Cannabis Industry Equipment

Used Perry Products FTSS-24-1204Z 1,204 Sq Ft 304L Stainless Steel Shell and Tube Heat Exchanger, 2011

Used Perry Products Corporation stainless steel shell-and-tube heat exchanger, size 24-168, serial number B-7509, job number 17450. Rated 1,204 square feet of heat-transfer surface. 304L stainless steel shell, tubes, tube sheets and baffles. Includes (438) tubes, each 3/4-inch OD 0.083-inch wall 14 feet long. Single-pass shell side and six-pass tube side. Shell design pressure 200 PSIG at 350F; tube design pressure 200 PSIG at 500F. Approximately 24-inch OD shell, with 13 feet 11-3/4 inches between tube sheet faces. Includes expansion joint, saddle supports, 8-inch shell-side inlet/outlet connections, and 1/2-inch vent and drain connections. Estimated dry weight 6,000 pounds. Model FTSS-24-1204Z, manufactured in 2011. ASME U-stamped; National Board No. 7500, serial No. B-7509, job No. 17450.

MFR: Perry Products

Used – Southern Heat Exchanger 1220 sq. ft. Vertical Shell & Tube Heat Exchanger

Used- Southern Heat Exchanger 1220 sq. ft. Vertical Shell and Tube Heat Exchanger. 28" diameter x 12'0" f/f. Carbon steel shell, 75fv psi @ 300 deg. F. 316L stainless steel tubes, (388) 1" o.d. x 16 bwg, 75fv @ 300 deg. F. 316L stainless steel heads. With expansion joint. 12'0" tube length. 1.25" tri tube pitch. 16 bwg tube wall. 1 pass shell; 1 pass tubes. NB code. Bem Tema type. 12" and 18" shell nozzles. 2", 4" and 8" tube nozzles. 3 baffles. 35" baffle spacing. 2'4" shell diameter. 17'3" overall length. Built 1989.

MFR: Southern Heat Exchanger

Unused 12,480-Gallon 316L Stainless Steel Reactor with Jacket and Dual Internal Coils

Unused 316L 12480 gallon Stainless Steel Reactor with Jacket and Double Internal Coils. Manufactured by Over Srl. Internal MAWP 87 psi @ 400 degrees F. Halfpipe jacket MAWP 174 psi @ 400F. (1) 1" Internal Coil MAWP 174PSI/FV@400F. (1) 2" Internal Coil rated MAWP 174PSI/FV@400F. Sanitary polished internal and exterior top shell. Dome top and bottom with 2" Center bottom outlet. Top flange and (4) internal baffles with vortex breaker. Does not include motor and agitator. 20" top manway. (4) Lug mounted. 243"OAH x 133"ID. National Board and PED (Double certification). NB #26, Serial #918-1. Built 2025. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.

Used Patterson-Kelley 125 Cu. Ft. Stainless Steel Twin Shell V-Blender – Dual 15 HP Drives with Intensifier Bar

Used Patterson-Kelley 125 Cu. Ft. Stainless Steel Twin Shell V-Blender Dual 15 HP Drives with Intensifier Bar. Rated for a maximum material density of 65 lbs. per cubic foot. Equipped with intensifier bar. Blender driven by a 15 HP motor with intensifier bar driven by an additional 15 HP motor. Unit is mounted on stands. Model: Twin Shell Dry Blender. Serial Number: 229056.

MFR: Patterson Kelley

American Process Systems FPB-125 Fluidized Paddle Blender with Choppers – 125 cu ft, 304 SS, Jacketed (Used)

Used- American Process Systems FPB-125 Fluidized Paddle Blender with Choppers 125 cu ft, 304 SS, Jacketed. Jacket rated 125 PSI @ 350 Degrees F / -20 Degrees F. Main shaft driven by 50 HP, 1775 RPMi / 49 RPMo, 230/460 V. Has (8) choppers, (4) on each side, 15 HP, 3530 RPM, 208-230/460V. Control Panel included. Jacket passed hydrotest.

MFR: American Process Systems

Used Gemini 125 HPSS CNG Gas Compressor – 4 Stage, 300 CFM, 125 HP, Complete System with Cascade, Dryer, Dispensers

Used- Gemini Gas Compressor, Model 125 HPSS, 4 Stage 300 CFM. CNG (Compressed Natural Gas) compressor system includes a four-stage, water-cooled, reciprocating compressor designed for efficient gas compression up to high pressures. U.S. Motors 125 HP, 1760 RPM, 460 Volt motor (S/N X783119) and includes an MK-AJ 24" recapture tank (S/N 9605). It is equipped with an EI C36-0527 cooler (S/N 93483) and a three-cylinder ASME cascade system, each cylinder measuring 20" x 11'6", rated for 5,000 psig and 5,711 cu. ft., with serial numbers 43338, 43339, and 43340. The unit utilizes a Marcum 11 Valve Electro-Pneumatic PMV/SMV priority/sequence panel for flow control. Compression is handled by a Quincy F340-80 air compressor rated at 7.5 HP, 460 Volt, with a discharge aftercooler (S/N 6019514). Drying is managed by a Wilkerson DE3 Twin Tower Heatless Dryer housed in a NEMA 4 enclosure (S/N 4339311). Fuel dispensing is facilitated by two DVCO 2020D dispensers with Hansen nozzles, serial numbers 930034 and 930037.and includes an air-cooled aftercooler, inter-stage separators, and safety relief valves on all stages. The compressor is skid-mounted with an integrated control panel for monitoring and automation, and it is designed for continuous-duty operation. Suitable for vehicle fueling stations or industrial applications, the unit ensures reliable performance with built-in protection systems.

MFR: Gemini

Used Atlas Copco Air Compressor & Dryer System – ZE4-B & FD 1250 VSD

Used 2013 Atlas Copco oil-free rotary screw compressor and VSD dryer package with approximately 5,000 total operating hours, complete with filtration and modern controls. Consists of an Atlas Copco Model ZE4-B Low Pressure Oil-Free Rotary Screw Compressor rated at ~876 CFM, driven by a 125hp 3/60/440-460v 3560rpm air-cooled motor, 33 psig max working pressure, with Elektronikon GraphicPlus HMI and Siemens Sinamics drive (S/N APF185963); an Atlas Copco FD 1250 VSD Refrigerated Air Dryer rated at 2,646.25 CFM, 11.8kW, R404a refrigerant with Elektronikon HMI controls (S/N APF185022); and (2) Atlas Copco DD 1400FF inline air filters with housings (S/N APF185422/423). Oil-free screw technology with refrigerated drying and inline filtration makes this package well-suited to clean-air applications in pharma, food and beverage, electronics, and any process where oil carryover is unacceptable. Turnkey, ready-to-integrate compressed-air solution rather than a bare machine. System reported in excellent working condition; documentation available, photos and inspection recommended.

MFR: Atlas Copco

Used Chicago Blower centrifugal fan blower. Size 365. Up to 36,000 acfm @ 15.5" wg SP. Serial number 308228. Inlet 40" diameter with cone to 54" diameter. Outlet 40" x 28"". Overall size 68" wide x 1...

Used Chicago Blower centrifugal fan blower. Size 365. Up to 36,000 acfm @ 15.5" wg SP. Serial number 308228. Inlet 40" diameter with cone to 54" diameter. Outlet 40" x 28"". Overall size 68" wide x 100" tall x 122" long. Motor 125 HP. Electrical power 460 vac 3 phase.

MFR: Chicago Blower

Used Chicago Blower centrifugal fan blower. Size 365. Up to 36,000 acfm @ 15.5" wg SP. Serial number 308228. Inlet 40" diameter with cone to 54" diameter. Outlet 40" x 28"". Overall size 68" wide x 9...

Used Chicago Blower centrifugal fan blower. Size 365. Up to 36,000 acfm @ 15.5" wg SP. Serial number 308228. Inlet 40" diameter with cone to 54" diameter. Outlet 40" x 28"". Overall size 68" wide x 92" tall x 122" long. Motor 125 HP. Electrical power 460 vac 3 phase.

MFR: Chicago Blower

Used Clarage Fan Company type 0, size 325 stainless steel centrifugal fan. It is rated for 8,500 cfm @ 37" static pressure. The blower has a 24" diameter inlet and a 12" wide x 18.5" long rectangular...

Used-Clarage Fan Company type 0, size 325 stainless steel centrifugal fan. It is rated for 8,500 cfm @ 37" static pressure. The blower has a 24" diameter inlet and a 12" wide x 18.5" long rectangular discharge. It has a 10" x 15" access door in each end (see pictures) It is belt driven by a 125 hp 230/460 vac 3 ph motor that is tagged for hazardous locations. The motor was previously mounted on a concrete pillar. Buyer will have to make provision for mounting the motor. Overall dimensions of the blower are 82" across x 55.25" deep x 76" tall. Good condition.

MFR: Clarage

Used Clarage Fan Company type 0, size 325 stainless steel centrifugal fan. It is rated for 8,500 cfm @ 37" static pressure. The blower has a 24" diameter inlet and a 12" wide x 19" long rectangular d...

Used-Clarage Fan Company type 0, size 325 stainless steel centrifugal fan. It is rated for 8,500 cfm @ 37" static pressure. The blower has a 24" diameter inlet and a 12" wide x 19" long rectangular discharge. It has a 10" x 15" access door in each end and a 10" x 15" cleanout under the intake (see pictures). It is belt driven by a 125 hp 230/460 vac 3 ph motor that is tagged for hazardous locations. The motor was previously mounted on a concrete pillar. Buyer will have to make provision for mounting the motor. Overall dimensions of the blower are 81" across x 55.25" deep x 76" tall. Good condition.

MFR: Clarage

Used 1,250 Gallon 304 Stainless Steel Vertical Mix Tank – Dual Turbine Agitator,

Used 1,250 Gallon 304 Stainless Steel Vertical Mix Tank. Approximate 98" diameter x 42" straight side. Flat top, slight dish bottom. Top agitator bridge with a Chemineer 2-tier 3-turbine agitator. Driven by a 1hp, 3/60/230/460 volt, 1160rpm gear motor. Openings Top: (2) 12" manways, 1-1/2". Approximately 3" center bottom outlet. (4) internal mounted baffles. Mounted on (4) Stainless Steel Legs. No Manufacturers Tag.