Used Machine Tools

Stock# 50182001

Used- TREK Triton In-Line Aqueous Cleaning System. 1 Mil SMT. Approximately 14' long x 5'6" wide x 7' high. 460 volts, 3 phase at 60 Hz, 100 amps. Input water line is 1" NPT, regulated to about 70 psi. Drain is 2" direct or 1-1/2" from optional sump pump. (2) Exhaust ducts, 8-3/4" I.D. at 600 CFM each at 1-1/2" to 3" of static pressure. Metal belt is considered double wide at 12" and runs continually.

Stock# 50283001

Used Permaboss Debossing Press; Model NGL 13; Thirteen Ton Hydraulic Heated Press with Foot Switch; (4) Light, Infrared Location and Alignment Lights; Rotating Table; Last used for debossing apparel and leather goods; Mfg. 2012

Stock# 50309001

Used Heim Rousselle Tow Point Straight Side Stamping Press. 150 Tons, Model S2. Near Bottom Stroke, Twin Drive (Crankshafts), 60 Strokes per minute, 4" Stroke. Bed size 72" x 42". Bolster Area 72" x 42", 3" Bolster. Bed Opening 48" x 21". Slide Area 72" x 42", 4" Slide Adjustments. 18" SDAU Shut Height above Bed, 15" SDAU Shut Height above bolster. 77.5" Distance between LR uprights. 34" Floor to top of bed, 37" floor to top of bolster. 25 hp. Floor Space 122" x 74". 148" Overall Height; 440/3/60 volts. Approximately 30,000 pounds. Mfg. 2013. Reported to be reconditioned.

Stock# 49791001

Used- 13 Stand LMF Rollformer, Model LMF 914.13.1. Includes hydraulic pump and shear. Computerized PLC, swivel control box. Mfg. 2016.

Stock# 50538001

Used Juki Selective Solder System, Model 400L. Three-stage inline system, 4mm to 30mm diameter soldering nozzles, Drop Jet, Spray Fluxer, Pressurized Tank, Pre-Heater.

Stock# 50579001

Used- IPG Photonics Compact Fiber Laser System with Bar Feeder. Model SYS-MN-RL222XE01G0A2. Year 2017.

Stock# 50416001

Used- Haas Super Mini-Mill CNC Vertical Mill. Table/Pallet size 36" x 12". X-travel 16", Y-travel 12", Z-travel 10". Spindle rpm is 15,000 maximum, spindle taper type CAT#40, spindle motor 15hp. Tool magazine capacity 10, tool changer type Umbrella. Programmable coolant, Chip auger, Renishaw probing system, Expanded Memory, Rigid tapping, Macros. Year 7/06.

Stock# 50054001

Used- HAAS VF-5/50 Vertical CNC Milling Machine. Table/pallet size 54" x 24", maximum load 4,000 pounds. X-travel 50", Y-travel 26", Z-travel 25". Rapid traverse 710 IPM. Cutting feed rate 500 IPM. Spindle taper type CAT#50, spindle speed 10,000 rpm, 30 hp spindle motor. 30.1 Tool magazine capacity. Tool change time 4.2 seconds, chip to chip time 6.3 seconds. Liquid cooled, 95 gallon coolant capacity. T-slot width 0.630", center distance 3.15", number of Std T-slots 7. 220 VAC, 70 A. Built 2003.