Adhesive and Sealant Equipment

Used – SEITZ ORION 100/200 Stainless Steel Filter Press – 48 m² Filtration Surface, Brewery Application

Used SEITZ ORION 100/200 Stainless Steel Filter Press 48 m Filtration Surface, Brewery Application. With a 150 hl/hour (3962.5 US gallon/hour). Currently fitted with 24 chambers & 2 end plates 1000 x 1000 mm (39" x 39"). Current filtration surface is 48 m2 (516.66 sq. ft.). Hydraulic operated. On 4 legs. Includes: (1) Kieselguhr preparation tank with agitator, (1) Dosing pump, (1) GEA beer pump, (1) Hopper with geared endless screw, Diaphragm pump for kieselguhr discharge and additional infrastructure. Previously used in a brewery application. Asking price includes proper marking, dismantling and loading to truck at location.

MFR: Seitz Orion

Used Glatt 18" Wurster Insert for GPCG-30 Fluid Bed Dryer – Coating & Granulation

Used- Glatt 18" Wurster For A Model GPCG-30 Fluid Bed Dryer.

MFR: Glatt

Used Elizabeth Hata HT-AP55-DU Rotary Tablet Press – 55 Stations, 15 HP Motor

Used- Elizabeth Hata Tablet Rotary Press, Model HT-AP55-DU. (55) Filling Stations, approximate 1-1/4" diameter x 2-1/2" deep. Driven by 15 hp 3/60/230/460V, 1780 rpm gear motor through reducer, Ratio 1:12.25. Has Mitsubishi A500 Control. Includes portable control cabinet and a skid of misc. parts. Serial# I/67.

MFR: Hata

Used Nu-Con Model NCVR-18-8-3T Stainless Steel Tank

Used-Nu-Con Model NCVR-18-8-3T Stainless Steel Tank. Unit is mounted on casters, serial number: N08060-GA-106. 304 stainless Steel, interior ground to a #4 150 grit finish. No cover. Has a 24" discharge height from floor to the bottom of the flange.

Unused Roth High-Pressure Multi-Stage Pump – Model 105TEGH9487BL

Unused- Roth High Pressure Multi-Stage Pump, Model 105TEGH9487BL. Serial# 63625.

MFR: Roth

Used Fluid Air Fluid Bed Dryer Granulator

Used- Fluid Air Fluid Bed Dryer Granulator, Model 0020. 316 Stainless steel product contact parts, currently set up with dryer chamber, chamber designed to handle Wurster coating with change parts, electrically heated with 12 kw heater, blower, with on board plc controls with HMI interface, 575 volt. Serial # 10169. Built 1999.

MFR: Fluid Air

Used Econotherm GG1922/CS/S/S Industrial Heat Pipe Heat Exchanger – 1.92 MW

Used- Econotherm Model GG1922/CS/S/S Industrial Heat Pipe Heat Exchanger / Waste Heat Recovery System Designed for Southwire Company (2025) Econotherm (UK) Ltd., Model GG1922/CS/S/S industrial heat pipe heat exchanger and waste heat recovery system, engineered and designed for Southwire Company LLC for recovery of thermal energy from high-temperature industrial exhaust gases. The system utilizes Econotherm's proprietary sealed heat pipe technology to transfer waste heat from hot process exhaust gases to a separate incoming fresh-air stream, providing energy recovery without direct mixing of the two air streams. Designed to improve overall thermal efficiency, reduce fuel and energy consumption, and lower industrial operating costs by capturing heat that would otherwise be discharged to the atmosphere. The heat exchanger is designed for a nominal heat recovery capacity of approximately 1,921,553 watts (1.92 MW), equivalent to approximately 6.56 million BTU/hr, with an exhaust gas mass flow rate of 42,640 kg/hr (approximately 94,005 lb/hr) and fresh-air mass flow rate of 40,690 kg/hr (approximately 89,706 lb/hr). Under the specified operating conditions, the system is designed to receive exhaust gases at approximately 260C (500F) and reduce their temperature to 113C (235F), while simultaneously heating incoming fresh air from approximately 38C (100F) to 207C (405F). Designed for continuous industrial operation with a minimum anticipated equipment design life of 20 years. The heat recovery assembly incorporates a heavy-duty carbon steel casing with insulated construction and multiple heat pipe banks manufactured from ASTM A179 cold-drawn seamless carbon steel tubing. The individual sealed heat pipes utilize specially prepared water as the internal working fluid, providing efficient thermal transfer through a continuous evaporation and condensation cycle. The heat pipe arrangement provides heat transfer between the exhaust gas and fresh-air streams while maintaining

Used Glatt GPCG-5 Fluid Bed Dryer – 22L Capacity, Wurster Inserts Included

Used- Glatt Fluid Bed Dryer, Model GPCG-5. 22 Liter capacity. Worster insert 7" = 9.6 liter, 9" = 18 liter. Includes laptop computer, manuals and drawings.

MFR: Glatt

Used Industrial 50 Ton Tomco Model E CO2 Tank

Used- Industrial 50 Ton Tomco E CO2 Tank. Year 1991. Steel: SA-612. MAWP: 350PSI. Product: Carbon Dioxide.

MFR: Tomco

Industrial Unused - Wilfley Model A7 304L Stainless Steel Pump, 3x1.5x13, 200 GPM, 30 HP

Unused- Wilfley Pump, Model A7, 304L Stainless Steel. Size 3x1.5x13. Approximate 200 gallon per minute. 140 Foot head. Driven by a 30 hp, 3/60/460 volt, 1775 rpm motor. Jacketed casing. Serial # A703032. Built 2018.

MFR: Wilfley

Unused - Teikoku Model F61-215C4DM-0405SS1-AV 304L Stainless Steel Pump, 3.5 GPM, 30 Ft Head

Unused- Teikoku Pump, Model F61-215C4DM-0405SS1-AV, 304L Stainless Steel. Approximate 3.5 gallons per minute. 30 Foot head. Driven by a 1.7 kW motor. For use in Nitric Acid.

MFR: Wilfley

Unused Tequatic Plus F-150 Filter B-Series Skid – High Solids Filtration System

Unused- Tequatic Plus F-150 Filter, B-Series Skid. 80-240 GPM flow rate; 100 psi Maximum Inlet Pressure; 140 degrees F Maximum Temperature; 45 degrees F Minimum Temperature; pH 5-9 continuous; 1/16" Maximum Particle Size. Can handle high TSS from 10010,000 mg/L and greater, and filter down to 15 microns. 3/50-60/440V, 20 Amps. Approximately 2330 pounds dry, 3230 pounds wet.