Contract Packaging Equipment
Stock No.:
54687141Used MAC model 47-RFHC stainless steel reverse pulse jet dust collector has two (2) 30" long dust collector cartridges with 295 sq. ft. of filter media each. With a 47" diameter, 96" straight side, a...
Used-MAC model 47-RFHC stainless steel reverse pulse jet dust collector has two (2) 30" long dust collector cartridges with 295 sq. ft. of filter media each. With a 47" diameter, 96" straight side, and 70" cone length, this dust collector totals to be about 57" w x 64" l x 174" h. There is a flanged clean air outlet that measures 3.25". Discharge port is 10". Serial no. 28415-012-1.
MFR: MAC
Stock No.:
54687142Used MAC model 47-RFHC stainless steel round reverse pulse jet dust collector holds (2) 30" long dust collecting cartridges with 295 sq. ft. of filter media. There are 3 load cell sensors. With a 47"...
Used-MAC model 47-RFHC stainless steel round reverse pulse jet dust collector holds (2) 30" long dust collecting cartridges with 295 sq. ft. of filter media. There are 3 load cell sensors. With a 47" diameter, 124" straight side, and 70" cone length, this dust collector totals to be about 57" w x 64" l x 232" h. There is a flanged clean air outlet that measures 2". Attached to the discharge port is a MAC multi-duty rotary valve blow-thru. Serial no. 28415-001-1
MFR: MAC
Stock No.:
409352Pre-Owned Vulcan K6ETT Electric Counter Kettle | 6 Gal | 50 PSI
Used Vulcan-Hart Model K6ETT Electric Counter Tilting Kettle, 6 Gallon Capacity. Approximately 11.8" Diameter x 14-1/2" deep. Ellipsoidal bottom. 2/3 Jacketed rated 50psi at -20 to 300 degrees F. Frame mounted. National board# 21596, Serial# 46-3002235, Built 2011. 3/1PH 50/60HZ 8/10KW 208/240V requirements.
MFR: Vulcan
Stock No.:
47890001Lodige FKM600D Plow Mixer
Used- Lodige Model FKM600D batch-type plow mixer with 6 cubic feet working capacity and 10 cubic feet total capacity. 304 stainless steel, non-jacketed mixing chamber approximately 32" diameter x 50" long with 4" diameter shaft, (3) bolt-on plows, (2) bolt-on end scrapers, (2) 18" x 15-1/2" side access doors, and (2) 12" top openings. 9" x 7" bottom outlet with manually operated door and air-purge seals. Serial # 9046. Driven by an approximately 10 hp motor through Falk reducer. Includes control panel with Allen-Bradley PanelView 600 and SLC 5/04 CPU. Mounted on carbon steel stand. Suitable for dry powders, premixes, granular ingredients, spices, nutraceuticals, feed additives, chemical blends, and similar products.
MFR: Lodige
Stock No.:
50556009Used - Paint Media Mill, 8" x 30" Milling Chamber, 6 Gallon, 10 HP Motor
Used- Paint Media Mill. includes 8" diameter X 30" high milling chamber, approximate 6 gallon. Stainless Steel screening section, jacketed chamber. Driven by 10 HP, 220/440 V, 1740 RPM, 3-phase, 60 cycle motor. Previously used at paint processing facility and in working condition when removed from service. No Manufacturers Tag.
MFR: Unknown
Stock No.:
51065016Used Stewart Bolling 6" x 12" Pilot Two Roll Rubber Mixing Mill
Used Stewart Bolling 6" x 12" Pilot Scale Two Roll Mixing Mill With 5 HP Gear Motor. Designed for laboratory, pilot plant and small-batch processing of compatible rubber, plastic and polymer compounds. Features (2) chrome-cored rolls measuring approximately 6" diameter x 12" long, driven by a 5 HP single-speed gear motor with a fixed gear ratio. Equipped with two-point manual roll gap adjustment for controlling material thickness and split end guides for containing material within the working roll area. Safety features include front and rear knee-operated safety mechanisms and an over-the-roll safety cage. Electrical requirements are 220/440 volts, 3-phase, 60 Hz. Serial #2560. Possible applications include rubber compounding, polymer blending, plastic material processing, sheeting, mastication and mixing of compatible natural rubber, synthetic rubber, elastomers, thermoplastic compounds, pigments, fillers and other suitable rubber or polymer formulations.
MFR: Stewart Bolling
Stock No.:
54180001Farrel Rubber/Plastic Laboratory Calender Mill – Inverted "L" 4-Roll, Adjustable Knives
Used- Farrel 4-Roll Inverted "L" Rubber/Plastic Laboratory Calendar Mill. 6" D x 13" L rolls. 500 degrees F max. roll temp. Up to 35 RPM. Fixed center roll w/ adjustable bottom, top, and offset. Full herringbone even speed gears on one side, Full herringbone friction gears on the other side. Nylon adjustable infeed guides. (2) adjustable twin knives on bottom roll. Cable safeties on both sides of frames. SCR drive w/ dynamic braking; Operators control station with variable speeds. Variable speed 7.5 HP motor. 3/460V. Serial# 73A1499.
MFR: Farrell
Stock No.:
51188012Used Siemens EK1000-2 6.56 MW Steam Turbine Generator Plant
Used- Siemens 6.56 MW Steam Turbine Generator Plant, Model EK1000-2, Manufactured 1981. Siemens Model EK1000-2 multistage extraction/condensing steam turbine generator system, rated at 6,560 kW (6.56 MW) shaft output, manufactured in Germany in 1981, Serial No. T5719. Turbine designed for operation at 9,000 RPM with live steam pressure of 48.3 bar (700 PSI) at 404C (759F), intermediate steam extraction pressure of 7.3 bar (106 PSI), and condensing exhaust design pressure of 12 kPa absolute. Equipped with Siemens 6:1 speed reduction gearbox, rated at 6,900 kW continuous duty, reducing turbine speed from 9,000 RPM to 1,500 RPM. Driven generator is a Siemens Model 1DU7534-7FE82-Z three-phase synchronous alternator, Serial No. D8025106101, rated at 8,200 kVA, 11,000 volts, 50 Hz, 1,500 RPM, with 0.8 power factor. System includes associated excitation equipment, electrical control and protection panels, Siemens and GE protection components, SEL digital relays, DECS-250 digital excitation controller, lubrication system with approximately 6,300-liter oil reservoir, and (2) Alfa Laval Model M10-BDFG plate heat exchangers manufactured in 2021. Associated plant equipment includes main steam condenser and steam dump condenser, subject to confirmation of sale scope. Turbine and gearbox underwent extensive major inspection and maintenance in JulyAugust 2023, including rotor removal, internal inspections, non-destructive testing, rotor dynamic balancing, gearbox inspection, bearing inspection, generator electrical testing, and vibration assessment. Inspection records reported acceptable gearbox condition and low post-commissioning vibration levels at that time. Main condenser was retubed in 2012 and inspected in 2023. Originally installed as part of an industrial cogeneration and energy recovery system at a sulphuric acid production facility. Complete engineering documentation, maintenance records, mechanical drawings, electrical schematics, and inspection reports available.
Stock No.:
47147033Used Lee 60 Gallon Stainless Steel Steam Jacketed Kettle Model 60D7S
Used Lee 60 Gallon Stainless Steel Cooking & Mixing Kettle, Model # 60D7S, Serial # 32675-1, built in 2004. Stainless steel 60 gallon kettle equipped with a single-action scraped-surface agitator with scrapers missing. Steam jacket is rated for 90 psi at temperatures up to 332 F, National Board number 9758. Kettle has a 1.5" diameter outlet with pneumatic discharge valve and is driven by a 1 HP, 3 phase, 60 cycle, 230/460 volt motor. Suitable for cooking, heating and mixing applications involving products that can be processed in a steam-jacketed, agitated kettle.
MFR: Lee Ind
Stock No.:
47147036Used Groen RA-60 60 Gallon Stainless Steel Jacketed Cooking Kettle with Agitator
Used Groen 60 gallon stainless steel jacketed cooking and mixing kettle, Model # RA-60, Serial # 03588, National Board number 139462, equipped with a single-action scraped-surface agitator with scrapers missing, 125 psi steam jacket rated up to 353 F, 1.5" diameter outlet, and 1.5 HP, 3-phase, 60-cycle, 230/460-volt motor with final agitation speed of 34 RPM. Suitable for batch cooking, heating, blending, and mixing applications and products requiring low-speed scraped-surface agitation.
MFR: Groen
Stock No.:
53566001Used Hydro-Pac LX Carbon Dioxide Compressor, Model C02.2-60-1975LX-CO2. Single stage; 400 to 2176 psi suction pressure; 2176 psi max. discharge pressure; Capacity @ 600 psig, 55 degree F inlet: 127 scfm; Capacity @ 870 psig, 55 degree F inlet: 989 scfm; 15 gpm (minimum) cooling water requirements at 60-80 degrees F. 60 HP, 3/60/230/460V motor, 120V control. Built 2020.
Used- Hydro-Pac LX Carbon Dioxide Compressor, Model C02.2-60-1975LX-CO2. Single stage; 400 to 2176 psi suction pressure; 2176 psi max. discharge pressure; Capacity @ 600 psig, 55 degree F inlet: 127 scfm; Capacity @ 870 psig, 55 degree F inlet: 989 scfm; 15 gpm (minimum) cooling water requirements at 60-80 degrees F. 60 HP, 3/60/230/460V motor, 120V control. Built 2020.
