Food and Beverage Equipment
Stock No.:
51781003Used Double Drum Dryer. (2) Approximate 42" diameter x 120" face chrome plated
Used- Double Drum Dryer. (2) Approximate 42" diameter x 120" face chrome plated rolls. Approximate rating 100 psi at 450 degrees F. National Board# 1782-2, Certified by Beloit / Overton Machine Co, Built 1962. Each roll set up for a hydraulic drive. 15HP Hydraulic power pack. Dual knife scraper, top fume hood, edge guides and panel. Mounted on stainless steel end frames.
Stock No.:
53183002Unused Scott TSM42156 Twin-Shaft Continuous Mixer – 5 TPH Industrial Continuous Paddle Blender
Unused Scott TSM42156 Twin-Shaft Continuous Mixer 5 TPH Industrial Continuous Paddle Blender. 42" x 156" shaft dimensions. Designed for 33 lbs/cubic foot. Rated 5 tons/hour. 5 minute retention time. Carbon steel construction. 12" x 24" inlet, 12" x 36" discharge. 120 RPM blender speed. 20 HP shaft mount gear reducer. Driven by a 20 HP, 3/60/230-460V motor. Built 2021.
MFR: Scott Turbon
Stock No.:
53464001Used Double Drum Dryer – 42" x 120" Chrome-Plated Drums with Knife Blade System & Pneumatic Controls
Used- Double Drum Dryer, Chrome plated Drums: 42" diameter x 120" long/ face. Drums rated for 150 psi. With Dryer Frame, knife Blade System, Drum Bearings, Drum Drive System, End Dam System, Steam/Condensate System, Product Removal System, Vapor Removal System, Pneumatic controls. Frame is carbon steel with FDA approved Steel-it paint. Knife Blade System: Two (2) doctor knife holder assemblies with pneumatic knife contact operators. The knife blade holders include Essco Type-KF easy change stainless steel knife blade holders, mounted to the main knife blade holder system. Two (2) pneumatic cylinders maintain each doctor knife in contact and under pressure with the dryer drum. Drums is driven by two (2) independent 7.5 HP motors and gearboxes rated for 1 to 12 RPM. The motors are controlled by two (2) variable frequency drives with digital read-out remote keypads. Motors are high efficiency duty motors. End Dam Assemblies: Two (2) aluminum backed end dams with replaceable Teflon sealing faces. The end dams contact the drum shoulders, under controlled pneumatic pressure. Steam/Condensate System. Product transport is comprised by three (3) product screw conveyors complete with 1 H.P. drive motors and gearboxes: two (2) side screw conveyors and one (1) cross conveyor are provided. The conveyors are fabricated with a 2B finish stainless steel. Transition panels and shields are provided to direct product discharged from the drying drums to the screw conveyors. Vapor Removal System: One (1) stainless steel hinged close-fitting style vapor removal hood with a 7.5 HP exhaust fan. The hood is lifted with air cylinders for easy cleaning. Exhaust fan is controlled by a variable frequency drive. The stainless-steel hood covers the slurry puddle to remove steam vapors and contain splashing in the violently boiling slurry puddle. Exhaust fan can be placed on roof or installed inside. Pneumatic Controls: One (1) pneumatic control system for the control of the following systems: Doct
Stock No.:
54687037Used Devine rotary vacuum dryer with 42 cu. ft. total capacity. Dryer has about 30 cu. ft. working capacity and stainless steel construction including the jacket. It has 36" diameter ribbons, 3.75" d...
Used-Devine rotary vacuum dryer with 42 cu. ft. total capacity. Dryer has about 30 cu. ft. working capacity and stainless steel construction including the jacket. It has 36" diameter ribbons, 3.75" diameter shaft and outboard bearings. Equipped with a 11" center bottom flush valve with a pneumatic actuator. It has (2) 15" manways in top with lids. The necks of the manways are jacketed. This unit is rated at 50 psi @ 300° F. National board # 775. Serial number D-11319-1. Was mounted on a raised platform. (not included). Drive is 7.5 hp 220/440 vac 3 phase. Drive is loose from unit, it was mounted to the stand. Good condition.
MFR: Devine
Stock No.:
54112001Used Thermaline T13 Plate Heat Exchanger – Stainless Steel, 975,672 BTU/Hr
Used- Thermaline Plate Heat Exchanger, Model T13, Stainless Steel. Approximately 42.9 square feet. Flow rate: 44 GPM (Process Side), 145 GPM (Service process). Heat exchanged 975,672 BTU/Hr. Designed temperature 150 psi at 300 degrees F. Gasket material EPDM, CLIP. (33) Plate material 0.6mm, 316 Stainless Steel, CDX. Frame material 304 stainless steel. Serial# 27423-21.
Stock No.:
54112002Stainless Steel Thermaline Plate Heat Exchanger, 44/145 GPM – Used T13 Model
Pre-Owned Thermaline Plate Heat Exchanger, Model T13, Stainless Steel. Approximately 42.9 square feet. Flow rate: 44 GPM (Process Side), 145 GPM (Service process). Heat exchanged 975,672 BTU/Hr. Designed temperature 150 psi at 300 degrees F. Gasket material EPDM, CLIP. (33) Plate material 0.6mm, 316 Stainless Steel, CDX. Frame material 304 stainless steel. Serial# 27423-22.
Stock No.:
54112003Used Thermaline Plate Heat Exchanger, Stainless steel.
Thermaline Model T13 Plate Heat Exchanger - Used, Stainless Steel. Approximately 42.9 square feet. Flow rate: 44 GPM (Process Side), 145 GPM (Service process). Heat exchanged 975,672 BTU/Hr. Designed temperature 150 psi at 300 degrees F. Gasket material EPDM, CLIP. (33) Plate material 0.6mm, 316 Stainless Steel, CDX. Frame material 304 stainless steel. Serial# 27423-23.
Stock No.:
54112005Buy Used Thermaline T13 Plate Heat Exchanger – 33 Plates, 316 SS
Thermaline T13 Plate Heat Exchanger Stainless Steel, Previously Used. Approximately 42.9 square feet. Flow rate: 44 GPM (Process Side), 145 GPM (Service process). Heat exchanged 975,672 BTU/Hr. Designed temperature 150 psi at 300 degrees F. Gasket material EPDM, CLIP. (33) Plate material 0.6mm, 316 Stainless Steel, CDX. Frame material 304 stainless steel. Serial# 27423-25.
Stock No.:
52354002Used Feldmeier 4,200 Gallon Stainless Steel Storage Tank – Vertical, Side Manway
Used- Feldmeier Stainless Steel Approximately 4,200 Gallon Storage Tank, Vertical. Approximately 240" High (straight side) X 72" diameter. Side manway. Last used in Olive Oil operation.
MFR: Feldmeier
