Contract Pharmaceutical Equipment

Used VAV Scan vibratory Conveyor. Stainless steel construction. Conveyor pipe of 16" diameter and 148" long. Has clean out openings on boths ends. The unit has three 6" inlets/outles and two 12" inl...

Used VAV Scan vibratory Conveyor. Stainless steel construction. Conveyor pipe of 16" diameter and 148" long. Has clean out openings on boths ends. The unit has three 6" inlets/outles and two 12" inlets/outlets. Equipped with 2 vibro motors, 1200 rpm each. Has a support floor mounting with 4 springs and 4 schocks absorbant. 41" in the tall end and 8 1/2" in the short end. The unit number : 29759 and year: 1991.

Used This is a Szegvari Union Process model 1SD, Type B attritor mill system. Its serial number is 990702. Stainless steel contact parts. It is equipped with a 5 hp explosion proof varidrive, tach...

Used-This is a Szegvari Union Process model 1SD, Type B attritor mill system. Its serial number is 990702. Stainless steel contact parts. It is equipped with a 5 hp explosion proof varidrive, tachometer and jacketed bowl. The bowl has a total capacity of 1.5 gallons with a workin capacity of 0.8 gallons. 230/460 vac 3 ph power required. This unit comes with a 38 gallon jaketed mix tank with dispersion and side scraping agitation and also a diaphragm pump. This is a nice system that can be used for wet or dry milling. Good condition.

MFR: Union Process

Used Fluid Air PolarDry 050 Electrostatic Spray Dryer – 50 kg/hr

Used- Fluid Air PolarDry Model 050 Electrostatic Spray Dryer 50 Kg/Hr Evaporation Capacity. Designed for GMP processing with nitrogen drying and atomizing gas. Rated for maximum evaporation capacity of 50 kg/hr, maximum drying gas inlet temperature of 140 C, maximum drying gas flow of 1,870 m/hr, and design vacuum of 12 kPa. Atomizing gas specifications include maximum inlet temperature of 150 C, maximum pressure of 4.14 bar, and design flow of 100 m/hr. Features stainless steel spray chamber with FDA-approved PTFE liner, electrostatic atomization technology, pneumatic powder collection and conveying system, (3) reverse-pulse cartridge filters, HEPA filtration, dehumidification coil, drying gas heater, blower, and oxygen monitoring safety system. Equipped with Watson Marlow peristaltic feed pump, Allen-Bradley PLC with Batch Architect control system, operator HMI, stainless steel process skid, and elevated access platform with stairs. Product contact surfaces include 316L stainless steel and FDA-approved PTFE. Electrical requirements include 480V, 3-phase, 60 Hz. Possible applications include pharmaceutical, nutraceutical, biotechnology, food ingredient, and specialty chemical spray drying of compatible liquid formulations into powdered products.

MFR: Fluid Air

Used Fluid Air PolarDry Model 001 Laboratory Electrostatic Spray Dryer, 1 kg/hr

Used- Fluid Air PolarDry Model 001 Electrostatic Spray Dryer, 1 Kg/Hr Evaporation Capacity. Designed for cGMP laboratory, research and development, and pilot-scale processing of aqueous feedstocks. Rated for maximum evaporation capacity of 1 kg/hr with (1) electrostatic atomizing nozzle, maximum nitrogen drying gas inlet temperature of 140 C, drying gas flow of 43 Nm/hr, maximum atomizing gas temperature of 150 C, and maximum atomizing gas pressure of 552 kPa. Features 316L stainless steel and ULTEM machine tower construction, FDA-approved acrylic spray chamber, (2) 5-micron polyester cartridge filters with 316 stainless steel wire mesh and reverse-pulse cleaning, HEPA exhaust filtration, electric drying gas heater, brushless DC blower, and 1-liter glass powder collection system. Equipped with Watson Marlow 313 peristaltic feed pump with 6220 RPM operating range, AccuJet electrostatic nozzle controller, Allen-Bradley PLC with Batch Architect controls, operator touchscreen HMI, nitrogen inerting system, and integrated safety monitoring. Electrical requirements: 208240V, single phase, 50/60 Hz, 30 amps. Compact, portable stainless steel design. Possible applications include laboratory spray drying, powder formulation development, microencapsulation, pharmaceutical research, nutraceutical development, and processing of compatible aqueous food and specialty ingredient formulations.

MFR: Fluid Air

Used Dr. Pharm LHSG300 300 Liter High Shear Mixer Granulator With AHU

Used Dr. Pharm LHSG300 High Platform High Shear Mixer And Wet Granulator With TAHM07S-CII Air Handling Unit. Serial # 0116, Built December 2017. Features 300-liter bowl with 240-liter working volume, 50120 kg batch capacity and 304 stainless steel product-contact surfaces. Bottom-driven mixing paddle operates at 2177 rpm with 22 kW motor, granulating chopper at 503,000 rpm with 5.5 kW motor, and co-mill at 501,500 rpm with 5.5 kW motor. Equipped with pneumatic discharge, seal-air system, in-place cleaning, Siemens touchscreen/PLC controls, variable-frequency drives, automatic/manual operation, recipe controls, safety interlocks, access platform, stairs and guardrails. Rated 220V, 60 Hz and 40 kW total power. Includes Hanlin Hangyu Model TAHM07S-CII Air Handling Unit, Serial # FG1232080-A, Built October 2017, rated 7,000 cubic meters per hour air/fresh-air volume, 66 kW electric heat, 220V, 3-phase, 60 Hz, with HEPA filtration; AHU dimensions approximately 89.8" x 45.7" x 49.2" and weight 1,168 lb. Suitable applications include pharmaceutical, food, chemical and light-industry powder mixing, dry powder mixing and wet granulation.

Used Dr. Pharm NTFZ-120 Lifting Tilting and Granule Sizing Machine

Used Dr. Pharm NTFZ-120 Lifting And Tilting Sizing Machine. Serial # 067, Built December 2017. Designed for lifting, tilting, conveying and sizing granulated material in a closed process. Features stainless steel construction, hydraulic lifting system, integrated granule sizing mill, push-button controls and tilt control stick. Machine nameplate specifies 3,800 mm total height, 1,550 mm maximum lift height, 16 MPa hydraulic pressure, 220V electrical service and 7.5 kW total power. Manufacturer information lists the NTFZ series for connection with fluid bed granulator and fluid bed dryer product containers, allowing material transfer and sizing before the next process step. Possible applications and suitable products include pharmaceutical, food, chemical and dairy processing for lifting, transferring and sizing dry granules and other solid materials.

Used Dr. Pharm LD-300 300 Liter Stainless Steel Blending Bin

Used Dr. Pharm LD-300 Stainless Steel Blending Bin. Featuring enclosed product container, removable top cover with gasket, conical bottom discharge with manual butterfly valve, heavy-duty tubular stainless steel frame and casters for mobility. The LD-300 designation corresponds to a 300-liter class blending bin used with solid-dose processing equipment. Possible applications and suitable products include contained handling, blending, storage and transfer of pharmaceutical powders, granules and other dry solid products.

Dr. Pharm LD-300 Stainless Steel IBC Blending and Transfer Bin

Used Dr. Pharm Stainless Steel Blending Bin, Model LD-300. Featuring enclosed product container, removable top cover with gasket, conical bottom discharge with manual butterfly valve, heavy-duty tubular stainless steel frame and casters for mobility. The LD-300 designation corresponds to a 300-liter class blending bin used with solid-dose processing equipment. Possible applications and suitable products include contained handling, blending, storage and transfer of pharmaceutical powders, granules and other dry solid products.

Used Patterson-Kelley Stainless Steel Cross-Flow V-Blender

Used Patterson-Kelley Cross-Flow V-Blender, Serial # C441269-2. Features Patterson-Kelley's unequal V-shell design, which creates axial material movement during rotation for efficient, uniform tumble blending while providing gentle handling in an enclosed system. Patterson-Kelley lists Cross-Flow designs for powders, granules and dry bulk solids, with stainless steel sanitary construction and configurations ranging from laboratory through production scale. Possible applications and suitable products include blending pharmaceutical powders, nutraceutical ingredients, food ingredients, chemicals, fine powders, granules and other free-flowing dry solids.

MFR: Patterson Kelley

Unused CMS Heat Transfer Division, Inc. shell-and-tube heat exchanger, manufactured in Bohemia, New York, for Cincinnati Heat Exchangers. Unit is rated for 160 PSIG MAWP at 400F on both shell and tub...

Unused CMS Heat Transfer Division, Inc. shell-and-tube heat exchanger, manufactured in Bohemia, New York, for Cincinnati Heat Exchangers. Unit is rated for 160 PSIG MAWP at 400F on both shell and tube sides, with an external pressure rating of 14.7 PSIG at 400F. Manufactured in 2022 to ASME Section VIII requirements.

Used Pieralisi SPI 3 Decanter Centrifuge – 40 HP Stainless Steel Contact Parts

Used- Pieralisi SPI 3 Decanter Centrifuge. Stainless steel contact parts. 3350 maximum RPM. 1.4 kg/dm^3/approximate 87.4lbs/cubic foot maximum product density. 30 kW/Approximate 40 HP motor. 3/60/480V. Serial# J03338. Built 2002. Previously used for olive oil. Machine dimensions 154" L x 65" H x 51" W

MFR: Pieralisi

Used Kato 1 MW Natural Gas Generator with Waukesha L7042GSI Engine

Used- Kato Natural Gas Generator Package, Rated 1MW. Powered by a Waukesha Model L7042GSI engine. Components include: Exco Industrial Switchgear; ABB SACE L2895 1600 amp breaker/switch; McPherson ADVR-083 regulator; Woodward 2301A Control system; Altronic CPU-95 Ignition System; Altronic CPU-95 Enhanced Display Module; NewMar Battery Charger; and cooling system. 3ph, 480V, 1200 RPM. Rebuilt by Reagan Power and Compression in 2025. Reported 500 hours since rebuild.