Power Generation Equipment

Used Gemini 125 HPSS CNG Gas Compressor – 4 Stage, 300 CFM, 125 HP, Complete System with Cascade, Dryer, Dispensers

Used- Gemini Gas Compressor, Model 125 HPSS, 4 Stage 300 CFM. CNG (Compressed Natural Gas) compressor system includes a four-stage, water-cooled, reciprocating compressor designed for efficient gas compression up to high pressures. U.S. Motors 125 HP, 1760 RPM, 460 Volt motor (S/N X783119) and includes an MK-AJ 24" recapture tank (S/N 9605). It is equipped with an EI C36-0527 cooler (S/N 93483) and a three-cylinder ASME cascade system, each cylinder measuring 20" x 11'6", rated for 5,000 psig and 5,711 cu. ft., with serial numbers 43338, 43339, and 43340. The unit utilizes a Marcum 11 Valve Electro-Pneumatic PMV/SMV priority/sequence panel for flow control. Compression is handled by a Quincy F340-80 air compressor rated at 7.5 HP, 460 Volt, with a discharge aftercooler (S/N 6019514). Drying is managed by a Wilkerson DE3 Twin Tower Heatless Dryer housed in a NEMA 4 enclosure (S/N 4339311). Fuel dispensing is facilitated by two DVCO 2020D dispensers with Hansen nozzles, serial numbers 930034 and 930037.and includes an air-cooled aftercooler, inter-stage separators, and safety relief valves on all stages. The compressor is skid-mounted with an integrated control panel for monitoring and automation, and it is designed for continuous-duty operation. Suitable for vehicle fueling stations or industrial applications, the unit ensures reliable performance with built-in protection systems.

MFR: Gemini

Used Atlas Copco Air Compressor & Dryer System – ZE4-B & FD 1250 VSD

Used 2013 Atlas Copco oil-free rotary screw compressor and VSD dryer package with approximately 5,000 total operating hours, complete with filtration and modern controls. Consists of an Atlas Copco Model ZE4-B Low Pressure Oil-Free Rotary Screw Compressor rated at ~876 CFM, driven by a 125hp 3/60/440-460v 3560rpm air-cooled motor, 33 psig max working pressure, with Elektronikon GraphicPlus HMI and Siemens Sinamics drive (S/N APF185963); an Atlas Copco FD 1250 VSD Refrigerated Air Dryer rated at 2,646.25 CFM, 11.8kW, R404a refrigerant with Elektronikon HMI controls (S/N APF185022); and (2) Atlas Copco DD 1400FF inline air filters with housings (S/N APF185422/423). Oil-free screw technology with refrigerated drying and inline filtration makes this package well-suited to clean-air applications in pharma, food and beverage, electronics, and any process where oil carryover is unacceptable. Turnkey, ready-to-integrate compressed-air solution rather than a bare machine. System reported in excellent working condition; documentation available, photos and inspection recommended.

MFR: Atlas Copco

Used 1,250 Gallon 304 Stainless Steel Vertical Mix Tank – Dual Turbine Agitator,

Used 1,250 Gallon 304 Stainless Steel Vertical Mix Tank. Approximate 98" diameter x 42" straight side. Flat top, slight dish bottom. Top agitator bridge with a Chemineer 2-tier 3-turbine agitator. Driven by a 1hp, 3/60/230/460 volt, 1160rpm gear motor. Openings Top: (2) 12" manways, 1-1/2". Approximately 3" center bottom outlet. (4) internal mounted baffles. Mounted on (4) Stainless Steel Legs. No Manufacturers Tag.

1,250 Gallon 304 Stainless Steel Agitated Mix Tank – Dual Turbine, Baffled, Vert

Used Agitated Stainless Steel 1,250 Gallon Mix Tank, Vertical. Approximately 98" diameter x 42" straight side. Flat top, slight dish bottom. Top agitator bridge with a Chemineer 2-tier 3-turbine agitator. Driven by a 1hp, 3/60/230/460 volt, 1160rpm gear motor. Openings Top: (2) 12" manways, 1-1/2". Approximately 3" center bottom outlet. (4) internal mounted baffles. Mounted on (4) Stainless Steel Legs. No Manufacturers Tag.

304 Stainless Steel 1,250 Gallon Batch Tank with Dual Turbine Agitator & Interna

Used 304 Stainless Steel 1,250 Gallon Chemineer Agitated Tank, Vertical. Approximately 98" diameter x 42" straight side. Flat top, slight dish bottom. Top agitator bridge with Chemineer dual 3 turbine agitator. Driven by a 1.5hp, 3/60/230/460 volt, 1175rpm gear motor. Openings Top: (2) 12" manways. Approximately 3" center bottom outlet. (4) internal mounted baffles. Mounted on (4) Stainless Steel Legs. No Manufacturers Tag.

MFR: Unknown

Used – 50 Ton Tomco C CO2 Tank – Vertical High-Pressure Carbon Dioxide Storage

Used 50 Ton Tomco C CO2 Tank Vertical High-Pressure Carbon Dioxide Storage. SA-612 Shell & Head. 78" diameter x 576" straight side. MAWP: 350PSI at 200 degrees F. 12" x 16" manway. Product: Carbon Dioxide. National Board# 1591, Serial# 1591, built 1986.

MFR: Tomco

Wolfe Mechanical Mix Tank. Approx.12,600 gallon

Used- Wolfe Mechanical Mix Tank. Approx.12,600 gallons, 304L stainless steel vertical 12' diameter X 15' high straight side. Internal rated 0.36/-0.22 PSI @ 250 degrees F. Max S.P. 1.3. Flat top with 6" channel supports and flat bottom. Top fittings: (1) 10" center agitator nozzle, (1) 2", (2) 3", and (1) 6". (1) 2" and (1) 4" side top inlets. 24" side bottom manway, (3) 3" side bottom outlets. (1) 2" low point drain. Has (3) internal baffles. Equipped with ProQuip top entering agitator model 3ZEX25BP driven by a 3 HP,3/60/230/460v 1800 RPM Motor. Heavy duty agitator drive with dry well and oversized bearings, 3" and 2" diameter x 174" long two piece shaft 304 SS, two 39" diameter 3-blade HiFlow turbines rotating at 72 RPM with lower impeller 18" off tank bottom and upper impeller 80" above lower. Each turbine pumps 18,518 GPM providing an entrained flow of 37,040 GPM. Gear reducer service factor of 1.6 based on full motor horsepower and L-10 bearing life in excess of 100,000 hours. Shaft sealed by means of low pressure Viton vapor seal with two piece split 304 SS seal plate.. Weight 7900#, Built 2010.

MFR: Wolfe Mech

Unused 12,700 Gallon Crown Iron Works 316L Stainless Steel Vertical Storage & Process Vessel

Unused 12,700 Gallon Crown Iron Works 316L Stainless Steel Vertical Storage & Process Vessel.12' diameter x 11'8" straight side. 19'2" Overall Height. Rated 15FV psi @ 250 degrees F. Lug/Leg Supports. Dished Heads. 1/4" Thick Shell Wall. 20" top manway, bottom 4" center bottom outlet.

MFR: Crown Iron Works

Used 50 Liter, Single Use Bioreactor, Manufactured by Thermo Scientific

Used- Thermo Scientific Single Use Bioreactor, Model HyClone, 50 liter(13.2 Gal) capacity, Stainless Steel. Open top, flat bottom shell. 14" diameter x 22" straight side. Dimple Jacket. Operating Temperature Range: Ambient to 40 +/- 0.1 Degrees C (104+/-0.2 DegreesF). 0.5psi Bag Pressure. Includes AB Series A Drive, Brother 3 phase induction motor, 1/4hp 3/60/208-230/460v 1720rpm, 10:1 Ratio. Mounted on Stainless Steel Frame. Serial# H10289-01.

MFR: Thermo Scientific

Used Mobile Wastewater Treatment Decanter System – Alfa Laval AVNX-4045 Centrifuge

Used- Mobile Waste Water Treatment Decanter System consisting of (1) used Alfa Laval AVNX-4045/AVNX 919B-31G Solid Bowl Decanter Centrifuge. 316 Stainless Steel construction (product contact areas). Maximum bowl speed 3250 rpm. Capacity; approximately 150 kg dry solids/hour; 6 m3/hour with 2.5 % dry solids. Single row of lined cake discharge ports, single lead conveyor, base, casing, gearbox with feed pipe, approx. 30 kw main drive motor, back drive. On 4 legs. Incl. (2) control panels, pump, piping, sensors, valves and additional infrastructure. Mounted on trailer. New year 1994. Trailer dimensions: L x W x H: 3500 mm Long x 2000 mm Width x 2140 mm high. Weight 3 tonnes. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.

MFR: Alfa Laval

Sharples/Alfa Laval Solid Bowl Decanter Centrifuge, Model DS-308 (PM38000)-Used-

Used- Sharples/Alfa Laval Solid Bowl Decanter Centrifuge, Model DS-308 (PM38000). Stainless Steel construction (product contact areas), maximum bowl speed 4000 rpm, single row of lined cake solids discharge ports, liquid plate dams, base, casing, feed pipe, gearbox, 40 hp drive motor, 15 HP VFD back drive, control panel (230-460 volts).

MFR: Sharples

Used Alfa Laval Aldec-404 Stainless Steel Solid Bowl Decanter Centrifuge

Used Alfa Laval Model Aldec-404 Solid Bowl Decanter Centrifuge With 316 Stainless Steel Product Contact Surfaces, 4,000 RPM Maximum Bowl Speed And 22 kW Main Drive. Industrial horizontal solid bowl decanter centrifuge designed for continuous solid-liquid separation, sludge dewatering, slurry clarification, solids concentration and recovery of suspended solids from compatible industrial process streams. Features 316 stainless steel product-contact construction with a maximum bowl operating speed of 4,000 RPM for centrifugal separation of suspended solids from liquid materials. Equipped with a 110 mm (4.33") single-lead internal screw conveyor with welded hardfacing for increased wear resistance during continuous solids transport and discharge. Includes a single row of lined cake discharge ports for removal of separated solids and moon-style liquid plate dams for controlling liquid discharge level and separation conditions. Fitted with a 2.5 kNm torque-rated gearbox with a 159:1 reduction ratio, a 22 kW (approximately 29.5 HP) main drive motor requiring 380 volts, 3-phase, 50 Hz electrical service, and a DC backdrive motor for controlling differential speed between the rotating bowl and internal screw conveyor. Includes supporting base, casing and feed pipe for product introduction into the centrifuge. Manufactured by Alfa Laval, Model Aldec-404. Possible applications include municipal and industrial wastewater treatment, biological sludge dewatering, chemical slurry separation, suspended solids recovery, industrial effluent clarification, food processing wastewater treatment, mineral slurry dewatering, pigment processing and concentration of other compatible solids-bearing liquid streams.

MFR: Alfa Laval