Cannabis Industry Equipment

Used 5 cu.ft. capacity Phauer model AJSP141-6DDPSW twin shaft paddle blender with a side entering chopper. Stainless steel constuction. The twin shaft paddle blender has a 1.5 hp drive on each shaft ...

Used-5 cu.ft. capacity Phauer model AJSP141-6DDPSW twin shaft paddle blender with a side entering chopper. Stainless steel constuction. The twin shaft paddle blender has a 1.5 hp drive on each shaft and the chopper is driven by a 3 hp motor. This unit is equipped with a small dosing tank with spray nozzels. The pipe to the spray nozzels is threaded brass but should be easy to replace with stainless fittings if necessary. The control panel is mounted at one end with a VFD. It is all mounted on a stand with casters for mobility. This unit requires 600 vac 3 ph and includes a 480 to 600 vac step up transformer. Overall dimensions are 80" wide x 52" long x 48" tall. Serial number 99110.

MFR: Phlauer

Used Duriron 630 mm recessed plate filter press. Missing tag for model. Approximately 5 cu.ft. cake capacity. The filter press has (17 plates) gasketed polypropylene recessed plates that measure appr...

Used Duriron 630 mm recessed plate filter press. Missing tag for model. Approximately 5 cu.ft. cake capacity. The filter press has (17 plates) gasketed polypropylene recessed plates that measure approximately 25" wide x 25" tall x 2.25" thick. Center feed, 4 corner return. Plates have 2" diameter outlets in corners and 2.5" diameter center inlet.The filter uses an hydraulic system ram and extended closure. Powered by an Atlas series H heavy-duty hydraulic cylinder, for demanding application up to 3000 psi. Serial number: E02139. Overall 35" x 79" x 104".

MFR: Duriron

Used Brogli-Molto-Mat MMU20 Universal Mixer/Homogenizer – 20L, SS, Jacketed, Vacuum Rated

Used- Brogli-Molto-Mat-Universal Mixer/Homogenizer, Type MMU20. Stainless steel construction, polished on product contact parts. 0.7 cubic foot (20 liter) working capacity. Jacketed and rated for vacuum (-1) Complete with agitator driven via a Reeves gearbox by a 10.5 HP / 7 Kw - 380 volt / 50 cycle / 3 Ph motor. Frame mounted. Previous used in a pharmaceutical application. Serial # 1204010. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.

MFR: Brogli-Molto-Mat-Uni

Used Patterson-Kelley Twin Shell Blender – 50 Cu Ft Working Capacity, Stainless, 5 HP, Bottom Outlet

Used- Patterson Kelley Twin Shell Blender approximately 50 cubic foot working capacity, 83 cubic foot total capacity. Stainless steel mixer contacts with stands and leg extensions. Shell diameter 42". 5 Hp Motor 3/60/208-220-440V with reducer - approximately 14 rpm blender speed. Includes covers, leg extensions and guards. Bottom outlet with valve.

MFR: Patterson Kelley

Industrial 50 Cu. Ft. Stainless Steel Twin Shell Blender – Patterson-Kelley

Used- Patterson-Kelley Twin Shell Blender, 50 Cubic Feet Capacity, 304 Stainless Steel. Rated 55 pounds per cubic foot maximum material density. Standard feed ports with covers, 10" discharge with manual butterfly valve on stainless steel stands. 5 hp, 220/440 volt xp motor drive with brake. Serial # 163723. THIS MACHINE CAN BE ASSEMBLED FOR CUSTOMER AT EXTRA COST.

MFR: Patterson Kelley

Used Patterson-Kelley Twin Shell Blender

Used- Patterson-Kelley (PK) Twin Shell Blender, 50 Cubic Feet Capacity, 304 Stainless Steel. Rated 55 pounds per cubic foot maximum material density. Standard feed ports with covers, 10" discharge with manual butterfly valve on stainless steel stands. 5 hp, 220/440 volt xp motor drive with brake. Serial # 163722. THIS MACHINE CAN BE ASSEMBLED FOR CUSTOMER AT EXTRA COST.

MFR: Patterson Kelley

Used Robinson Air Ring Blower – 50 HP, 5840 CFM | High-Performance Industrial Blower for Airflow & Ventilation Applications

Used- Robinson Air Ring Blower. Approximate 5840 CFM, Static pressure of 20 oz. Driven by a 50 HP, 3/240/480 volt, 3500 rpm motor.

MFR: Robinson

Used 50 Cubic Foot Stainless Steel Double Ribbon Blender with 25 HP Drive

Used 50 Cubic Foot Stainless Steel Double Ribbon Blender with 25 HP Drive. Designed for efficient mixing of dry bulk materials and features a robust stainless steel bowl and ribbon assembly. The unit offers an approximate full capacity of 75 cubic feet and a working capacity of approximately 50 cubic feet, making it suitable for medium- to large-scale blending applications. Inside dimensions of approximately 80" long by 39.5" wide by 41". Equipped with a bottom end discharge system featuring an air-operated discharge valve located approximately 6" from the floor, allowing for efficient and controlled product release. The unit includes a three-piece cover for ease of access and maintenance. Driven by a 25 HP, 3-phase, 60 Hz, 230/460-volt motor, providing reliable performance for continuous industrial operation.

Used GEA Panther1500 Lab Homogenizer – 150 MPa | 50 L/h | Nanoemulsion | High Shear | 2022 | <300 Hrs Use

Used- GEA Panther1500 Process Scale Homogenizer, Type Lab Panther Homogenizer 3006. Maximum pressure 150 MPa; Rated flow of 50 dm3/h; Nanoemulsification production rate (10 mg servings/h) 42,000; 21,700 PSI; 5.5 kW motor power; Includes: Spare parts package; 3A execution; Heat exchanger; IKA T-50 high shear mixer package. Nanoemulsification equipment for manufacturing premium beverages, edibles, and topicals. The GEA pressurizes the fluid and then releases it through a special homogenizing valve. The extreme shearing forces the emulsion experiences during this process causes the droplets to become extraordinarily small, improving its stability and bioavailability. Required Utilities: Lubricating and cooling water of 60 L/h. Reported to have less than 300 hours of use; Serial # 17144; New in 2022. Electrical Requirements: 400 VAC 50 HzAir Requirements: None. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.

Industrial PK Twin Shell V-Blender 50 Cu Ft – Stainless Steel Powder Mixer

Used Patterson-Kelley 50 cu. ft. Stainless Steel Twin Shell V-Blender. 65 lbs/cu. ft. Material density rating. 80 Degree shell. 316 Stainless steel construction. Approximately 18" charging ports, Approximately 10" discharge valve. Driven by approximately 10HP, 3/60/460 volt main drive xp motor. Intensifier bar, driven by 15hp, 3/60/460 volt xp motor. Control panel with Allen Bradley MicroLogix 1400 PLC and A/B PanelView Plus 1000 HMI. Mounted on a 304 stainless steel frame. 188-7/8" Approximate height it drum loader extended. Serial# C438080-2. Ideal for dry, free-flowing solids.

MFR: Patterson Kelley

Used Fryma VME-2400 2400 Liter Vacuum Mixer

Used 2400 Liter working capacity Fryma model VME-2400 vacuum mixer. The tank has an overall height of 101" to the top of lid including legs and 87" to the top with the lid removed. The overall diameter of tank with jacket is 63". The interior dimensions are: 61" diameter, 54" straight side height, 11" dome top, and 11" dish bottom. The working temperatures are 150 C for the interior and the jacket. The interior has a pressure rating of -1/+1 bar and the jacket has a 2.5 bar rating. There are two agitator drives, a 7.5 hp motor that drives a center 3 prop agitator and a scrape agitator through a chain drive and a 50 hp motor that drives a disperser type agitator off to the side of the center shaft. The top has an 8" flanged opening that is clamped shut and 6" glass inspection port with light. The top also has a 2" sanitary, 1.5" sanitary, and (2) 1" threaded fittings. The inside of the unit is polished to pharmaceutical grade. The bottom has a 6" sanitary discharge with a pneumatically operated valve. Fabrication # M10510. Requires 230/ 460 vac 3 phase electrical supply. Previously used for toothpaste. Good Condition.

MFR: Fryma

Used 50 / 10 hp Hockmeyer model HH-L50-10 dual shaft disperser. Stainless steel contact parts. It has one 64" dia. 3 bladed anchor style sweep agitator for the side and bottom (3.25" dia. x 44" long ...

Used-50 / 10 hp Hockmeyer model HH-L50-10 dual shaft disperser. Stainless steel contact parts. It has one 64" dia. 3 bladed anchor style sweep agitator for the side and bottom (3.25" dia. x 44" long shaft) and is driven by a 10 hp variable speed drive. It also has a 17" od high speed dispersion blade (2.9" dia. x 36" long shaft) that is driven by a 50 hp motor. Motors and controls are tagged for hazardous locations. Air over oil lift and includes the air/oil tank. 220 vac 3 ph electric power and air required. The overall dimensions of the disperser are 64" wide x 135" long x 86" tall. Please note: this mixer was designed for a relativly low ceiling height. It is designed so that 20" of the lift post sits through the floor or mezzanine. This unit comes with a 750 gallon open top carbon steel product mix tank that is 70" id x 45.5" tall straight side with a 6" center bottom drain.

MFR: Hockmeyer