Waste Water Equipment

HSI NT88408 Multi-Stage Centrifugal Blower System for Industrial Air Movement and Process Gas Applications

HSI NT88408 Multi-Stage Centrifugal Blower System for Industrial Air Movement and Process Gas Applications. S/N 2131006A-5. 10' inlet, 8" outlet, POS.1 vertical. Blower casing is cast iron with heresite P403L coating. Shaft material is 4140 carbon steel. Has labyrinth seals and brass deflector. Impeller is 5011 CAST B.C. at wheel #1 and 5021 CAST RAD. at wheel #2 thru 11. Unit mounted on 25' X 130" skid with 449TS HSI standard motor base. Powered by 300 HP TECO 3/60/460 volt motor.

MFR: HSI

Blue Star VD300-01 300 kW Diesel Generator – 480/277V Standby Power Unit

Used Blue Star Power Systems Model VD300-1 300 kW Standby / 275 kW Prime Diesel Generator Set With Volvo Penta Engine, Built 2018. Low-hour diesel generator rated for 300 kW standby power and 275 kW prime power, powered by a Volvo Penta Model TAD1351GE diesel engine rated at 456 HP at 1,800 RPM. Engine meets EPA Tier 3 emissions standards. Generator produces 277/480 volts, 3-phase, 60 Hz electrical output and features a 12-lead reconnectable alternator for alternative voltage configurations. Equipped with a 400-amp main-line circuit breaker, permanent magnet generator (PMG) excitation system and Basler DGC-2020 digital generator control panel. Additional features include an engine coolant heater, weather-protective enclosure and UL-listed sub-base diesel fuel tank with secondary containment. Generator assembly is UL listed for stationary power applications. Unit has approximately 121.4 recorded operating hours. Generator Serial #103448-1-1. Volvo Penta Engine Serial #2013746570. Manufactured in 2018. Possible applications include standby and emergency backup power generation for manufacturing facilities, warehouses, commercial buildings, water treatment facilities, agricultural operations, telecommunications infrastructure and other suitable industrial or commercial facilities requiring reliable 300 kW diesel-powered electrical generation.

MFR: Blue Star Power Systems

Used Generac MG0300 300 kW Natural Gas Generator – 277/480V Enclosed Genset with

Used 2012 Generac natural gas generator, model MG0300, rated at 300 kW. Unit is powered by an enclosed OH0924 engine and has 160 reported operating hours. Generator is configured for 3-phase, 60 Hz, 277/480V electrical service and includes a weather enclosure, Eaton inline 630 amp breaker, and coolant heater. Serial number 2114542. Possible applications and suitable uses include standby or backup power for industrial facilities, manufacturing plants, warehouses, commercial buildings, and other operations requiring 300 kW, 277/480V 3-phase power. OAD 174" X 57" X 75"T, 8,300 LBS.

MFR: Generac

3000 Gallon Jacketed Stainless Steel Dish Bottom Mix Tank

Used- 3000 Gallon Jacketed Stainless Steel Dish Bottom Mix Tank. 8' Dia. X 7' T/T. Half Pipe Stainless Steel Jacket. 2 HP, 230/460 volt Lightnin Series 10 Mixer. 3" Center bottom outlet with valve. Has slight cone top. Mounted on legs. Last used in Health/Nutritional/Biomedical Collagen products.

Used Dairy Craft 30,000 Gallon Stainless Steel Insulated Storage Tank | 304 SS | Jacketed | Agitator-Ready | Milk Processing

Used Dairy Craft 30,000 Gallon Stainless Steel Insulated Storage Tank | 304 SS | Jacketed | Agitator-Ready | Milk Processing Dome top, flat sloped bottom. Dimple jacket runs partway up the shell. Insulated. Side bottom hinged manway - doghouse. Provision for a side-mounted agitator in the manway - doghouse. Lifting lugs on the top dome head. Previously used for milk.

MFR: Dairycraft

Used Mueller 30,000 Gallon Stainless Steel Insulated Dairy Silo – Vertical Milk & Whey Storage Tank

Used Mueller 30,000-Gallon Vertical Stainless Steel Insulated Dairy Silo. Manufactured in 1996. Silo measures 140" internal diameter x 518 1/8" overall height, with approximately 146 1/2" outside diameter and 151 1/4" base outside diameter. Unit features a side bottom manway, agitator assembly, overflow/vent line, CIP supply line, and refrigeration connections. Previously used for whey. Possible applications and suitable products include dairy and food processing storage for whey and similar liquid products.

MFR: Mueller Corp

Ketema 32" x 20" Mark III Perforated Basket Centrifuge.

Used- Ketema 32" x 20" Mark III Perforated Basket Centrifuge. Stainless steel construction (product contact areas); Top load, bottom unload with hydraulic plow discharge; Max bowl speed 1325 rpm; Rated 96#/cu. ft. capacity, Unit is on 33.5" heavy duty leg extensions; Top cover is sealed and air tight, includes hinged access door; 20 HP hydraulic drive; 3 phase, 230/460 voltage; Includes set of stairs with platform for operator. Previous customer ran with a nitrogen blanket.

MFR: Ketema

Used 3,200 Gallon Stainless Steel Tank – Vertical Dished Vessel with Multiple Po

Used- Stainless Steel Vertical Storage Tank, Approximately 3,200 Gallon Capacity. Approximately 88" diameter x 120" straight side. Tank features dished top and bottom heads, (2) 4" top openings, (4) 2" top openings, a 2" lower side outlet, a 3" bottom outlet, and a 4" center bottom outlet with approximately 32" discharge height. Equipped with a lower side manway with cover and supported by (4) stainless steel legs. Manufacturer identification tag not present. Possible applications include liquid storage, intermediate bulk storage, and batch holding of water, liquid ingredients, chemicals, and other compatible non-pressurized liquid products.

Unused CECO Peerless 324 Gallon 316 Stainless Steel Vertical Oxygen Separator Vessel | ASME Pressure Vessel

Unused CECO Peerless 324 Gallon 316 Stainless Steel Vertical Oxygen Separator Vessel | ASME Pressure Vessel. 42" ID Vertical Oxygen Separator, PMC Part No. VGSP-42I-380SS-001, Drawing No. 9558B-1, is a heavy-wall vertical ASME pressure vessel designed for high-pressure oxygen service and deflagration control applications. Fabricated entirely from 316 stainless steel in accordance with ASME Section VIII Division 1, 2023 Edition, the vessel is rated for full vacuum to 380 PSIG at 194F with a MAWP of 380 PSI at 194F, a MAP of 380 PSI at 100F, and an MDMT of -4F at 380 PSI. The separator is fully ASME U-stamped and National Board registered, requires RT1 radiography, and is hydrostatically tested to 494 PSI for one hour with no PWHT required. Construction includes a 1/2" thick SA-240-316 shell, 1/2" thick 2:1 ellipsoidal heads with 0.4024" minimum formed thickness, heavy-wall Schedule 160 drain and liquid outlet nozzles, reinforced manway assembly, four support legs, lifting lugs, and a davit arm assembly. The vessel includes multiple flanged process and instrumentation connections consisting of 2" inlet, liquid inlet, and outlet nozzles, 3" liquid outlet and drain nozzles, a 2" gas purging connection, 1" DPIT, pressure indicator, vent, and relief valve nozzles, dual 3/4" level gauge connections, dual 1" level controller connections, four 1" level switch connections, and an 18" Class 300 manway. Internal surfaces are oxygen cleaned with neoprene gaskets and flange covers installed for shipment, while the exterior is cleaned, de-scaled, and finished with a sugar blast coating. Estimated vessel weights are approximately 2,412 lbs empty, 5,154 lbs operating, and 5,163 lbs hydrotest weight, with an internal capacity of approximately 324 gallons and a center of gravity located 13.12" from datum. The engineering design package includes ASME VIII Division 1 stress calculations, nozzle reinforcement analysis, hydrostatic test verification, wind and seismic analysis, structural support calculations

MFR: Peerless

Unused CECO Peerless 316 Stainless Steel Oxygen Separator Pressure Vessel | 380 PSI ASME Vessel

Unused CECO Peerless 316 Stainless Steel Oxygen Separator Pressure Vessel | 380 PSI ASME Vessel. 42" ID Vertical Oxygen Separator, PMC Part No. VGSP-42I-380SS-001, Drawing No. 9558B-1, is a heavy-wall vertical ASME pressure vessel designed for high-pressure oxygen service and deflagration control applications. Fabricated entirely from 316 stainless steel in accordance with ASME Section VIII Division 1, 2023 Edition, the vessel is rated for full vacuum to 380 PSIG at 194F with a MAWP of 380 PSI at 194F, a MAP of 380 PSI at 100F, and an MDMT of -4F at 380 PSI. The separator is fully ASME U-stamped and National Board registered, requires RT1 radiography, and is hydrostatically tested to 494 PSI for one hour with no PWHT required. Construction includes a 1/2" thick SA-240-316 shell, 1/2" thick 2:1 ellipsoidal heads with 0.4024" minimum formed thickness, heavy-wall Schedule 160 drain and liquid outlet nozzles, reinforced manway assembly, four support legs, lifting lugs, and a davit arm assembly. The vessel includes multiple flanged process and instrumentation connections consisting of 2" inlet, liquid inlet, and outlet nozzles, 3" liquid outlet and drain nozzles, a 2" gas purging connection, 1" DPIT, pressure indicator, vent, and relief valve nozzles, dual 3/4" level gauge connections, dual 1" level controller connections, four 1" level switch connections, and an 18" Class 300 manway. Internal surfaces are oxygen cleaned with neoprene gaskets and flange covers installed for shipment, while the exterior is cleaned, de-scaled, and finished with a sugar blast coating. Estimated vessel weights are approximately 2,412 lbs empty, 5,154 lbs operating, and 5,163 lbs hydrotest weight, with an internal capacity of approximately 324 gallons and a center of gravity located 13.12" from datum. The engineering design package includes ASME VIII Division 1 stress calculations, nozzle reinforcement analysis, hydrostatic test verification, wind and seismic analysis, structural support calculations

MFR: Peerless

Used Meridian 3,400 Gallon Stainless Steel Vertical Storage Tank – 72" Diameter × 216" High

Used Meridian 3,400 Gallon Stainless Steel Vertical Storage Tank 72" Diameter 216" High. Top manhole. Dished Top, Slight Cone Bottom. Center bottom outlet. On (4) stainless steel legs. Serial# 6763918.

MFR: Meridian MFG

Used 3,400 Gallon (14,000 Liter) Vertical 304 Stainless Steel Tank

Used- 3,400 Gallon (14000 Liter) Tank, 304 Stainless Steel, Vertical. Approximately 86" diameter x 131" straight side.14-gauge side wall and 12 gauge top and bottom. Openings Top: 18" manway, with 2" Side port, 2" Bottom center discharge. Mounted on 6 legs. No manufacturers tag.