Cosmetics Equipment

Used Charlotte SD-40 Stainless Steel Inline Colloid Mill | 40 HP High Shear Milling System

Used Charlotte SD-40 Stainless Steel Inline Colloid Mill | 40 HP High Shear Milling System. On a common stainless steel base with 40 hp, 230/460 vac, 3 phase, 60 cycle, 3,565 rpm motor. Designed for pumpable slurry products. Rated up to 1,200 gallons per hour, depending on the product being processed. Equipped with 3" OD / 2"ID treaded fittings and an adjustable gap rotor. Partial reduction down to 3-5 microns depending on materials, application and machine configuration. Last used in the food industry. Serial number 4211. This unit includes a motor starter.

MFR: Charlotte

Used Korsch PH 106/DMS Rotary Tablet Press – 6 Station, 40 KN, 32,400 Tablets/Hour

Used- Korsch Rotary Tablet Press, Model PH 106/DMS, 6 station, 40 KN compression pressure, 15 mm max tablet diameter, 15 mm max depth of fill, rated up to 32,400 tablets/hour, machine #1.0037.95.

MFR: Korsch

Used Ross HSM-40 Vacuum Double Helical Mixer Reactor – Stainless, Jacketed, Explosion-Proof

used- Ross HSM-40 Vacuum Double Helical Mixer Reactor, 316 stainless steel. This unit will mix most things that a double planetary mixer will mix, and in many cases, better and faster. Unit has air/oil lift mechanism to raise and lower the drive to allow the removal of the mix tank. Designed for operations under vacuum & a positive pressure of 35 psi @ 350f, jacket maximum allowable working pressure 100 psi @ 350f. Minimum design metal temperature 0f at 100 psi.7.5hp motor. ross metal fabricators Serial# 11801-1, National Board# 463, CRN 15925. stainless steel contact parts. jacketed mix can with provision for thermocouple, insulated with sheathing. explosion proof motor runs on 575 volts, 3 phase, 60 hz. no controls. mixer dimensions for the ross hsm-40: 43" w x 68" l x 91" h lowered position tank id is about 23 and about 27.5 deep. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.

MFR: Ross Industries

Used Ross HDM-40 Gallon Double Planetary Mixer – Vacuum Rated, 316SS, 15 HP (Approx.)

Used- Ross HDM-40 Gallon Double Planetary Mixer. 5 to 40-gallon working capacity. Designed to mix under a full vacuum 29-1/2" HG. An air over oil hydraulic lift system is included to raise and lower the top of the mixer with drives and mixing blades. All product contact parts 316SS with a 150-grit finish and exterior stainless with an 80-grit finish. Driven by a 15 HP (to be confirmed) motor with a mechanical variable speed drive. All carbon steel surfaces are painted with a two component epoxy. Fitted with standard rectangular profile mixing blades.Comes with a control panel suitable for 3 PH / 60HZ /480v. Vacuum hood has a 2" sight port, a light fixture, a vacuum exhaust port and a port with 80 Watts / 120 volts EX-PROOF light. Mixer comes with one mix (not jacketed) can as follows: Made from 316 SS with interior finish 150-grit and exterior finish 80-grit, internally machined for use with a discharge press, designed for vacuum mixing, bottom outlet is a 4" Tri-Clover 316L SS flush plug connection with a 4" flush plug, mounted on casters, push pull handle. Prior use for manufacturing oral care products. Approximate weight of the mixer is 6234 Lbs. Manufactured in 2003.

MFR: Ross Industries

Used Gifford-Wood Model V/P-A AGI-Mixer – 40 Gallon Vacuum Kettle, Homogenizer Mixer, Stainless Steel

Used- Gifford-Wood AGI-Mixer, Model V/P-A, Consisting of: (1) J.C. Pardo & Sons Vacuum Kettle, 40 Gallon, 316 Stainless Steel. Approximate 26" diameter x approximate 26" deep. Lift out clamp on domed top cover, hemispherical bottom. Internal rated 15 psi or full vacuum at 250 degrees F. 304 Stainless steel jacket rated 40 psi at 287 degrees F. Tilt out agitator bridge with inner bar agitator and an anchor style scrapper agitator. (1) Gifford Wood homogenizer mixer, all set up for hydraulic drive. 2" Center bottom outlet. Mounted on (4) legs. Serial# 4402, National Board# 2158. Includes an operator panel, control panel, 0.75hp circulation pump and a Watlow electric heater. Mounted on a common carbon steel base.

MFR: Gifford

Used – Atlas Copco GA30+ Rotary Screw Air Compressor – 40 HP, 210 CFM, 109 PSIG

Used Atlas Copco GA30+ Rotary Screw Air Compressor 40 HP, 210 CFM, 109 PSIG. Approximately 109psig max working pressure, 210 cfm capacity. Driven by a 30kw (40hp) motor. Mounted Control Panel.

MFR: Atlas Copco

Atlas Copco GA30+ Rotary Screw Compressor – 210 CFM, 40 HP Industrial Air System

Atlas Copco GA30+ Rotary Screw Compressor 210 CFM, 40 HP Industrial Air System. Approximately 109psig max working pressure, 210 cfm capacity. Driven by a 30kw (40hp) motor. Mounted Control Panel.

MFR: Atlas Copco

Used Kason K40-1-SS Vibroscreen Circular Sifter | 40" SS Single-Deck | 75 lbs/min | XP Motor | Built 2023

Used Kason K40-1-SS Vibroscreen Circular Sifter | 40" SS Single-Deck | 75 lbs/min | XP Motor | Built 2023. 304 stainless steel construction. Single deck, double separation. 75 lbs/min maximum sift rate. Stainless steel top cover. 3ph/230-460V, 1200 RPM XP motor. Built 2023. Previously used for flour.

MFR: Kason

Unused Admix Rotosolver 250RS175 40 HP High-Shear Mixer

Unused Admix Rotosolver tote-base high-shear mixer, model 250RS175, constructed with 316 stainless steel wetted parts finished to 30 Ra. Unit is equipped with a 40 HP, 1,750 RPM explosion-proof motor rated for 3-phase, 60 Hz, 230/460V electrical service and a nominal shaft speed of 1,750 RPM. Mixer features an approximately 3.15" diameter shaft, 6.89" diameter threaded Rotosolver mix head, and 10.5" diameter 4-blade upper foil secured to the shaft. Unit uses a standard Admix flange mounting arrangement and is configured for mounting on a lift stand. Net weight is approximately 1,090 lb with shipping weight of approximately 1,430 lb. Rated torque is approximately 1,432 in-lb with bending moment of approximately 4,826 in-lb. Explosion-proof motor is UL and CSA approved for Class I, Division 1, Group D or Class II, Division 2, Groups F and G. Possible applications and suitable products include high-shear dispersion, powder wet-out, emulsification, hydration, and mixing of compatible food, beverage, pharmaceutical, cosmetic, chemical, and other liquid-process products.

MFR: Admix

Unused Admix 40 HP Rotosolver High-Shear Mixer

Unused Admix Rotosolver high-shear mixer, model 250RS175, tote-base. Constructed with 316 stainless steel wetted parts finished to 30 Ra. Unit is equipped with a 40 HP, 1,750 RPM explosion-proof motor rated for 3-phase, 60 Hz, 230/460V electrical service and a nominal shaft speed of 1,750 RPM. Mixer features an approximately 3.15" diameter shaft, 6.89" diameter threaded Rotosolver mix head, and 10.5" diameter 4-blade upper foil secured to the shaft. Unit uses a standard Admix flange mounting arrangement and is configured for mounting on a lift stand. Net weight is approximately 1,090 lb with shipping weight of approximately 1,430 lb. Rated torque is approximately 1,432 in-lb with bending moment of approximately 4,826 in-lb. Explosion-proof motor is UL and CSA approved for Class I, Division 1, Group D or Class II, Division 2, Groups F and G. Possible applications and suitable products include high-shear dispersion, powder wet-out, emulsification, hydration, and mixing of compatible food, beverage, pharmaceutical, cosmetic, chemical, and other liquid-process products.

MFR: Admix

Used Ingersoll Rand RS30i-A125 Rotary Screw Air Compressor Package – 40 HP, 184 CFM, 125 PSI

Used Ingersoll Rand RS30i-A125 Rotary Screw Air Compressor Package 40 HP, 184 CFM, 125 PSI. Rated for approximately 184 CFM with a 125 PSI maximum operating pressure. Driven by a 40 HP motor. Package includes an Ingersoll Rand D255NC refrigerated air dryer for moisture removal and improved compressed air quality, along with an air receiver tank to provide air storage, stabilize system pressure, and reduce compressor cycling. Reported 1,772 operating hours. Serial number CBV457593, built 2016. Complete compressed air package suitable for a wide range of industrial applications. Has 0 run hours since last major service was done.

MFR: Ingersoll-Rand

Used Metal Craft TranStore 213 Gallon Tote Bin – 304 Stainless Steel

Used- Metal Craft TranStore Tote Bin, 304 Stainless steel, 213 Gallon. 9400 lb./ 4263 Kg Max. Serial# 75629-5, Built, 2017.