Pharmaceutical Equipment

Used 750 Gallon Stainless Steel Vertical Mix Tank – Dual Turbine & Emulsifier (N

Used 750 Gallon Stainless Steel Vertical Mix Tank, Stainless Steel. Approximately 58" diameter x 60" straight side. Dome Top, Dome Bottom. Top center entering emulsifying agitator, no drive. Top offset entering Dual 3 turbine agitator Driven by an approximate 1.17HP 3/60/208-230/460v 1725rpm motor. Openings Top: 22" for agitator, 21" manway (no cover), 3", (4) 2", 2" side bottom outlet. 3" Center bottom outlet with 6" discharge height. Mounted on (4) stainless steel legs.

Used New Brunswick Scientific Co. 3000L (750 gallon) capacity Stainless Steel Tank. National Board #569. Diameter is 48” with a 72” straight side with jacket on the lower 24". Vessel- Max Allowable...

Used-New Brunswick Scientific Co. 3000L (750 gallon) capacity Stainless Steel Tank. National Board #569. Diameter is 48” with a 72” straight side with jacket on the lower 24". Vessel- Max Allowable Working Pressure 40PSIG/O PSIA. Jacket-Max Allowable Working Pressure 35 PSIG. Vessel- Max Temp. 300°F. Jacket- Max Temp. 300°F. Vessel- Hydrotest 80 PSIG. Jacket- Hydrotest 100 PSIG. The top has a 18”RFSO with blind flange with 4” sightglass, a 2” sightglass , one-¼” plug, one-½” plug, one- ¾” plug and one-1” threaded coupling on the neck. The top of the tank has a 1-1/2” agitator shaft (no motor included), ¾” threaded coupling, ¼” threaded coupling, one-1” 150lb. Pad flange, one-4” 150lb. Pad flange, and three lift lags. The upper 24” inch portion of the tank has three-2” threaded couplings, one-3/4” threaded coupling, one-1” threaded coupling with fitting, two-1” sanitary threaded, one-2” 150lb. Pad flange with blind, and one Ametek MNG DIV. Pressure Gauge on a 1”pad flange. The lower 48” jacketed portion has three-2” threaded couplings. Below the jacket is six--1” sanitary threaded. The bottom has one--2” pad flange with blind, one-½” valve with fittings, one-1” valve with fittings, one-2” valve with fittings, and 3 lift lugs.Built 1982. Sits on four carbon steel legs. Overall Size is 132” x 80”.

MFR: New Brunswick Scientific

Used CE Howard 7,500 Gallon Stainless Steel Jacketed Tank – 304 SS

Used- CE Howard 7,500 Gallon Stainless Steel Jacketed Tank, 304 stainless steel, measures 118" diameter x 162" straight side with dome top and flat bottom. Unit has dimple jacket wrapped around bottom section of tank, 48" high, rated for 85 PSI at 300 degrees Fahrenheit to negative 20 degrees Fahrenheit. Includes (1) 4" diameter side bottom outlet, (2) 2" top ports and (3) 3" top ports with 22" x 10" manhole.

MFR: C E Howard

Unused Watson Metal Masters 7,500 Gallon 304 Stainless Steel Tank – 122" Diameter x 153" Straight Side – Built 2021

Unused Watson Metal Masters 7,500 Gallon Stainless Steel Tank, Manufactured in 2021. Constructed of 304 stainless steel with approximately 122" diameter x 153" straight side. Features a dome top, flat bottom, and 20" side bottom manway for interior access. Rated for atmospheric pressure at 100 F internal temperature. Overall height approximately 170". Manufacturer: Watson Metal Masters. Serial number: 7067-1. Suitable applications include atmospheric liquid storage, bulk ingredient holding, and process liquid storage for compatible food, beverage, chemical, and industrial liquid products.

MFR: Watson

Unused Watson Metal Masters 7,500 Gallon 304 Stainless Steel Tank – 304 SS – Built 2021 – Atmospheric Storage Vessel

Unused Watson Metal Masters 7,500 gallon 304 stainless steel atmospheric storage tank, built 2021. Approximately 122" diameter 153" straight side with dome top and flat bottom; about 170" overall height. Rated atmospheric at 100F internal. 20" side-bottom manway. Serial #7068-1. Suitable for propylene glycol and other atmospheric liquid storage.

MFR: Watson

Used 7,500 Gallon Alloy Fabricators 304L Stainless Steel Vertical Storage Tank

Used 7,500 Gallon Alloy Fabricators 304L Stainless Steel Vertical Storage Tank. Approximately 12' diameter x 9' tall. Flat top. Built 1995.

MFR: Alloy Fab

Used 7,500 Gallon Alloy Fabricators 316L Stainless Steel Vertical Storage Tank with Side Manway

Used-7,500 Gallon Alloy Fabricators Stainless Steel Tank. 316L Stainless steel. Approximately 10' diameter x 155'' tall. Side manway. Flat top.

MFR: Alloy Fab

Unused Tarmac Int. Inc. Heat Exchanger – 768 Sq. Ft., 1.8 MMBTU/H, Stainless Steel

Unused- Tarmac Int. Inc Heat Exchanger, (Never set up on the Hot side). Model 48-30DPL48-0.625-IU. 768 sqft. Stainless steel. Size: 48"*48"*54.25, CFM: 8100 CFM. Material: High temperature SST, Surface area: 768 Ft square. Total heat transfer rate: 1.8 MMBTU/Hour. Type: Plate/plate heat exchanger. Max Temp Hot Gas Inlet: 662 F. Efficient: 64.3%. Suitable to handle particulate gases from solid combustion and also applicable in clean combustion Outlet temp hot side: 249F , 11 GA. 304 S.S. casing with 18 GA. 304 S.S. expansion joints at 3 connections, 12 Ga. C.S. cladding with 3 x 3 x C S flanges primed and painted. STRUCTURAL STAND EQUAL TO OR LESS THAN 5 HEAT EXCHANGER ELEVATION. Year 2021. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.

Used Smithco Model 1F30-111-2 Four-Bundle Fin-Fan Cooler Package – Natural Gas & Lube Oil Air-Cooled Heat Exchanger System

Used Smithco Model 1F30-111-2 Four-Bundle Fin-Fan Cooler Package Natural Gas & Lube Oil Air-Cooled Heat Exchanger System. S/N 108432-B. Overall dimensions are 31.5' long X 11.1' wide X 12.67' tall. Unit consists of (2) lube oil coolers, Natural gas cooler #1 and Natural gas cooler #2. Lube cooler 1 has 3" 300# inlet and outlet and (98) 1" 304 stainless steel tubes configured in 4 rows 2-pass 30' long. Fin type L-tension aluminum. Rated 330 PSIG @ -20 to 350 F. Bare Sq ft. 770.3, Extended Sq Ft. 16,310. Natural gas cooler CLR-1 has 6" 300# inlet and outlet and (34) 1.25" 304 tubes configured in 4 rows 2-pass 30' long. Fin type L-tension aluminum. Rated 300 PSIG @ -20 to 350F. Bare Sq ft. 334, Extended Sq Ft. 6,542. Lube cooler 2 has 2" 300# inlet and outlet and (54) 1" 304 stainless steel tubes configured in 4 rows 2-pass 30' long. Fin type L-tension aluminum. Rated 450 PSIG @ -20 to 350 F. Bare Sq. ft. 424.4 Extended Sq ft 8,986. Natural gas cooler CLR-2 has 4" 300# inlet and outlet and (26) 1.25" 304 stainless steel tubes configured in 4 rows 2 pass 30' long. Fin type L-tension aluminum. Rated -20 to 350 F. Bare Sq ft. 255.4, Extended Sq. ft. 5,003. Unit has (2) 20HP COFIMCO model 49 5000 fans 10' diameter consisting of (5) aluminum blades with adjustable pitch and 10 degree angle. Motors are 3/60/460 volt. Fans driven by belt driven speed reducer. Rated 122,800 ACFM. Galvanized structure. Built 2010, Weight 22,800#.

MFR: Smithco Engineering

Smithco Four-Bundle Air-Cooled Heat Exchanger Package for Natural Gas Compression and Lube Oil Cooling Operations

Smithco Four-Bundle Air-Cooled Heat Exchanger Package for Natural Gas Compression and Lube Oil Cooling Operations. S/N 108432-B. Overall dimensions are 31.5' long X 11.1' wide X 12.67' tall. Unit consists of (2) lube oil coolers, Natural gas cooler #1 and Natural gas cooler #2. Lube cooler 1 has 3" 300# inlet and outlet and (98) 1" 304 stainless steel tubes configured in 4 rows 2-pass 30' long. Fin type L-tension aluminum. Rated 330 PSIG @ -20 to 350 F. Bare Sq ft. 770.3, Extended Sq Ft. 16,310. Natural gas cooler CLR-1 has 6" 300# inlet and outlet and (34) 1.25" 304 tubes configured in 4 rows 2-pass 30' long. Fin type L-tension aluminum. Rated 300 PSIG @ -20 to 350F. Bare Sq ft. 334, Extended Sq Ft. 6,542. Lube cooler 2 has 2" 300# inlet and outlet and (54) 1" 304 stainless steel tubes configured in 4 rows 2-pass 30' long. Fin type L-tension aluminum. Rated 450 PSIG @ -20 to 350 F. Bare Sq. ft. 424.4 Extended Sq ft 8,986. Natural gas cooler CLR-2 has 4" 300# inlet and outlet and (26) 1.25" 304 stainless steel tubes configured in 4 rows 2 pass 30' long. Fin type L-tension aluminum. Rated -20 to 350 F. Bare Sq ft. 255.4, Extended Sq. ft. 5,003. Unit has (2) 20HP COFIMCO model 49 5000 fans 10' diameter consisting of (5) aluminum blades with adjustable pitch and 10 degree angle. Motors are 3/60/460 volt. Fans driven by belt driven speed reducer. Rated 122,800 ACFM. Galvanized structure. Built 2010, Weight 22,800#.

MFR: Smithco Engineering

Used Multistack / Airstack Free Cool Chiller – Model ASP030XC13H2AS1AAAS-410A

Used Multistack / Airstack Free Cool Chiller Model ASP030XC13H2AS1AAAS-410A. Rated 78.8 tons. 206 GPM total flow rate (68.7 per module). System consists of (4) modules, (3) Free Cool chiller modules and (1) glycol feeder module with 50 gallon reservoir. R-410A refrigerant, 125lb charge per module. 3/60/460V.

Used Xylem Shell & Tube Heat Exchanger – 150 PSI Pressure Rating, Built 2018

Used 2018 Xylem horizontal U-tube heat exchanger with approximately 78 square feet of heat transfer surface. Unit has (22) 304 stainless steel 3/4" diameter tubes and an approximately 8" diameter x 108" long carbon steel shell with sheathing. Shell and tubes are rated for 150 psi at -20 to 375 F. Connections include (2) 2" shell openings, (2) 2" tube openings, 3/4" vent, and (2) 1/2" drains. Serial number 285806-03, National Board number 314565. Overall dimensions are approximately 118" x 54" x 34" tall. Possible applications and suitable products include industrial heating, cooling, heat recovery, and liquid-to-liquid heat transfer service for compatible process fluids.