Chemical Equipment

Used Niro Mobile Minor Type HT Stainless Steel Spray Dryer with Rotary Atomizer

Used Niro Mobile Minor Type HT Stainless Steel Portable Spray Dryer With Air-Driven Rotary Atomizer, Electric Heating And 17 Kg/Hour Evaporation Capacity. Industrial laboratory and pilot-scale spray drying system designed for converting compatible liquid solutions, suspensions, emulsions and slurries into dry powders through atomization and controlled hot-air drying. Features a stainless steel drying chamber measuring approximately 32" in diameter x 24" straight side, equipped with an electrically heated air system capable of temperatures up to approximately 350 C (662 F). Rated for approximate water evaporation capacities ranging from 2.2 to 15.4 lbs per hour (1 to 7 kg/hour), depending on feed composition, moisture content, inlet and outlet air temperatures and operating conditions. Equipped with a top-entering, air-driven Niro rotary atomizer designed to disperse liquid feed into fine droplets within the drying chamber, promoting rapid moisture evaporation and powder formation. Includes a cyclone separator for recovering entrained dried particles from the exhaust air stream, an operator control panel for process operation and a center bottom discharge outlet. Portable configuration mounted on wheels for movement between laboratory, pilot plant and small-scale production areas. Manufactured by Niro. Serial #1952. Possible applications include spray drying, powder production, moisture removal, particle formation, formulation development and pilot-scale processing of compatible dairy ingredients, coffee extracts, food flavorings, proteins, nutraceutical ingredients, pharmaceutical formulations, specialty chemicals, ceramic suspensions, pigments and other suitable liquid or slurry-based materials.

MFR: Niro

Used Vivtek PSD-P5 Pilot Spray Dryer – Food-Grade Powder Production System with Dust Collection (2023)

Used- Vivtek Instruments Pilot Spray Dryer, Model PSD-P5. 5-8 kg/hour (approx. 11-17.5 lbs./hour) evaporation capacity. 32" diameter x 60" long drying chamber. 6" diameter x 16" long cyclone. Two-fluid atomizer: 1, 1.5, and 2 mm. 280 degrees C. (538 degrees F.) max. temperature. 12 kW heater. 750W air blower. 3ph/230V. With dust collector. Built 2023. Previously used for food/beverage emulsion powder.

Used 3,200 Gallon Stainless Steel Tank – Vertical Dished Vessel with Multiple Po

Used- Stainless Steel Vertical Storage Tank, Approximately 3,200 Gallon Capacity. Approximately 88" diameter x 120" straight side. Tank features dished top and bottom heads, (2) 4" top openings, (4) 2" top openings, a 2" lower side outlet, a 3" bottom outlet, and a 4" center bottom outlet with approximately 32" discharge height. Equipped with a lower side manway with cover and supported by (4) stainless steel legs. Manufacturer identification tag not present. Possible applications include liquid storage, intermediate bulk storage, and batch holding of water, liquid ingredients, chemicals, and other compatible non-pressurized liquid products.

Unused CECO Peerless 324 Gallon 316 Stainless Steel Vertical Oxygen Separator Vessel | ASME Pressure Vessel

Unused CECO Peerless 324 Gallon 316 Stainless Steel Vertical Oxygen Separator Vessel | ASME Pressure Vessel. 42" ID Vertical Oxygen Separator, PMC Part No. VGSP-42I-380SS-001, Drawing No. 9558B-1, is a heavy-wall vertical ASME pressure vessel designed for high-pressure oxygen service and deflagration control applications. Fabricated entirely from 316 stainless steel in accordance with ASME Section VIII Division 1, 2023 Edition, the vessel is rated for full vacuum to 380 PSIG at 194F with a MAWP of 380 PSI at 194F, a MAP of 380 PSI at 100F, and an MDMT of -4F at 380 PSI. The separator is fully ASME U-stamped and National Board registered, requires RT1 radiography, and is hydrostatically tested to 494 PSI for one hour with no PWHT required. Construction includes a 1/2" thick SA-240-316 shell, 1/2" thick 2:1 ellipsoidal heads with 0.4024" minimum formed thickness, heavy-wall Schedule 160 drain and liquid outlet nozzles, reinforced manway assembly, four support legs, lifting lugs, and a davit arm assembly. The vessel includes multiple flanged process and instrumentation connections consisting of 2" inlet, liquid inlet, and outlet nozzles, 3" liquid outlet and drain nozzles, a 2" gas purging connection, 1" DPIT, pressure indicator, vent, and relief valve nozzles, dual 3/4" level gauge connections, dual 1" level controller connections, four 1" level switch connections, and an 18" Class 300 manway. Internal surfaces are oxygen cleaned with neoprene gaskets and flange covers installed for shipment, while the exterior is cleaned, de-scaled, and finished with a sugar blast coating. Estimated vessel weights are approximately 2,412 lbs empty, 5,154 lbs operating, and 5,163 lbs hydrotest weight, with an internal capacity of approximately 324 gallons and a center of gravity located 13.12" from datum. The engineering design package includes ASME VIII Division 1 stress calculations, nozzle reinforcement analysis, hydrostatic test verification, wind and seismic analysis, structural support calculations

MFR: Peerless

Unused CECO Peerless 316 Stainless Steel Oxygen Separator Pressure Vessel | 380 PSI ASME Vessel

Unused CECO Peerless 316 Stainless Steel Oxygen Separator Pressure Vessel | 380 PSI ASME Vessel. 42" ID Vertical Oxygen Separator, PMC Part No. VGSP-42I-380SS-001, Drawing No. 9558B-1, is a heavy-wall vertical ASME pressure vessel designed for high-pressure oxygen service and deflagration control applications. Fabricated entirely from 316 stainless steel in accordance with ASME Section VIII Division 1, 2023 Edition, the vessel is rated for full vacuum to 380 PSIG at 194F with a MAWP of 380 PSI at 194F, a MAP of 380 PSI at 100F, and an MDMT of -4F at 380 PSI. The separator is fully ASME U-stamped and National Board registered, requires RT1 radiography, and is hydrostatically tested to 494 PSI for one hour with no PWHT required. Construction includes a 1/2" thick SA-240-316 shell, 1/2" thick 2:1 ellipsoidal heads with 0.4024" minimum formed thickness, heavy-wall Schedule 160 drain and liquid outlet nozzles, reinforced manway assembly, four support legs, lifting lugs, and a davit arm assembly. The vessel includes multiple flanged process and instrumentation connections consisting of 2" inlet, liquid inlet, and outlet nozzles, 3" liquid outlet and drain nozzles, a 2" gas purging connection, 1" DPIT, pressure indicator, vent, and relief valve nozzles, dual 3/4" level gauge connections, dual 1" level controller connections, four 1" level switch connections, and an 18" Class 300 manway. Internal surfaces are oxygen cleaned with neoprene gaskets and flange covers installed for shipment, while the exterior is cleaned, de-scaled, and finished with a sugar blast coating. Estimated vessel weights are approximately 2,412 lbs empty, 5,154 lbs operating, and 5,163 lbs hydrotest weight, with an internal capacity of approximately 324 gallons and a center of gravity located 13.12" from datum. The engineering design package includes ASME VIII Division 1 stress calculations, nozzle reinforcement analysis, hydrostatic test verification, wind and seismic analysis, structural support calculations

MFR: Peerless

Used 333 Sq Ft Heat Exchanger, Duplex 2205 Construction, 662 PSI Shell Rating, 2023

Used Wuxi Chemical Equipment Horizontal 333 sq. ft. Shell and Tube Heat Exchanger. 3/4" dia Duplex 2205 stainless steel tubes rated 288.3 psi at 32 to 330 degrees F, 16' 7'' tube length. Duplex 2205 shell rated 662.3 psi at 32 to 300 degrees F. 15'' Shell diameter. Carbon steel head. National Board #573, Serial #WHA22-087-2-2-C, built 2023.

Unused Wuxi Chemical Equipment 333 Sq Ft Shell & Tube Heat Exchanger, Duplex 2205, 2023

Unused Wuxi Chemical Equipment 333 Square Foot Horizontal Shell and Tube Heat Exchanger. Duplex 2205 stainless steel tubes rated 288.3 psi at 32 to 330 degrees F, 16' 7'' Tube length. Carbon steel head. 15'' Shell diameter. Duplex 2205 shell rated 662.3 psi at 32 to 300 degrees F. National Board #572, Serial #WHA22-087-2-1-B, built 2023.

Unused Wuxi 333 Sq Ft Shell and Tube Heat Exchanger, Duplex 2205 Tubes & Shell, High Pressure

Unused Wuxi Chemical Equipment 333 Square Foot Shell and Tube Heat Exchanger, Horizontal. Duplex 2205 stainless steel tubes rated 288.3 psi at 32 to 330 degrees F, 16' 7'' Tube length. 15'' Shell diameter. Carbon steel head. Duplex 2205 shell rated 662.3 psi at 32 to 300 degrees F. National Board #574, Serial #WHA22-087-2-2-D, built 2023.

Unused Hayes & Stolz HR72x144SSCI 339 Cu. Ft. Stainless Steel Jacketed Ribbon Blender – 60 HP, 3,500 Lbs/Hr, Temperature-Controlled Mixing

Unused Hayes & Stolz HR72x144SSCI 339 Cu. Ft. Stainless Steel Jacketed Ribbon Blender 60 HP, 3,500 Lbs/Hr, Temperature-Controlled Mixing. Constructed of 304 stainless steel and designed for a processing capacity of 3,500 lbs/hour with a maximum material density of 28.1 lbs/cubic foot. Features a dimple-style jacket rated for 250 pounds per square inch at 150 degrees F. Equipped with a 60 HP motor and leg-mounted construction. Suitable for industrial bulk material blending, mixing, and temperature-controlled processing applications. Potential applications include blending spent clay, powders, granules, dry chemicals, and other compatible bulk solid materials.

MFR: Hayes & Stolz

Unused Hayes & Stolz HR72x144SSCI 339 Cu. Ft. Industrial Ribbon Mixer – 304 Stainless Steel, 60 HP, 250 PSI Jacketed Blender

Unused Hayes & Stolz HR72x144SSCI 339 Cu. Ft. Industrial Ribbon Mixer 304 Stainless Steel, 60 HP, 250 PSI Jacketed Blender. Designed for a processing capacity of 3,500 lbs/hour with a maximum material density of 28.1 lbs/cubic foot. Features a dimple-style jacket rated for 250 pounds per square inch at 150 degrees F. Equipped with a 60 HP motor and leg-mounted construction. Suitable for industrial bulk material blending, mixing, and temperature-controlled processing applications. Potential applications include blending spent clay, powders, granules, dry chemicals, and other compatible bulk solid materials.

MFR: Hayes & Stolz

Used Meridian 3,400 Gallon Stainless Steel Vertical Storage Tank – 72" Diameter × 216" High

Used Meridian 3,400 Gallon Stainless Steel Vertical Storage Tank 72" Diameter 216" High. Top manhole. Dished Top, Slight Cone Bottom. Center bottom outlet. On (4) stainless steel legs. Serial# 6763918.

MFR: Meridian MFG

Used 3,400 Gallon (14,000 Liter) Vertical 304 Stainless Steel Tank

Used- 3,400 Gallon (14000 Liter) Tank, 304 Stainless Steel, Vertical. Approximately 86" diameter x 131" straight side.14-gauge side wall and 12 gauge top and bottom. Openings Top: 18" manway, with 2" Side port, 2" Bottom center discharge. Mounted on 6 legs. No manufacturers tag.