Adhesive and Sealant Equipment

Used CAT Solar Turbines Centaur 40 Natural Gas Turbine Power Package – Approx. 3.7 MW

Used- Cat Solar Turbines Turbine Package. Approximate output of 3.5 MW per unit/Approximately 7 MW total. Natural gas powered. Consists of (2) Solar Turbine Model Centaur 40; Exhaust systems; Gas-fired burner systems; Associated electrical infrastructure. Configured for venting or integration with steam generation systems. Serial# HG85083 and HG85093. Reported approximate 30,000 operating hours.

MFR: Solar

Used ACS Atlantes Chemical Systems 24" x 24" Plate & Frame Filter Press – 21 Polypropylene Plates with Enerpac Hydraulic Closure

Used ACS (Atlantes Chemical Systems) Plate and Frame Filter Press. (21) 24" x 24" Polypropylene Filter Plates. Approximately 3" diameter center hole, (4) 1-1/4" corner holes. Unit is mounted on a heavy-duty carbon steel frame and includes an Enerpac hydraulic plate-closing system, lower cake-discharge hopper with 42" discharge height.

MFR: ACS

Used Jenbacher JGS-416 1.127 MW Natural Gas Generator – 4,160V Enclosed Power Package with Switchgear

Used- Jenbacher Natural Gas Generator Package, Model JGS-416. Rated 1.127 MW. Approximately 96% generator efficiency. Includes fully enclosed transportable weatherproof building and switchgear. 1800 RPM. 1573 bhp motor. 60hz/4160V. Built 2011. Reported 67,000 hours.

MFR: Jenbacher

Used Hemraj PSD 02 Stainless Steel Spray Dryer – 22 Lb/Hr Water Evaporation, Two-Fluid Nozzle Atomization

Used Hemraj PSD 02 Stainless Steel Spray Dryer 22 Lb/Hr Water Evaporation, Two-Fluid Nozzle Atomization. 316 stainless steel contact parts. 304 stainless steel non-contact parts. 36" diameter x 69" straight side chamber size. Two-fluid compressed air nozzle atomizer 10 kg/hour (approximately 22 lbs/hour) water evaporation capacity. 14.5 kg/hour (approximately 32 lbs/hour) feed rate w/ 30% dry solids feed. 4.5 kg/hour (approximately 10 lbs/hour) powder rate. Ambient- 260 degrees C (500 degrees F) inlet temperature. 95-100 degrees C (203-212 degrees F) outlet temperature. 30-40 degrees C (86-104 degrees F) ambient temperature. 760mm Hg atmospheric pressure. 50% relative humidity. Blown down" powder collection method. Electric air heater heat source. 3/50/440V electric motor. Built 2014. Previously used for organic biopesticides.

Used 2020 Stokes 900-513R Custom 23-Station Rotary Tablet Press – Die-Twisting Ejection, Under 2 Pressing Hours

Used- 2020 Stokes Custom Rotary Tablet Press, Model 900-513R with 23-station turret and less than 2 hours of actual pressing operation.. This machine features a custom die-twisting design that rotates the dies to help break sticking during tablet ejection, providing a specialized solution for products prone to sticking during the ejection process. Equipped with 23-station rotary turret, product hopper and feed system, compression and adjustment controls, machine guarding, and floor-mounted drive assembly. Electrical requirements are 480 volts, 60 Hz, 3 phase, 10 amps. Serial # 032036, Manufactured in 2020 and showing exceptionally low pressing use, this custom Stokes press combines the established 900-513 platform with a specialized 23-station turret and die-twisting ejection arrangement. Possible applications include pharmaceutical, nutraceutical, vitamin, supplement, confectionery, chemical, and specialty tablet production, particularly products where sticking during tablet ejection is a concern.

MFR: Stokes

Used 2018 BUCHI B-290 Mini Spray Dryer with B-295 Inert Loop – Laboratory Spray Drying System for Aqueous & Organic Solvent Applications

Used- Buchi Mini Spray Dryer, Model B-290. With glass drying chamber and atomizer. Includes Buchi B-295 Inert Loop for spray drying with organic solvents under an inert gas atmosphere, with oxygen and pressure control to prevent explosive conditions. B-295 features cooling capacity of 800 W at -10 C and minimum outlet temperature of -20 C. Built 2018.

MFR: Buchi

Used American Isostatic Presses AIP3-12-60CP Research Cold Isostatic Press – 60,000 PSI, 3" x 12" Working Chamber

Used- American Isostatic Presses (AIP) Research Cold Isostatic Press, Model AIP3-12-60CP. Rated for 60,000 psi maximum working pressure with a 3" diameter x 12" long working chamber. Equipped with a PV66-03-12CP pressure vessel, pin-top closure, and Haskel pump, rated for 60,000 PSI. 15-40 degrees C temperature limits. Astra controls with Bourdon tube type gauge, and Omron timer. 50/60hz, 110V.

Unused 304 Stainless Steel Centrifugal Spray Drying System

Unused 304 Stainless Steel Spray Dryer. 15 liters/hour maximum evaporation rate. Gas powered. Centrifugal spraying nozzle. Mechanical transmission. 150-200 degrees C (302-392 degrees F) (auto controlled) inlet temperature. 80-100 degrees C (176-212 degrees F) outlet temperature. 2,500 RPM atomizer speed. 60mm spray disk diameter. = 95% powder recovery. 80mm Aluminum Silicate insulating layer. 3-5% finished product moisture content. Mounted on frame with dust collector. Stainless steel Dust collector: 640mm diameter x 1,000mm straight side length x 300mm vertical body length. 108mm bottom outlet diameter. (3) electromagnetic valves. (10) cloth bags.

Used Carrier Vibrating Equipment Model FTD/AD2460S Stainless Steel Vibratory Fluid Bed Dryer System

Used Carrier Vibrating Equipment Model FTD/AD2460S stainless steel vibratory fluid bed dryer, Serial #27191, built 2009. System includes control panel, Stelter & Brinck direct-fired gas air heater, flame control panel, blower, rotary valve, additional blower, MAC cyclone, rotary valve, additional blower and sock filter. Possible applications include continuous drying of suitable powders, granules, crystalline solids, filter cakes, fibrous materials and other bulk products requiring controlled fluid bed drying.

MFR: Carrier

Used Carrier Vibrating Equipment Model FTDII/AD2490S Stainless Steel Vibratory Fluid Bed Dryer System

Used Carrier Vibrating Equipment Model FTDII/AD2490S stainless steel vibratory fluid bed dryer, Serial #27748, built 2012. System includes an inclined discharge screw conveyor approximately 12" diameter x 12' long with magnet, Kongslide blower, control panel, Stelter & Brinck direct-fired gas air heater, flame control panel, MAC cyclone, rotary valve, assorted blowers and sock filter. Possible applications include continuous drying and cooling of suitable powders, granules, crystalline solids, filter cakes, fibrous materials and other bulk products.

MFR: Carrier

Used Witte Model 42 x 12' PE Pellet Fluid Bed Cooler / Dryer – 45" x 12'10" Shaker Deck with Natural Gas Heat

Used Witte Model 42 x 12' PE Pellet Fluid Bed Cooler / Dryer 45" x 12'10" Shaker Deck with Natural Gas Heat, Serial Number 5263. Used Witte fluid bed cooler, 45" wide x 12'10" long, set up for heat. Equipped with Siemens 3 HP shaker motor, Power Flame FD300 natural gas burner with RCP FD300 control box, induction blower, temperature regulators, shaker deck with tension springs, removable hood with safety chain, fabricated induction ducting and cylindrical exhaust hood. Screen in great condition with no bends or clogs; shaker, motor, burner, blower and temperature controls function as intended. Shaker fluid changed January 2026. Stand measures 12'2" long x 5' wide x 8'4" high, 10'5" high to safety hoist. Includes approximately 12' wide x 14' long induction ducting and 28' long x 12" wide x 31" deep outlet ducting. Previously used for PE pellets and suitable for heating, drying, conditioning or cooling compatible plastic pellets and free-flowing granular products.

MFR: Witte

Used 2008 Applied Chemical Technologies 10 Sq. Ft. Vibrating Fluid Bed Dryer – 30 HP Blower & Power Flame Burner

Used 2008 Applied Chemical Technologies 10 Sq. Ft. Vibrating Fluid Bed Dryer 30 HP Blower & Power Flame Burner, set up for heat with stainless steel stand, body, induction hood and exhaust hood. Equipped with Reliance Electric 30 HP blower motor and Power Flame 4x Micro Burn burner. Screener deck is in good condition with no unintended holes. Unit was operated in August 2026 and includes burner spare parts and an additional non-functioning burner. Assembly is arranged on four skids for burner assembly, blower fan and coil, induction unit and fluid bed dryer, with exhaust duct requiring an additional skid. Dryer with hood measures 9'6" high x 8' long x 3'4" wide; dryer only measures 34" wide x 8' long x 7' high; overall length with induction ducting is 19'10". Built 2008. Suitable for heated fluid bed drying and processing of compatible free-flowing granular and particulate products.

MFR: Applied Chemical Technology