Adhesive and Sealant Equipment

Used Donaldson Torit CPV-1 Industrial Dust Collector with Hopper

Used Donaldson Torit CPV-1 Industrial Dust Collector with Hopper. Up to 700 cfm, 90-100 psig. (1) filter pack. 1.5 HP. 3/60/208-460V motor.

MFR: Donaldson

Pre-Owned Donaldson Torit CPV-1 Dust Collector – 700 CFM

Pre-Owned Donaldson Torit CPV-1 Dust Collector 700 CFM, 90-100 psig. (1) filter pack. 1.5 HP. 3/60/208-460V motor. With hopper

MFR: Donaldson

Donaldson Torit CPV-1 Compact Dust Collector for Industrial Use

Donaldson Torit CPV-1 Compact Dust Collector for Industrial Use. Up to 700 cfm, 90-100 psig. (1) filter pack. 1.5 HP. 3/60/208-460V motor. With hopper

MFR: Donaldson

Used Donaldson CPV-1 Dust Collector with Filter Pack & Hopper

Used Donaldson CPV-1 Dust Collector with Filter Pack & Hopper. Up to 700 cfm, 90-100 psig. (1) filter pack. 1.5 HP. 3/60/208-460V motor. With hopper

MFR: Donaldson

Donaldson Torit CPV-1 Industrial Dust Collector – Used & Reliable

Donaldson Torit CPV-1 Industrial Dust Collector Used & Reliable. Up to 700 cfm, 90-100 psig. (1) filter pack. 1.5 HP. 3/60/208-460V motor. With hopper

MFR: Donaldson

Industrial Water Temperature Controller – Delta T ESW-09C 9KW

Used Delta T Systems Model ESW-09C Water Temperature Control Unit. 9 KW Heating capacity. 3/4 HP Pump. Approximate temperature range 32F to 230F (0C to 110C). Mounted on casters for mobility. Serial# 202167-1-1-1. 3/60/208 Volt, 35.5 Amp.

Used Glatt WSG 500 TC Fluid Bed Dryer – Stainless Steel Construction

Used- Glatt Fluid Bed Dryer, Type WSG 500 TC, Serial# 6999, Stainless Steel Construction. Includes bowl cart, Glatt LD500 lift, panels & valves.

MFR: Glatt

Used Glatt Industrial Stainless Steel Fluid Bed Dryer, Type GPCG 300.

Used- Glatt Industrial Stainless Steel Fluid Bed Dryer, Type GPCG 300. Includes bowl cart and has Glatt-made lift, model LD500. Built 2000.

MFR: Glatt

Used Glatt CPCG 5 Fluid Bed Dryer – Stainless Steel – Spray Granulation – Steam Heated – 5.5 kW Blower – 1996

Used- Glatt Fluid Bed Dryer Model CPCG 5. Stainless steel construction with spray granulation and drying inserts, 2 bar shock rating, 5.5 kw blower, 460 volt, steam heated with control panel, serial 6345. Built 1996.

MFR: Glatt

Used Extru-Tech E-325 Single Screw Extruder – 150-800 Lbs/Hr

Used- Extru-Tech Model E-325, Single Screw Extruder. Unit designed primarily for research and development purposes. 3.25", Approximately 40 HP motor, Can process between 150 to 800 pounds per hour (68 to 363 kilograms per hour). The E-325 is equipped with a 6x30 single-shaft conditioner, an accurate feed system, a knife drive, and a control panel with a variable frequency drive (VFD) panel operating at 230 volts.

MFR: Extrutech

Used Olson / V-RAM Double By-Products Pumping System | 5,000 lbs/hr | Dual 50 HP Hydraul

Used Olson Mfg. Co. dba V-RAM Pumps Double By-Products Pumping System. (2) Identical Stainless Steel Pumps, approximately 5000 lbs/hr working capacity, with 679 max psi per each pump. 30-1/2" long x 14" wide x 15-1/2" deep infeed. Approximately 54" long trough with 11" ram head. 6" diameter outlet with gate valve, 10" discharge height. Includes Double B-Style Hydraulic Unit skid with air cooler. (2) 50hp 3/60/230/460v 1775rpm motors. Includes Control Panel.

Valmet Pre-Compression Plug Feeder & Shredder System – 1000 BDST/D Biomass Capacity

Unused Valmet Plug Screw Feeder with Pre-Compression Screw and Shredder. Designed for infeed raw material chips density 100 kg/m3, moisture content 20-48%, design flow rate 530 dry tons per day soft wood chips, (500BDST/D); Max capacity 1000 BDST/D; Turndown rate 50%. Valmet plug screw feeder: Fed by a pre-compression screw section, and 48" shredder at outlet; 850 HP Siemens motor 1750 rpm 460v 3/60; Gear Reducer ratio 25:1. Nominal speed 69 rpm, range 35-105 rpm; Inlet 35.83" x 25.79". Pre-compression screw: Materials of construction stainless steel 304L for all contact parts; Sits on top of plug screw at 90 degrees with s 24" diameter top force feed; Capacity Volume/Revolution inlet/discharge: 45 L / 22.5 L. Capacity / revolution at 110 kg/m3 = 5.46 BDST/D and net max capacity at 110 kg/m3 = 530 BDST/D; 250 HP motor 1750 rpm 460v 3/60 v-belt drive to gear reducer V-belt reduction 1:52; Gear reducer SEW Eurodrive ratio 18:1. Final rpm nominal speed 65 rpm, range 45-97 rpm; Outlet: 35.83" x 25.79". T-Pipe 48" Shredder: Fed from plug screw feeder 24" biomass inlet; MAWP 350 psig at 800F; 100 HP motor 1750 rpm 460v 3/60; Gear reducer 8.9:1 for nominal 197 rpm; Outlet 24" flange 600#. All equipment never used, new in 2020. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.