Used Plastics Equipment for Sale
Used plastics equipment includes a wide range of processing systems designed for manufacturing, compounding, forming, and recycling plastic materials. These machines support critical operations such as extrusion, injection molding, pelletizing, size reduction, and film production. Commonly used across plastics manufacturing, packaging, automotive, and recycling industries, plastics equipment enables efficient material processing and consistent product quality. Aaron Equipment offers a large inventory of used plastics equipment in various configurations to meet production requirements, material types, and throughput demands.
Stock No.:
54513001Used Leistritz ZSE18HPe-P Twin Screw Co-Rotating Extrusion Pelletizing Line
Used Leistritz Twin Screw Co-Rotating Extrusion Line consisting of: (1) Leistritz Type ZSE18HPe-PH-40D Extruder, (2) 18 mm screws, approximately 40 to 1 L/D ratio, 1200 rpm maximum screw rotation, 8 zones electrically heated, water cooled, 9.4 kW drive, Machine # 3878, Built 2009. (1) Thermo Scientific Pharma 16 Varicut Pelletizer, Serial # 7.11/000094, Built 2011. (2) K-Tron Feeders, Model K-SFS-24. (2) stainless steel water bath sections each 9" wide x 115" long
MFR: Leistritz Corporation
Stock No.:
54037006Pre-Owned Killion KL-075 Single Screw Extruder – Electrically Heated, Air-Cooled
Used Killion KL-075 Single Screw Extruder. 19.1 mm Diameter screws. 25:1 L/D. Screw speed 12-120 RPM via a gearbox by a 1.1 kW-380 volt/50cycle/3Ph DC motor. 3 housing sections. Electrically heated, air cooled. Feed hoppers, control/operating panel and additional infrastructure. On wheels. Serial # 19707. In an R&D application. Over all dimensions: 42.9" (1100 mm) long x 35.1" (900 mm) width x 58.5" (1500 mm) high. Weight 660 lbs (300 kgs). Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.
MFR: Killion
Stock No.:
54400001Prism VARICUT 24 Pelletizing Line with TSE 24TC Extruder
Used Prism Pelletizing Line. Consists of: Prism parallel twin screw extruder, model TSE 24TC, 24 mm co rotating screws, 25:1 l/d, electrically heated, water cooled barrel, (3) top vents with (2) plugged, 6 barrel zones with on board control panel, 3.7 kw, 230 volt ac motor drive with VFD controller, two hold stand die, serial# 2078. (1) screw feeder with .26 kw motor drive with agitated hopper. (1) Material hopper. (1) Prism water bath pelletizer unit, model VARICUT 24, with approximately 8" x 8" x 59" long stainless steel water bath, 2.5" wide air wipe with blower, 2 5/8" wide stand pelletizer with pull rolls, helical rotor, 1.1 kw motor drive. Serial# 2077, built 1996.
MFR: Prism
Stock No.:
53393005Used – Trola-Dyne Hydraulic Power Pack Skid XL-1058 – 3000 PSI, 1 HP Motor, Control Panel
Used- Trola-Dyne Hydraulic Power Pack Skid, Part# XL-1058. 2.5 Gallon Bladder rated for 3000 PSIG. Driven by a 1hp 3/60/460v 1725rpm motor. Mounted Control Panel. Serial# FSCM#8W625. Mounted on a Carbon Steel Plate.
Stock No.:
51849001Buss Model MKS 30 Laboratory Ko-Kneader Extruder
Used- Buss Model MKS 30 Laboratory Ko-Kneader Extruder, Serial# 97-1030 (1997). 30mm Diameter x approximate 17" long single screw. Throughput rates up to 30kg per hour. 3 Zone barrel electrically heated, water cooled. Water cooled feed throat with hopper. Driven by a 10 hp, 3/60/230/460 volt, 1740 rpm AC motor with reducer. Includes a discharge screw extruder, driven by an approximately 1.5 kw, 3/60/230/460 volt, 1710 rpm gear motor with 2 hole strand die. Includes an operators panel, a control panel with Eurotherm controllers, (2) ABB drive panels. 837 Hours used on the meter.
MFR: Buss
Stock No.:
10755179Used Davis Standard 1.5" Extruder – Model 150IN DS-20, 24:1 L/D, Vented Barrel, 50 HP Gearbox
Used- Davis Standard 1.5" Extruder, Model 150IN DS-20. 24:1 L/D vented barrel at a 42" centerline. Davis Standard 6.53:1 gearbox rated for 50 HP with a service factor of 1.25 for a 152 RPM screw speed. Gearbox was manufactured in 1998. Non-tagged motor is driven by a Reliance model GV3000 A/C drive. Includes unitized temperature control panel and 4-hole strand die on barrel. Year 1984.
MFR: Davis Standard
Stock No.:
54598001Used Coperion Werner & Pfleiderer ZSK 40 Twin Screw Extruder
Used Coperion-Werner & Pfleiderer 40mm Co-Rotating Twin Screw Extruder, Type ZSK 40. Extruder features a 44:1 L/D ratio, maximum screw speed of 1,200 RPM, and 150 HP motor rated for 460 VAC, 60 Hz, 3-phase power. Equipped with a Flender 1.43:1 ratio gearbox and Brunel coupler. Barrel is electrically heated and water cooled. Controls include an Allen-Bradley SLC 5/05 PLC with 120 VAC control voltage and Coperion-Werner & Pfleiderer control panel. Includes Coperion ZS-B40 side feeder powered by a 3 HP, 460 VAC, 60 Hz, 3-phase motor with an adjustable screw speed range of 44-400 RPM. Includes control cabinet and drive cabinet. Possible applications include compounding, mixing, blending, and extrusion of suitable process materials and products. Serial # 53002, Built 2005.
MFR: Coperion
Stock No.:
74055Used Sano 10” IBC Extrusion Die - Single Layer, High-Quality Film Production
Used- Sano 10" single layer blown film IBC die, 1.75" bore opening, .070 gap.
MFR: Sano
Stock No.:
74063Used Film Extrusion Die - Filmaster 10” Single Layer, .070” Gap
Used- Filmaster 10" Single Layer Blown Film IBC Extrusion Die, .070 gap.
MFR: Filmaster
Stock No.:
10755162Used Davis Standard 10" Extruder, Model 100TH100D. 38:1 L/D ratio; (8) zone electrically heated, water cooled
Used- Davis Standard 10" Extruder, Model 100TH100D. 38:1 L/D ratio; (8) zone electrically heated, water cooled and non-vented barrel at nominal 44" center-line. 15.08:1 Gearbox reduction ratio; Rated at 1800 HP at a service factor of 1.5; Gearbox currently set to be dual direct driven in back of the gearbox. Last driven by two (2) 700 HP D/C motors; Liquid cooling system with heat exchanger for gearbox protection; Trendelkamp screen changer w/ stand mounted on the extruder discharge. Temperature control panel and drives included. Motors available at additional cost. Temperature controllers not included. Serial# L3201. Built 1991. Last used in the extrusion of biaxially oriented PP film.
MFR: Davis Standard
Stock No.:
10151570Used – Leistritz ZSE 100 GLAAX 100mm Co-Rotating Twin Screw Extruder
Used Leistritz ZSE 100 GLAAX 100mm Co-Rotating Twin Screw Extruder, Driven by 330 kw (442 hp), 1600 rpm DC motor with SCR control. Has 300 rpm screw speed, rated at 5000 Newton meters per shaft torque capability and electrically heated water cooled vented barrel. Has twin screw side feeder. Has 7515.6 hours on the hour meter. Includes spaghetti strand die, and temperature control panel. Serial #3092, Built 2002.
MFR: Leistritz Corporation
Stock No.:
44496008Used Cumberland Granulator, Model 18 x 37
Used-Cumberland Model 18X37 Granulator with 18" x 37" feed throat, designed for film granulation. Features a 5-knife steep angle step adjustable rotor with 10 knife segments and (2) bed knives. Belt driven by a 100 HP, 460 Volt, 1780 RPM motor with gravity discharge. Equipped with a 6" diameter x 37" wide knurled and grooved offset feed roll with pneumatic pinch and feed roll trumpet. Feed rolls are chain and sprocket driven by a 7.5 HP, 1750/1930 RPM continuous duty DC motor through a Reliance 2.76:1 gearbox. Mounted on leg base with swing-out chamber door on the downstroke side for chamber access. Starter and controls not included. Suitable for granulating film materials and plastic scrap for recycling and reprocessing applications.
MFR: Cumberland
Types of Used Plastics Equipment Available
Aaron Equipment offers a wide selection of used plastics equipment designed to support extrusion, molding, compounding, pelletizing, and recycling processes across a variety of polymer materials and production requirements:
Single Screw Extruders – Widely used extrusion systems for processing thermoplastics into film, sheet, pipe, and profile products.
Twin Screw Co-Rotate Extruders – High-performance compounding extruders designed for precise mixing, blending, and material modification.
Injection Molders – Horizontal – Standard molding machines used for high-volume production of plastic parts with consistent precision.
Pelletizing Machinery – Strand Pelletizers – Systems used to cut extruded plastic strands into uniform pellets for downstream processing or sale.
Size Reduction – Grinders and Granulators – Equipment designed to reduce scrap plastic into reusable material for recycling and reprocessing.
Blown Film Lines – Complete systems for producing plastic films used in packaging, bags, and flexible materials.
Plastics Equipment Applications & Industry Uses
Used plastics equipment supports a wide range of manufacturing and recycling operations where plastic materials must be formed, processed, or reconditioned. Common applications include:
Packaging Manufacturing: Production of films, bags, containers, and flexible packaging materials
Automotive & Industrial: Molding and extrusion of durable plastic components and parts
Recycling Operations: Size reduction, washing, and pelletizing of post-industrial and post-consumer plasticsConstruction Materials: Production of pipe, profiles, insulation, and structural components
Consumer Goods: High-volume manufacturing of plastic products and housings
These systems play a critical role in maintaining material consistency, throughput efficiency, and product quality across plastics processing operations.
Used Plastics Equipment Buying Considerations
When selecting used plastics equipment, it is important to evaluate both process requirements and equipment condition:
Material Compatibility: Ensure equipment supports specific polymers such as PE, PP, PVC, PET, or engineered resins
Process Type: Determine whether extrusion, molding, pelletizing, or recycling systems are required
Throughput & Output Capacity: Match machine performance with production targets
Screw & Barrel Design: Critical for mixing efficiency, melt quality, and product consistency
Control Systems & Automation: Evaluate PLC systems, controls, and integration capabilities
Condition & Maintenance History: Review wear components, rebuild status, and prior application.
Why Buy Used Plastics Equipment
Buying used plastics equipment provides a cost-effective solution for expanding production capacity or upgrading existing processing lines. Used systems reduce capital investment while offering proven, industrial-grade performance. Many machines are available for immediate shipment, helping facilities avoid long lead times and maintain production schedules.
With access to a wide range of equipment types and manufacturers, Aaron Equipment helps processors find reliable plastics machinery tailored to their specific operational needs.
Sell Your Used Plastics Equipment
Aaron Equipment actively purchases surplus plastics equipment, including extrusion systems, injection molding machines, and recycling lines. Whether you are upgrading equipment or liquidating assets, our team can help maximize equipment value.
Plastics equipment is used to process, form, and recycle plastic materials through operations such as extrusion, injection molding, pelletizing, and size reduction. These systems are essential in manufacturing and recycling environments.
Common types include extruders, injection molding machines, pelletizers, shredders, grinders, and film production lines. Each type supports a specific stage of plastics processing or recycling.
Choosing the right equipment depends on material type, production volume, and process requirements. Evaluating machine configuration, throughput, and compatibility with existing systems is critical.
Yes. Many plastics machines are built for long service life and can remain highly reliable when properly maintained, inspected, or refurbished prior to purchase.
Plastic recycling systems typically include shredders, grinders, wash lines, and pelletizers that convert scrap plastic into reusable raw material for reprocessing.