Food and Beverage Equipment

Used Dairy Craft 30,000 Gallon Stainless Steel Insulated Storage Tank | 304 SS | Jacketed | Agitator-Ready | Milk Processing

Used Dairy Craft 30,000 Gallon Stainless Steel Insulated Storage Tank | 304 SS | Jacketed | Agitator-Ready | Milk Processing Dome top, flat sloped bottom. Dimple jacket runs partway up the shell. Insulated. Side bottom hinged manway - doghouse. Provision for a side-mounted agitator in the manway - doghouse. Lifting lugs on the top dome head. Previously used for milk.

MFR: Dairycraft

Used Anhydro Vertical Heat Exchanger / Reboiler – Hastelloy Tubes, 31.8 Sq Ft

Used- Anhydro Vertical Heat Exchanger / Reboiler, Approximate 31.8 Square Feet. Carbon steel shell rated 100psi / FV external at -20 to 600 degrees F. (31) 1" Diameter x 47" long Hastelloy C-276 tubes rated 15 psi internal / 100 psi external at -20 to 600 degrees F. 15,000 Btu/h. Openings: (2) 2", (2) 1". Side lug mounted. Certified by Orbit Industries, National Board# 1025, Serial# 8306-PV-2. No bottom head.

MFR: Anhydro

Industrial Vertical Heat Exchanger – Anhydro, 31.8 Sq Ft, No Bottom Head

Used- Anhydro Vertical Heat Exchanger / Reboiler, Approximate 31.8 Square Feet. Carbon steel shell rated 100psi / FV external at -20 to 600 degrees F. (31) 1" Diameter x 47" long Hastelloy C-276 tubes rated 15 psi internal / 100 psi external at -20 to 600 degrees F. 15,000 Btu/h. Openings: (2) 2", (2) 1". Side lug mounted. Certified by Orbit Industries, National Board# 1024, Serial# 8306-PV-1. No bottom head.

MFR: Anhydro

Used Paul O. Abbe RB-315 Ribbon Blender – 315 Cu Ft Stainless Steel Food Grade Industrial Mixer

Used Paul O. Abbe RB-315 Ribbon Blender 315 Cu Ft Stainless Steel Food Grade Industrial Mixer. 356 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 65.4" wide x 141.8" long x 73.3" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 75 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 20 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 5.5" wide x 27.6" flush air operated plug valve. Discharge housing is approximate 20.5" wide x 36.2" long. Approximately 4" discharge height. Approximate weight 19,580 pounds. Approximate overall dimensions: 87.8" wide x 218.4" long x 100.4" high.

MFR: Paul O Abbe

Cust-O-Fab U Tube 3150 sq ft Shell & Tube Heat Exchanger

Used- Cust-O-Fab U Tube Shell & Tube Heat Exchanger. Approximate 3150 Square Feet. Carbon steel shell rated 1715 psi at 25 to 610 Degrees F. (295) 1" diameter x 20' long SA-213-T11 Chromium-molybdenum steel tubes rated 2184 psi at 30 to 750 degrees F. 1-1/4" tube pitch. Two pass. Openings shell: (3) 8", tubes: 14", 12". Saddle mounted. Serial# 97-202. National Board# 4666. All openings are pipe stubs.

MFR: Cust-O-Fab

Used 3,200 Gallon Stainless Steel Tank – Vertical Dished Vessel with Multiple Po

Used- Stainless Steel Vertical Storage Tank, Approximate 3,200 Gallon Capacity. Approximately 88" diameter x 120" straight side. Dished top, and bottom. Openings Top: (2) 4", (4) 2". 2" Side bottom outlet, 3" bottom & 4" Center Bottom Outlet with approximate 32" discharge height. Side bottom manway with cover. Mounted on (4) stainless steel legs. No mfg tag.

Unused CECO Peerless 324 Gallon 316 Stainless Steel Vertical Oxygen Separator Vessel | ASME Pressure Vessel

Unused CECO Peerless 324 Gallon 316 Stainless Steel Vertical Oxygen Separator Vessel | ASME Pressure Vessel. 42" ID Vertical Oxygen Separator, PMC Part No. VGSP-42I-380SS-001, Drawing No. 9558B-1, is a heavy-wall vertical ASME pressure vessel designed for high-pressure oxygen service and deflagration control applications. Fabricated entirely from 316 stainless steel in accordance with ASME Section VIII Division 1, 2023 Edition, the vessel is rated for full vacuum to 380 PSIG at 194F with a MAWP of 380 PSI at 194F, a MAP of 380 PSI at 100F, and an MDMT of -4F at 380 PSI. The separator is fully ASME U-stamped and National Board registered, requires RT1 radiography, and is hydrostatically tested to 494 PSI for one hour with no PWHT required. Construction includes a 1/2" thick SA-240-316 shell, 1/2" thick 2:1 ellipsoidal heads with 0.4024" minimum formed thickness, heavy-wall Schedule 160 drain and liquid outlet nozzles, reinforced manway assembly, four support legs, lifting lugs, and a davit arm assembly. The vessel includes multiple flanged process and instrumentation connections consisting of 2" inlet, liquid inlet, and outlet nozzles, 3" liquid outlet and drain nozzles, a 2" gas purging connection, 1" DPIT, pressure indicator, vent, and relief valve nozzles, dual 3/4" level gauge connections, dual 1" level controller connections, four 1" level switch connections, and an 18" Class 300 manway. Internal surfaces are oxygen cleaned with neoprene gaskets and flange covers installed for shipment, while the exterior is cleaned, de-scaled, and finished with a sugar blast coating. Estimated vessel weights are approximately 2,412 lbs empty, 5,154 lbs operating, and 5,163 lbs hydrotest weight, with an internal capacity of approximately 324 gallons and a center of gravity located 13.12" from datum. The engineering design package includes ASME VIII Division 1 stress calculations, nozzle reinforcement analysis, hydrostatic test verification, wind and seismic analysis, structural support calculations

MFR: Peerless

Unused CECO Peerless 316 Stainless Steel Oxygen Separator Pressure Vessel | 380 PSI ASME Vessel

Unused CECO Peerless 316 Stainless Steel Oxygen Separator Pressure Vessel | 380 PSI ASME Vessel. 42" ID Vertical Oxygen Separator, PMC Part No. VGSP-42I-380SS-001, Drawing No. 9558B-1, is a heavy-wall vertical ASME pressure vessel designed for high-pressure oxygen service and deflagration control applications. Fabricated entirely from 316 stainless steel in accordance with ASME Section VIII Division 1, 2023 Edition, the vessel is rated for full vacuum to 380 PSIG at 194F with a MAWP of 380 PSI at 194F, a MAP of 380 PSI at 100F, and an MDMT of -4F at 380 PSI. The separator is fully ASME U-stamped and National Board registered, requires RT1 radiography, and is hydrostatically tested to 494 PSI for one hour with no PWHT required. Construction includes a 1/2" thick SA-240-316 shell, 1/2" thick 2:1 ellipsoidal heads with 0.4024" minimum formed thickness, heavy-wall Schedule 160 drain and liquid outlet nozzles, reinforced manway assembly, four support legs, lifting lugs, and a davit arm assembly. The vessel includes multiple flanged process and instrumentation connections consisting of 2" inlet, liquid inlet, and outlet nozzles, 3" liquid outlet and drain nozzles, a 2" gas purging connection, 1" DPIT, pressure indicator, vent, and relief valve nozzles, dual 3/4" level gauge connections, dual 1" level controller connections, four 1" level switch connections, and an 18" Class 300 manway. Internal surfaces are oxygen cleaned with neoprene gaskets and flange covers installed for shipment, while the exterior is cleaned, de-scaled, and finished with a sugar blast coating. Estimated vessel weights are approximately 2,412 lbs empty, 5,154 lbs operating, and 5,163 lbs hydrotest weight, with an internal capacity of approximately 324 gallons and a center of gravity located 13.12" from datum. The engineering design package includes ASME VIII Division 1 stress calculations, nozzle reinforcement analysis, hydrostatic test verification, wind and seismic analysis, structural support calculations

MFR: Peerless

Used 333 Sq Ft Heat Exchanger, Duplex 2205 Construction, 662 PSI Shell Rating, 2023

Used Wuxi Chemical Equipment Horizontal 333 sq. ft. Shell and Tube Heat Exchanger. Duplex 2205 stainless steel tubes rated 288.3 psi at 32 to 330 degrees F, 16' 7'' tube length. Duplex 2205 shell rated 662.3 psi at 32 to 300 degrees F. 15'' Shell diameter. Carbon steel head. National Board #573, Serial #WHA22-087-2-2-C, built 2023.

Used Wuxi Chemical Equipment 333 Sq Ft Shell & Tube Heat Exchanger, Duplex 2205, 2023

Used Wuxi Chemical Equipment 333 Square Foot Horizontal Shell and Tube Heat Exchanger. Duplex 2205 stainless steel tubes rated 288.3 psi at 32 to 330 degrees F, 16' 7'' Tube length. Carbon steel head. 15'' Shell diameter. Duplex 2205 shell rated 662.3 psi at 32 to 300 degrees F. National Board #572, Serial #WHA22-087-2-1-B, built 2023.

Wuxi 333 Sq Ft Shell and Tube Heat Exchanger, Duplex 2205 Tubes & Shell, High Pressure

Used Wuxi Chemical Equipment 333 Square Foot Shell and Tube Heat Exchanger, Horizontal. Duplex 2205 stainless steel tubes rated 288.3 psi at 32 to 330 degrees F, 16' 7'' Tube length. 15'' Shell diameter. Carbon steel head. Duplex 2205 shell rated 662.3 psi at 32 to 300 degrees F. National Board #574, Serial #WHA22-087-2-2-D, built 2023.

Used 34" Cincinnati Milacron Two Roll Sheet Stack – Vertical, 18" x 34" Rolls, Heated

Used- 34" Cincinnati Milacron Two Roll Sheet Stack. 18" Diameter x 34" roll face width rolls, vertical stack orientation, chromed and cored rolls with rotary unions. Silent chain driven with 5 hp, 1750 dc motor thru Koellman gearbox with 18.131:1 ratio, scr motor controller. Pull roll stand with 4" diameter x 34" wide rubber roll driven by 1 hp dc motor with scr controller with idler roll unitized. Temperature control skid, electrically heated with 9 KW Watlow heaters thru shell and tube heat exchanger with pumps and reservoir. Last used with a 2.5" extrusion line.

MFR: Cincinnati Milacron