Cosmetics Equipment
Stock No.:
53267023Alloy Fabricators Inc. approximately 5600 gallon mix tank
Used Alloy Fabricators Inc. approximately 5600 gallon 304 stainless steel vertical mix tank. 90" diameter X 17' high straight side. Internal rated ATMOS @ 200 F. Dished heads. Top fittings: 21" manway, (2) 1.5", (4) 2", (1) 3", and (1) 4". 3" center bottom drain. Has (4) internal baffles. Equipped with dual flight 4-blade agitator driven by Philadelphia model PTERVS-08 S/N 307572, Ratio 38.9-1. Rated 1750 RPM input, 45 RPM output. Powered by 5 HP 3/60/460 volt motor. Lug mounted. Built 1979 OAH 27'
MFR: Alloy Fab
Stock No.:
52283022Used Farr Tenkay Model 2C Cartridge Type Dust Collector – 800 CFM, 1.5 HP Blower
Used- Farr Tenkay Model 2C Cartridge Type Dust Collector. 800 CFM. Rated for 564 square feet filtering area with (2) cartridges measuring 12.75" diameter x 26" long. Includes 6" air inlet, 6" outlet, hinged door, 15" diameter cone bottom discharge. Offered with Cincinnati Fan Model FB/12A Blower, driven by 1.5 HP, 3-phase, 60 Hz, 208-230/460 Volt, 3450 RPM motor. Serial# 9210.
MFR: Farr Co
Stock No.:
10151633Used Mueller 5,700 Gallon Jacketed Pressure Tank | 21,000 Liter Stainless Steel Fermentation Vessel
Used Mueller 5,700 Gallon Jacketed Pressure Tank | 21,000 Liter Stainless Steel Fermentation Vessel, Model F.95" ID x 155" T/T. 268" OAH.Internal 25 psi at 100 degrees F, Jacket rated 100 psi at 100 degrees F.304 stainless steel, vertical, dish top and cone bottom, 16" bottom manway with 3" CBO.Serial # 384634-4, Built 2008.Previous use was brewing beer.
MFR: Mueller Corp
Stock No.:
41174072Used Escher Wyss ZW 2350 Double Drum Dryer | 1,000 kg/hr | Industrial Drum Drying System
Used Escher Wyss Model ZW 2350 industrial double drum dryer with rated processing capacity of 1,000 kg/hr (2,200 lbs/hr). Features two drums measuring 1,500 mm (58.5") diameter x 2,500 mm (97.5") straight side, operating at 26 RPM. Heating pressure rated at 8 bar (120 pounds per square inch) with heating steam pressure of 4 bar (60 pounds per square inch). System includes (1) blower, (1) dust collector, sifter, 5-station sack filling unit, and additional supporting infrastructure. Previously used for processing concentrated skim milk with 45% dry matter content.
MFR: Escher Wyss
Stock No.:
54687141Used MAC model 47-RFHC stainless steel reverse pulse jet dust collector has two (2) 30" long dust collector cartridges with 295 sq. ft. of filter media each. With a 47" diameter, 96" straight side, a...
Used-MAC model 47-RFHC stainless steel reverse pulse jet dust collector has two (2) 30" long dust collector cartridges with 295 sq. ft. of filter media each. With a 47" diameter, 96" straight side, and 70" cone length, this dust collector totals to be about 57" w x 64" l x 174" h. There is a flanged clean air outlet that measures 3.25". Discharge port is 10". Serial no. 28415-012-1.
MFR: MAC
Stock No.:
54687142Used MAC model 47-RFHC stainless steel round reverse pulse jet dust collector holds (2) 30" long dust collecting cartridges with 295 sq. ft. of filter media. There are 3 load cell sensors. With a 47"...
Used-MAC model 47-RFHC stainless steel round reverse pulse jet dust collector holds (2) 30" long dust collecting cartridges with 295 sq. ft. of filter media. There are 3 load cell sensors. With a 47" diameter, 124" straight side, and 70" cone length, this dust collector totals to be about 57" w x 64" l x 232" h. There is a flanged clean air outlet that measures 2". Attached to the discharge port is a MAC multi-duty rotary valve blow-thru. Serial no. 28415-001-1
MFR: MAC
Stock No.:
409352Pre-Owned Vulcan K6ETT Electric Counter Kettle | 6 Gal | 50 PSI
Used Vulcan-Hart Model K6ETT Electric Counter Tilting Kettle, 6 Gallon Capacity. Approximately 11.8" Diameter x 14-1/2" deep. Ellipsoidal bottom. 2/3 Jacketed rated 50psi at -20 to 300 degrees F. Frame mounted. National board# 21596, Serial# 46-3002235, Built 2011. 3/1PH 50/60HZ 8/10KW 208/240V requirements.
MFR: Vulcan
Stock No.:
47890001Lodige FKM600D Plow Mixer
Used- Lodige Model FKM600D batch-type plow mixer with 6 cubic feet working capacity and 10 cubic feet total capacity. 304 stainless steel, non-jacketed mixing chamber approximately 32" diameter x 50" long with 4" diameter shaft, (3) bolt-on plows, (2) bolt-on end scrapers, (2) 18" x 15-1/2" side access doors, and (2) 12" top openings. 9" x 7" bottom outlet with manually operated door and air-purge seals. Serial # 9046. Driven by an approximately 10 hp motor through Falk reducer. Includes control panel with Allen-Bradley PanelView 600 and SLC 5/04 CPU. Mounted on carbon steel stand. Suitable for dry powders, premixes, granular ingredients, spices, nutraceuticals, feed additives, chemical blends, and similar products.
MFR: Lodige
Stock No.:
50556009Used - Paint Media Mill, 8" x 30" Milling Chamber, 6 Gallon, 10 HP Motor
Used- Paint Media Mill. includes 8" diameter X 30" high milling chamber, approximate 6 gallon. Stainless Steel screening section, jacketed chamber. Driven by 10 HP, 220/440 V, 1740 RPM, 3-phase, 60 cycle motor. Previously used at paint processing facility and in working condition when removed from service. No Manufacturers Tag.
MFR: Unknown
Stock No.:
51065016Used Stewart Bolling 6" x 12" Pilot Two Roll Rubber Mixing Mill
Used Stewart Bolling 6" x 12" Pilot Scale Two Roll Mixing Mill With 5 HP Gear Motor. Designed for laboratory, pilot plant and small-batch processing of compatible rubber, plastic and polymer compounds. Features (2) chrome-cored rolls measuring approximately 6" diameter x 12" long, driven by a 5 HP single-speed gear motor with a fixed gear ratio. Equipped with two-point manual roll gap adjustment for controlling material thickness and split end guides for containing material within the working roll area. Safety features include front and rear knee-operated safety mechanisms and an over-the-roll safety cage. Electrical requirements are 220/440 volts, 3-phase, 60 Hz. Serial #2560. Possible applications include rubber compounding, polymer blending, plastic material processing, sheeting, mastication and mixing of compatible natural rubber, synthetic rubber, elastomers, thermoplastic compounds, pigments, fillers and other suitable rubber or polymer formulations.
MFR: Stewart Bolling
