Your Files Are Being Processed
Please Wait
Contact Information
Phone: 630-350-2200
Toll Free: 1-800-49-AARON
Email: websales@aaronequipment.com
Used Davis Standard Co-Extrusion 78" Wide Sheet Line. Consisting of the following: Davis Standard 6" Extruder Model # 60IN60TPIH, Serial # V8036, SO # 61167, Built 5/98. 30:1 L/D Ratio, top vented barrel. Electrically heated, water cooled. Unit direct connected to 400 hp DC motor and Drive Gearbox rated to 645 hp, 1.5 service factor, 13.4:1 ratio, screw rpm is 100. Unit included a unitized control panel having 6 barrel zones, 15 downstream zones, all are Eurotherm digital controllers, GE Fanuc 90-30 PLC, Magnetek GPD 5/5 drive, GE DV-300 Drive. Extek 6" hydraulically operated slide plate screen changer, Model HSC-60, Serial # H60320, requires power pack. LCI Corp melt pump, Model ES 90/90, Serial # 1985. Wintek Corp/DVT vacuum system, with Model DV0100B-KA3 pump, driven by a 7-1/2 hp motor. Die block. Co Extruder Davis Standard 3.5" Extruder Model # MV-35IN35, Serial # V8039, SO # 61167, Built 5/98. 30:1 L/D ratio side vented barrel. Electrically heated and water cooled. Unit Direct connected 150 hp DC Motor thru Gearbox having 17.39:1 ratio, 158 hp capacity, 1.254 service factor, 100 rpm screw speed. Unitized control panel with Eurotherm temperature controllers (5) barrel zones, (6) downstream zones, GE Fanuc 90-30 PLC, Yasakawa Varispeed F7 VFD, GE DV-300 Drive. Extek 3.5" hydraulically operated slide plate screen changer, Model HSC-35, Serial # H35338, requires power pack. LCI Corp melt pump, Model ES 56/56, Serial # 1995. Wintek Corp/DVT vacuum system, with Model DV0100B-KA3 pump, driven by a 7-1/2 hp motor. Both extruder connect thru EDI Ultraflow Co-EX die block to EDI Ultraflex HRC-100 78" wide Restrictor bar sheet die and manual deckling option, mass 3676 pounds, Serial # 98-19772 with die cart. Davis Standard 24" x 78" three roll chrome downstack operation. Hydraulic roll adjustment. Rolls are gear driven by a common 7.5 hp, 3/60/460 volt, 1762/3525 rpm gearmotor, 200 to 1 ratio. Eurotherm temperature controllers for rolls. Water cooled rolls with DS water system consisting of (3) centrifugal 10 hp pumps, (3) heat exchanger with unitized control with (2) Yasakawa GPD515/65 drive for rollstand and pull roll, Magnetek GPD333 drive for sheet stack locomotive, GE Fanuc 90-30 PLC. Miller fluid power hydraulic power unit. Conveying section including a NDC Technologies Model T2-65 scanning device, Serial # 4752. Davis Standard Haul Off rubber pull roll stand, (2) approximate 8" diameter x 78" wide rubber rolls, driven by a 7.5 hp gearmotor, 143.47 to 1 ratio Seria l# V-8056, S.O.# 61167, built 5/98. Vulcan sheet stacker, (2) 36" wide x 72" long conveyor belts driven by 1 hp motor, has Emerson FX-490 servo drive, GE fanuc 90-30 PLC. Includes power take off table.
Used Davis Standard Co-Extrusion 78" Wide Sheet Line. Consisting of the following: Davis Standard 6" Extruder Model # 60IN60TPIH, Serial # V8036, SO # 61167, Built 5/98. 30:1 L/D Ratio, top vented barrel. Electrically heated, water cooled. Unit direct connected to 400 hp DC motor and Drive Gearbox rated to 645 hp, 1.5 service factor, 13.4:1 ratio, screw rpm is 100. Unit included a unitized control panel having 6 barrel zones, 15 downstream zones, all are Eurotherm digital controllers, GE Fanuc 90-30 PLC, Magnetek GPD 5/5 drive, GE DV-300 Drive. Extek 6" hydraulically operated slide plate screen changer, Model HSC-60, Serial # H60320, requires power pack. LCI Corp melt pump, Model ES 90/90, Serial # 1985. Wintek Corp/DVT vacuum system, with Model DV0100B-KA3 pump, driven by a 7-1/2 hp motor. Die block. Co Extruder Davis Standard 3.5" Extruder Model # MV-35IN35, Serial # V8039, SO # 61167, Built 5/98. 30:1 L/D ratio side vented barrel. Electrically heated and water cooled. Unit Direct connected 150 hp DC Motor thru Gearbox having 17.39:1 ratio, 158 hp capacity, 1.254 service factor, 100 rpm screw speed. Unitized control panel with Eurotherm temperature controllers (5) barrel zones, (6) downstream zones, GE Fanuc 90-30 PLC, Yasakawa Varispeed F7 VFD, GE DV-300 Drive. Extek 3.5" hydraulically operated slide plate screen changer, Model HSC-35, Serial # H35338, requires power pack. LCI Corp melt pump, Model ES 56/56, Serial # 1995. Wintek Corp/DVT vacuum system, with Model DV0100B-KA3 pump, driven by a 7-1/2 hp motor. Both extruder connect thru EDI Ultraflow Co-EX die block to EDI Ultraflex HRC-100 78" wide Restrictor bar sheet die and manual deckling option, mass 3676 pounds, Serial # 98-19772 with die cart. Davis Standard 24" x 78" three roll chrome downstack operation. Hydraulic roll adjustment. Rolls are gear driven by a common 7.5 hp, 3/60/460 volt, 1762/3525 rpm gearmotor, 200 to 1 ratio. Eurotherm temperature controllers for rolls. Water cooled rolls with DS water system consisting of (3) centrifugal 10 hp pumps, (3) heat exchanger with unitized control with (2) Yasakawa GPD515/65 drive for rollstand and pull roll, Magnetek GPD333 drive for sheet stack locomotive, GE Fanuc 90-30 PLC. Miller fluid power hydraulic power unit. Conveying section including a NDC Technologies Model T2-65 scanning device, Serial # 4752. Davis Standard Haul Off rubber pull roll stand, (2) approximate 8" diameter x 78" wide rubber rolls, driven by a 7.5 hp gearmotor, 143.47 to 1 ratio Seria l# V-8056, S.O.# 61167, built 5/98. Vulcan sheet stacker, (2) 36" wide x 72" long conveyor belts driven by 1 hp motor, has Emerson FX-490 servo drive, GE fanuc 90-30 PLC. Includes power take off table.
We pay "Top Dollar" for your idle process equipment! Fill out our form and our buying team will get back to you.
SELL YOUR EQUIPMENTView our entire process equipment inventory online or visit our location for an equipment inspection.
View Inventory