Chemical Equipment
Stock No.:
50467040Used Ketema MVHT-1-A-SS Shell & Tube Heat Exchanger – 3.2 Sq. Ft., 300 PSI
Used- Ketema Type MVHT-1-A-SS Shell & Tube Heat Exchanger, 3.2 Square Feet. (28) .375" Diameter x 14" long 316 stainless steel tubes rated 300 psi and full vacuum at 650 degrees F. carbon steel shell rated 150 psi at 400 degrees F, Size 4-Y-14. 1.5" tubes inlet/outlets, 1" shell inlet/outlets. Serial # WL-950429/A1,
MFR: Ketema
Stock No.:
114534753.5" Readco Twin Screw Continuous Processor
Used- 3.5" Readco Twin Screw Continuous Processor, model 3 1/2 HVY DU. Heavy duty design, stainless steel product contact surfaces, jacketed barrel rated 150 psi at 600 f, cored shafts with rotary units, driven by 50 hp, 460 volt motor, machine currently set up with cantilevered screws with adjustable gap ribbon die, with spare set of screw splines set up for end bearing housing, on base. Mfg. 1987.
MFR: Readco
Stock No.:
44604001Used J.H. Day Plow Type Turbulent Mixer – 304 Stainless Steel, 3.5 Cu. Ft. | High-Performance Industrial Mixer with Side-Entering Pinned Disc Mill
Used- J.H. Day Plow Type Turbulent Mixer, 304 Stainless Steel. 3.5 Cubic feet total capacity. Non-jacketed chamber approximately 20" diameter x 22" straight side. 3" Diameter shaft with blades and end scrapers. Driven by a 7.5 hp, 3/60/230/460 volt, 1800 rpm Sterling variable Speed-trol motor. Includes a side entering pinned disc mill, driven by a 10 hp, 3/60/230/460 volt, 3490 rpm motor. Top access door with a charge port, 8" center bottom outlet with a manually operated plug valve. Includes a control panel. Mounted on a carbon steel frame.
MFR: J H Day
Stock No.:
11059397Used ROSS HSM-430SC Inline High Shear Mixer with SLIM Powder Injection System – 30 HP Explosion Proof Mixing Platform
Used ROSS HSM-430SC Inline High Shear Mixer with SLIM Powder Injection System 30 HP Explosion Proof Mixing Platform. Solids (powder) / Liquid Injection Manifold (SLIM). Equipped with 3" Liquid inlet, 2.5" Powder Inlet and 3" Liquid outlet. Driven by 30 HP, 208-230/460 volt, 1760 rpm Explosion Proof (XP) Motors. Powder / Liquid Dispersing / Mixing System. The Liquid stream enters the mixer and immediately encounters the powder (solids) at the high shear zone (rotor and stator assembly). The resulting dispersion is expelled centrifugally through the stator opening at high velocity.
MFR: Ross Industries
Stock No.:
49307005Used Great Western Manufacturing Type TB, Model 611/4 Tru-Balance Screener
Used- Great Western Manufacturing Tru-Balance Screener, Type TB, 30" Diameter, Model 611/4 (QA30), 304 Stainless Steel. Approximate 500 pounds per minute with wheat flour. Approximate 30" diameter, (4) sieves. Approximate net sieving area 15 square feet. Driven by a 1.5 HP, 3/60/230/460 volt, 1160 rpm motor. 5" top opening, bottom openings: 5", 4". Mounted on a painted carbon steel frame. Serial# 3882. Built 1999.
MFR: BF Gump
Stock No.:
50388107Used IKA Works Dispax Reactor – High Shear Inline Disperser, Model DR 2000/10, 30 HP
Used- IKA Works Dispax Reactor High Shear Inline Disperser, Model DR 2000/10, Stainless Steel. Nominal flow rate 35 gallons per minute (8,000 l/h), nominal tip speed 4500 feet per minute. Driven by a 30hp, 3/60/230/460 volt, 3525 rpm motor. 2" Inlet & outlet. Unit mounted on a base. Part# P015742. Serial # 2599-12.
MFR: IKA Works
Stock No.:
50467035Used Gaspar 30-Gallon Reactor – 316L SS, 150 PSI, 5 HP Chemineer Agitator
Used- Gaspar Reactor, 30 Gallon. 316L Stainless steel construction, approximately 24" diameter x 24" straight side, Elliptical removable top, elliptical dish bottom. Internal rated 150 psi and full vacuum at 400 degrees F. Jacket rated for 150 psi at 400 degree F. Top mounted 5 hp Chemineer agitator drive with mechanical seal, 230/460 volt XP motor. Center bottom outlet. Mounted on (4) painted carbon steel legs. Serial# 495032, National Board# 821.
MFR: Gaspar Inc.
Stock No.:
51454001Used Bowen BLSA Laboratory Spray Dryer – 316 Stainless | 15–80 lb/hr | 1000°F Inlet | Atomizer | Complete System
Used- Bowen Engineering BLSA Laboratory Spray Dryer. 316 stainless steel. 30" (770 mm) diameter x 28" (720 mm) straight side x 30" (770 mm) coned bottom. Approximate evaporation rate 15-80 pounds (6.8-26.3 kgs) an hour. Atomizer. Air requirements 100 psi (6.66 bar), Inlet temperature range to 1000 degree F (537.77 degree C), side access door. Digital control panel mounted on unit. Mounted on stainless steel legs. Includes cyclone, collection jar, gas heater and blower, piping and additional infrastructure. Previous used in a Nutraceutical application. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible
MFR: Bowen
Stock No.:
51708014Macon 30" Diameter Single Deck Stainless Steel Screener
Used- Macon Screener, 30" Diameter, 304 Stainless Steel. Single deck, 2 separation. No screen. Top clamp-on cover with 8" center inlet. Driven by a approximate 1/2hp, 3/60/460 volt, 1140 rpm motor. Mounted on a painted carbon steel base.
MFR: Macon
Stock No.:
52695001Myers Engineering Single Shaft Disperser
Used-Myers Engineering Single Shaft Disperser, Model 800A-30. 2-1/4" diameter x 46" long 304 stainless steel shaft with a 14" diameter 304 stainless steel saw tooth blade. 360 Degree rotation. Air over oil lift with an approximate 48" rise, overall raised height approx 122''. Manually adjustable speed range. Driven by a 30 hp, 3/60/480 volt, 1760 rpm XP motor. Base mounted. Includes approx 450 gal carbon steel mixing can. Can measures 48" dia x 56" straight side. Distance of mixer blade to ground is 8".
MFR: Myers
Stock No.:
53228003Used GEA Niro Mobile Minor Stainless Steel Laboratory Spray Dryer | Pilot-Scale | 1–7 kg/hr | Mobile Unit
Used GEA Niro Mobile Minor Stainless Steel Laboratory Spray Dryer | Pilot-Scale | 17 kg/hr | Mobile Unit. Approximate evaporation rate of 1-7 kg/hr. (2.2-15.4 Lbs./hr.) depending on product. Niro centrifugal air operated atomizer. Approx. 800 mm (31-1/2") diameter x 915 mm (36") straight side. Chamber is lagged and clad. Electric heater, cyclone, pipework and additional infrastructure. Mounted on mobile frame on wheels. Reported in good condition. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.
MFR: Niro
Stock No.:
53452001Eirich Model PPB030 Stainless Steel Paddle Blender
Used- Eirich / American Process Paddle Blender, Model PPB030, 30 Cubic Feet Capacity, Stainless Steel. Non-jacketed trough approximately 90" long x 30" wide x 39" deep. Single shaft approximate 4" diameter with (17) paddles, approximate 11.5" x 5" x 5/8" thick. Driven by a 7.5hp (5.5kW), 3/60/230/460 volt, 1755 rpm gear motor, final rpm 61. (2) Piece top hinged cover with 44" x 30" infeed section. End bottom outlet 8" x 8" with slide gate valve. Mounted on (4) legs. Serial# 807495, Built 2016. Last used in shredded cheese application. 3/60/460 Volt.
MFR: American Process Systems
