Contract Pharmaceutical Equipment

Used IKA Works Inline Dispax Reactor – Model MHD/DR-PB 20, 50 HP Homogenizer

Used- IKA Works Inline Dispax Reactor. Mixing/Homogenizing/Dispersing, Model MHD/DR-PB 20. Nominal flow rate 30 gallons per minute, solids capacity 6200 pounds an hour. Driven by a 50 hp, 3/60/460 volt, 3535 rpm motor. 4" Solid inlet, 3" liquid inlet, 2" outlet. Unit mounted on a base Part # P015897. Serial # 2603-12.

MFR: IKA Works

Used Rietz Disintegrator for Sale - 12” Diameter, 4” Outlet, Stainless Steel

Used- Rietz 12" Diameter 45 Degree Angle Disintegrator. 21" ID reduction chamber. (4) rows of 12" diameter, (5) hammers stacked on top with each other. (3) 12" diameter stainless steel 360 degrees reduction screens with 3/8" diameter perforations. Driven by Baldor 50hp, 3/60/460 volt, 3600 rpm direct drive motor. (2) 2" diameter sanitary threaded inlets with (1) reducer to 1" diameter tri-clamp, (1) 2" diameter tri-clamp fitting with cap. 4" Diameter sanitary thread outlet with reducer to 3" diameter tri-clamp fitting.

MFR: Rietz

Industrial PK Twin Shell V-Blender 50 Cu Ft – Stainless Steel Powder Mixer

Used Patterson-Kelley 50 cu. ft. Stainless Steel Twin Shell V-Blender. 65 lbs/cu. ft. Material density rating. 80 Degree shell. 316 Stainless steel construction. Approximately 18" charging ports, Approximately 10" discharge valve. Driven by approximately 10HP, 3/60/460 volt main drive xp motor. Intensifier bar, driven by 15hp, 3/60/460 volt xp motor. Control panel with Allen Bradley MicroLogix 1400 PLC and A/B PanelView Plus 1000 HMI. Mounted on a 304 stainless steel frame. 188-7/8" Approximate height it drum loader extended. Serial# C438080-2. Ideal for dry, free-flowing solids.

MFR: Patterson Kelley

Used Fryma VME-2400 2400 Liter Vacuum Mixer

Used 2400 Liter working capacity Fryma model VME-2400 vacuum mixer. The tank has an overall height of 101" to the top of lid including legs and 87" to the top with the lid removed. The overall diameter of tank with jacket is 63". The interior dimensions are: 61" diameter, 54" straight side height, 11" dome top, and 11" dish bottom. The working temperatures are 150 C for the interior and the jacket. The interior has a pressure rating of -1/+1 bar and the jacket has a 2.5 bar rating. There are two agitator drives, a 7.5 hp motor that drives a center 3 prop agitator and a scrape agitator through a chain drive and a 50 hp motor that drives a disperser type agitator off to the side of the center shaft. The top has an 8" flanged opening that is clamped shut and 6" glass inspection port with light. The top also has a 2" sanitary, 1.5" sanitary, and (2) 1" threaded fittings. The inside of the unit is polished to pharmaceutical grade. The bottom has a 6" sanitary discharge with a pneumatically operated valve. Fabrication # M10510. Requires 230/ 460 vac 3 phase electrical supply. Previously used for toothpaste. Good Condition.

MFR: Fryma

Used 50 / 10 hp Hockmeyer model HH-L50-10 dual shaft disperser. Stainless steel contact parts. It has one 64" dia. 3 bladed anchor style sweep agitator for the side and bottom (3.25" dia. x 44" long ...

Used-50 / 10 hp Hockmeyer model HH-L50-10 dual shaft disperser. Stainless steel contact parts. It has one 64" dia. 3 bladed anchor style sweep agitator for the side and bottom (3.25" dia. x 44" long shaft) and is driven by a 10 hp variable speed drive. It also has a 17" od high speed dispersion blade (2.9" dia. x 36" long shaft) that is driven by a 50 hp motor. Motors and controls are tagged for hazardous locations. Air over oil lift and includes the air/oil tank. 220 vac 3 ph electric power and air required. The overall dimensions of the disperser are 64" wide x 135" long x 86" tall. Please note: this mixer was designed for a relativly low ceiling height. It is designed so that 20" of the lift post sits through the floor or mezzanine. This unit comes with a 750 gallon open top carbon steel product mix tank that is 70" id x 45.5" tall straight side with a 6" center bottom drain.

MFR: Hockmeyer

Used The Fitzpatrick Company Fitzmill stainless steel GuiloRiver mill. Model 59. The GuiloRiver mill is used for pre-breaking or sizing frozen food products. The mill has 15" diameter x 20" wide roto...

Used-The Fitzpatrick Company Fitzmill stainless steel GuiloRiver mill. Model 59. The GuiloRiver mill is used for pre-breaking or sizing frozen food products. The mill has 15" diameter x 20" wide rotor, a 11.75" x 20.25" infeed hopper that is 74" from the ground, and a 17.5" x 21" discharge that is 36.5" from the ground. Rotor is driven by 50 hp 1770 rpm motor. Overall dimensions are 45" wide x 95" long x 92" tall. Serial number GR-20-538. Requires 208-220/440 vac 3 phase electrical supply.

MFR: Fitzpatrick

Used This Cowles disperser has an 86" long stainless steel shaft with a blade diameter of 20.5". Driven by a 100/50 hp, 1785/895 rpm motor that requires 440 vac, 3 ph electricity. Unit is equipped wi...

Used-This Cowles disperser has an 86" long stainless steel shaft with a blade diameter of 20.5". Driven by a 100/50 hp, 1785/895 rpm motor that requires 440 vac, 3 ph electricity. Unit is equipped with an air over oil lift. Shown on a stand for display purposes only. We also have (SPC-8794) the 1,500 gallon stainless steel tank that this disperser was paired with when it was installed. Designed for thru the floor mount/ mezzanine mount.

MFR: Cowles

Used This Cowles disperser has an 86" long stainless steel shaft with a blade diameter of 20.5". Driven by a 100/50 hp, 1785/895 rpm motor that requires 440 vac, 3 ph electricity. Unit is equipped wi...

Used-This Cowles disperser has an 86" long stainless steel shaft with a blade diameter of 20.5". Driven by a 100/50 hp, 1785/895 rpm motor that requires 440 vac, 3 ph electricity. Unit is equipped with an air over oil lift. Shown on a stand for display purposes only. We also have (SPC-8795) the 1,500 gallon stainless steel tank that this disperser was paired with when it was installed. Designed for thru the floor mount/ mezzanine mount.

MFR: Cowles

Used Herman Hockmeyer and Co. disperser has a stainless steel shaft length of 45" and a blade diameter of 18". Unit is equipped with an air over oil lift. Variable speed. Driven by a 50 hp, 1800 rpm ...

Used-Herman Hockmeyer and Co. disperser has a stainless steel shaft length of 45" and a blade diameter of 18". Unit is equipped with an air over oil lift. Variable speed. Driven by a 50 hp, 1800 rpm motor that requires 220/440 vac, 3 ph electricity. Overall dimensions are approximately 52" w x 94" l x 100" h. Motor is tagged for hazardous location.

MFR: Hockmeyer

Used This Cowles disperser has two (2) stainless steel shafts that measure 54" long with a blade diameter of 12.5". Each shaft is driven by a 50 hp, 1770 rpm motor that requires 230/460 vac, 3 ph ele...

Used-This Cowles disperser has two (2) stainless steel shafts that measure 54" long with a blade diameter of 12.5". Each shaft is driven by a 50 hp, 1770 rpm motor that requires 230/460 vac, 3 ph electricity. Rated for hazardous locations. Unit is equipped with an air over oil lift.

MFR: Cowles

Used 50 cu ft stainless steel ribbon blender with triple helix blade. The trough is 82" wide with a 36.25" diameter and 19.5" straight side height. The blade diameter is 35" the blade width is 2". 8"...

Used-50 cu ft stainless steel ribbon blender with triple helix blade. The trough is 82" wide with a 36.25" diameter and 19.5" straight side height. The blade diameter is 35" the blade width is 2". 8" diameter center bottom discharge with flush valve. The dimensions of the blender are 44" wide by 122" long by 62" high. The stand is 97" long by 72" wide by 82" tall. The 7.5 hp motor requires 208 vac and is 44" long by 25" wide by 19" tall. There is a chain cover that is 74" long by 6.5" wide by 27" tall.

Used Prater Industries model CLM-35 two-stage air classified hammer mill for fine grinding of difficult to grind particles. Carbon steel construction. It has a 50 hp 3550 rpm main drive and a 7.5 hp...

Used-Prater Industries model CLM-35 two-stage air classified hammer mill for fine grinding of difficult to grind particles. Carbon steel construction. It has a 50 hp 3550 rpm main drive and a 7.5 hp motor for the internal classifier. The inlet is 3.25" x 4.5" and is fitted with a magnet. Discharge grind range of 149 microns to a mean size of 5 to 7 microns. Mounted on a carbon steel base. 460 vac 3 ph electrical power required for the main drive 230/460 vac 3 ph required for the classifier drive. Serial number 391002.

MFR: Prater