder – 500 HP, 30:1 L/D, Vented Barrel with Dynisco Hydraulic Screen Changer

Used Welex 6.0 30D 6" Single Screw Extruder 500 HP, 30:1 L/D, Vented Barrel with Dynisco Hydraulic Screen Changer. Featuring a 30:1 L/D ratio with an air-cooled, vented barrel (vent currently plugged) located approximately 120" from the center of the feed throat. Equipped with six barrel heating zones, nine die heating zones, Tempco Cool Touch heater bands, and a direct-driven Koellmann gearbox with an 8.7:1 ratio. Driven by a 500 HP Reliance AC motor rated for up to 200 screw RPM. Includes a 10" L x 8" W feed throat, 68" centerline height, and a 6" Dynisco hydraulic screen changer complete with hydraulic power unit. Electrical requirements are 460 Volt, 3 Phase, 60 Hz. Previously operated on PET resin. AC drive is not included. Approximate overall dimensions are 330" L x 84" W x 102" H with an estimated weight of 37,000 lbs.

MFR: Welex

Farrel Rubber/Plastic Laboratory Calender Mill – Inverted "L" 4-Roll, Adjustable Knives

Used- Farrel 4-Roll Inverted "L" Rubber/Plastic Laboratory Calendar Mill. 6" D x 13" L rolls. 500 degrees F max. roll temp. Up to 35 RPM. Fixed center roll w/ adjustable bottom, top, and offset. Full herringbone even speed gears on one side, Full herringbone friction gears on the other side. Nylon adjustable infeed guides. (2) adjustable twin knives on bottom roll. Cable safeties on both sides of frames. SCR drive w/ dynamic braking; Operators control station with variable speeds. Variable speed 7.5 HP motor. 3/460V. Serial# 73A1499.

MFR: Farrell

Used Sweco Vibro-Energy Separator 60" Diameter – Model XS60Y88HSTL, Single Deck

Used Sweco Vibro-Energy Separator 60" Diameter, Model XS60Y88HSTL. Stainless steel contact parts. Single deck, 2 separation. Driven by a 2.5hp, 3/60/460 volt, 1740rpm motor. No top cover. Mounted on painted carbon steel base. Serial# 167005-A06/18.

MFR: Sweco

Used Leistritz ZSE-60 GL Twin Screw Extruder – 36:1 L/D, 150 HP, Side Stuffer, Strand Dies, Screws & Spares

Used Leistritz ZSE-60 GL Twin Screw Extruder 36:1 L/D, 150 HP, Side Stuffer, Strand Dies, Screws & Spares. With (9) modular barrel sections. 114 kW / 150 HP Baumueller DC motor, 500 rpm max. screw speed, Barrels are electrically heated and internally cored for liquid cooling. Includes stand-alone Electrical enclosure/control panel (controls appear non-operational), LSB-47 twin screw side stuffer, Stand-alone pump tank/heat exchanger for barrels cooling, Two (2) Complete screw sets, segmented design with splined shafts, fully assembled, Approximately 25 pairs of spare screw elements, consisting of both flighted/conveying and mixing elements, Two (2) complete swing gate-type strand die assemblies, Three (3) or four (4) spare die plates. Numerous (approx.. 8-10) spare barrel closures & inserts Yr. 2000. Includes Allen Bradley DC Motor Drive. 480 50/60hz.

MFR: Leistritz Corporation