Used Sheet Extrusion Lines

Stock# 10755102

Used-Randcastle Model RPSTCO-8X2 Three Roll Sheet Stack. Three 8" wide x 2" diameter chrome rolls, 8" x 2" pull rolls - one rubber and one chrome. All rolls pneumatically operated, 6.5" x 3" winder, powered by a 1/2 hp DC motor with Bronco II controller, all mounted on unitized base.

Stock# 47965002

Used- Davis Standard 3- Roll Sheet Stack, 30" Wide, Model F8082, SO#98080. Includes 10' Long idler conveyor, pull roll stand, and shear. Hydraulic pump for cylinders on stack and Mokon oil unit. Includes (1) spare chrome roll, (2) spare silcon rolls and (3) spare eteched hair cell rolls.

Stock# 49502001

Used- Commodore Technologies Ltd. (Bloomfield, NY) PSP foam sheet extrusion line with an output capacity 1320 lbs./hr. (600 kg/hr.) consisting of: (1) Davis Standard single screw extruder, 5" (130 mm) dia. 34:1 L/D. Electrically heated. Air cooled. Gearbox driven by a 277.5 HP/185 Kw AC motor. 1) Davis Standard single screw extruder, 6.4" (165 mm) dia. 34:1 L/D. Electrically heated. Air cooled. Gearbox driven by a 165 HP/110 Kw AC motor. (2) Screen changers. (1) Ring-die, calibrator, pull machine, (2) Winding machines 39" (1200 mm) dia x 36" (1102 mm) st. side. Max roll weight 996.6 lbs. (453 kgs) allowed. Complete with (1) tensiometer dosing system. (1) LEWA gas dosing system, (1) chilling/Cooling system, (2) thermo controllers, electrical control cabinets and further infrastructure. New year 2013.

Stock# 46471001

Used- Davis Standard Sheet Extrusion Line. Consisting of one (1) used 7.5 hp Conair vacuum loader; One (1) used Walton Stout four material volumetric blender; One (1) used Davis Standard Model 45IN45 single screw extruder Serial # K9443, SO# 02310, year 1989, 13.7 gearbox ratio, 250 hp DC motor, 4.5" diameter screw, 34:1 L/D ratio, electrically heated, water cooled, vented and plugged barrel, 7 barrel zones, HES 301 controls, One (1) used Xaloy EH-45 screen changer Serial # EH45788 with 2 hp Beringer hydraulic pump, One (1) used Davis Standard / Marshal & Williams three roll sheet stack 36" wide x 16" diameter smooth polished chromed cored rolls, silent chain driven, hydraulically actuated closure with integrally mounted pull roll stand, Four (4) Advantage Sentra temperature control units.

Stock# 50221001

Used- Battenfeld Gloucester 36” Wide Inclined Sheet Line Consisting Of: (1) Battenfeld Gloucester 3-1/2” single screw extruder, model 233-001, Serial# 233-33310-01, Built 1990. 30 to 1 L/D Ratio, electrically heated, water cooled side vented 5 zone barrel with pump, tank & heat exchanger. Water cooled feed throat with a Maguire (4) compartment weigh scale blender, model WSB940, serial# B122213-38, built 2012. Approximate 60” centerline height. Extruder driven by a 150hp, 640 volt DC motor thru a Battenfeld Gloucester model 35250 gearbox, ratio 15.46 to 1. Control panel with an operator screen, and Powertec 2000A drive. (1) Gneub 3-1/2” hydraulic screen changer, model MS-90, serial# 1190853, includes a power pack. (1) Maag Extrex type 56/56 gear pump, serial# 8330-63034-12, driven by an approximate 10hp DC motor with reducer, (1) 24” wide die with 45 degree down angle adapter, (1) Battenfeld Gloucester inclined style 3 roll sheet stack, serial# 33310-13, built 1990. (2) 16” Diameter x 36” wide chrome plated cored rolls, (1) 16: diameter x 36” wide matte finish cored roll, each roll individually driven by a 1hp DC gear motors with an operator panel and control panel with Powertec drives and (3) temperature control units. (1) Edge trimmer with approximate 14’ long cooling conveyor. (1) Battenfeld Gloucester 36” wide pull roll stand, driven by a 3hp motor with reducer, (1) Dekker DV0100D-MA3-SGL vacuum pump, serial# 30413, driven by a 5.5kw motor. Incluces (2) spare chrome rolls, (2) spare rubber rolls and (2) damaged chill rolls. Still installed as operated until approximately 7/1/2019.

Stock# 49869001

Used- Welex Sheet Line. Consisting of: (1) 4-1/2'' 32:1 Non Vented Extruder, Water Cooled with Control Panel, 250 hp D.C. Motor and 54'' Centerline. (1) 15 HP Dynisco Melt Pump. (1) 4.5 '' Berringer Screen Changer with Power Pak. (1) Davis Standard 2.5'' 30:1 Water Cooled Extruder Mfg. in1998 with Berringer Hydraulic Screen Changer and Power Pack, 60 HP Drive and Controls. (1) COEX Feed Block, New in 1998. (1) 41'' EDI Flex Lip Die. (1) 41'' Welex 3 Roll Sheet Stack with Pull Rolls and Temperature Controls, Rolls are 24'' Diameter. (2) Cart Style Torque Motor Rewinders with 5 Carts.

Stock# 44894001

Used- Egan Three Roll Horizontal Sheet Stack. (3) 42" wide x 18" diameter chrome plated cored rolls. Hydraulically adjustable with power pack. Each roll is driven by a 2hp, 150 volt, 3500 rpm DC motor with reducer, ratio 250 to 1. Serial# FO-0825852.

Stock# 10755098

Used-Processing Technologies Inc Model 5024 3 Roll Down Stack, manufactured 2/2000. 24" Diameter x 50" wide lower 2 chrome rolls, upper roll is 12" x 50", all chrome rolls cored for cooling, rolls are hydraulically operated and powered by a 7.5 hp DC motor via silent chain drive. Control Techniques Mentor II DC drives for stack and pull roll station, pull rolls pneumatic operation and powered by a 5 hp DC motor. Cooling via 3 x 10 hp pumps into heat exchangers.

Stock# 43833002

Used- 54" Wide Gloucester Sheet Line. Consisting of the following: 3.5" Gloucester extruder, 32:1 l/d, electrically heated, water cooled, 150 hp DC motor with SCR controller, control panel with 5 barrels, 1 adapter, 1 screen changer, 1 melt pump, 7 die zones, 3.5" screen changer, extruder Serial # 33252-01, 40" EDI sheet die, Gloucester 54" wide x 16" diameter three roll vertical sheet stack, cored rolls with rotary unions with cooling conveyor, Gloucester 54" wide pull roll stand with rubber pull rolls, Gloucester 3 position winder, Model 115, Serial # 33121-01. Elecectric: 3/60/460V.

Stock# 49624002

Used- Welex 3 Roll Sheet Stack, Model 18x18x18x72, (3) 18" x 72", 5HP Individually Driven Chrome Rolls, Year 2000, includes Controls, 480 Volt, 3 phase, 60 Hz. 214 Amps, Fixed middle Roll, Adjustable Top and Bottom Rolls. Top Roll Set Back to allow 45 Degree Entry Between The Downstack operation.

Stock# 50099001

Used- Coperion Sheet Extrusion Line. Includes the following: Ktron Feeding system, Model k2-ML-S100, KCM-5 & KCM-4 feeders; KCM Touchscreen Controller; Coperion Extruder Type ZSK-92 MC18 Model 64055440 Serial 20524240; 92mm screw diameter co rotating design 48:1 L/D ratio. Gearbox: Ratio 1:5.473, Maximum Torque 7500 Nm, Maximum motor Speed 1800 RPM, Maximum Screw Speed 328 RPM, Maximum Allowable Horsepower 690; Extruder Driven by Baldor Electric 800 HP Motor Spec A50-1642-6340, S/N K1410100011m 1789 RPM, 885 Amps, 460 Volt, 60 Hz; Allen Bradley PowerFlex 755 Variable Speed Controller; Extruder has 12 Barrel Sections 360mm each, (1 Feed Barrel, 3 Vent Barrels, 8 Closed Barrels), Shaft Centerline Height 76mm; Coperion ZS-B 92 Side Feeder S/N 205242241, Year 2015, Driven by Stober 15Kw Electric motor 480V 60 Hz, 25 Amps, 1780 RPM. Extruder is Electrically Heated, Water Cooled; Maag Dual Piston Screen Changer Back Flushing Type; 7.8" Screens, Year 2015, including Hydraulic Unit; Maag Gear Pump Model EX-5 GP 110 SN 50138652-20, Capacity 4000 LBS/Hr; Allied (ADI) 72" Flex Lip Sheet Die job# AD2763; Davis Standard 3-Up Sheet Stack, Bottom Roll is 18" Diameter x 72" Wide Top Rolls are 36" Diameter x 72" Wide. Rolls are individually driven by AC motors, With Touchscreen Controller and Cooling System; Scantech X-Ray Gauge Frame LF1-2000 S/N 001REPL.0001-001DASD.0021-000, Year 11/2014. Dual Rubber Pull Roll Stand, Approximate 17' Long cooling section with Dual Edge Trim Section and Vacuum system for regrind; Winding Accumulation tower; (4) Turret Shuttle type Winder; Includes Unicarriers Turret Shuttle. All Controls are Allen Bradley PLC. Mfg. 2014.

Stock# 50011001

Used- Davis Standard Co-Extrusion 78" Wide Sheet Line. Consisting of the following: Davis Standard 6" Extruder Model # 60IN60TPIH, Serial # V8036, SO # 61167, Built 5/98. 30:1 L/D Ratio, top vented barrel. Electrically heated, water cooled. Unit direct connected to 400 hp DC motor and Drive Gearbox rated to 645 hp, 1.5 service factor, 13.4:1 ratio, screw rpm is 100. Unit included a unitized control panel having 6 barrel zones, 15 downstream zones, all are Eurotherm digital controllers, GE Fanuc 90-30 PLC, Magnetek GPD 5/5 drive, GE DV-300 Drive. Extek 6" hydraulically operated slide plate screen changer, Model HSC-60, Serial # H60320, requires power pack. LCI Corp melt pump, Model ES 90/90, Serial # 1985. Wintek Corp/DVT vacuum system, with Model DV0100B-KA3 pump, driven by a 7-1/2 hp motor. Die block. Co Extruder Davis Standard 3.5" Extruder Model # MV-35IN35, Serial # V8039, SO # 61167, Built 5/98. 30:1 L/D ratio side vented barrel. Electrically heated and water cooled. Unit Direct connected 150 hp DC Motor thru Gearbox having 17.39:1 ratio, 158 hp capacity, 1.254 service factor, 100 rpm screw speed. Unitized control panel with Eurotherm temperature controllers (5) barrel zones, (6) downstream zones, GE Fanuc 90-30 PLC, Yasakawa Varispeed F7 VFD, GE DV-300 Drive. Extek 3.5" hydraulically operated slide plate screen changer, Model HSC-35, Serial # H35338, requires power pack. LCI Corp melt pump, Model ES 56/56, Serial # 1995. Wintek Corp/DVT vacuum system, with Model DV0100B-KA3 pump, driven by a 7-1/2 hp motor. Both extruder connect thru EDI Ultraflow Co-EX die block to EDI Ultraflex HRC-100 78" wide Restrictor bar sheet die and manual deckling option, mass 3676 pounds, Serial # 98-19772 with die cart. Davis Standard 24" x 78" three roll chrome downstack operation. Hydraulic roll adjustment. Rolls are driven by a common 7.5 hp, 3/60/460 volt, 1762/3525 rpm gearmotor, 200 to 1 ratio. Eurotherm temperature controllers for rolls. Water cooled rolls with DS water system consisting of (3) centrifugal 10 hp pumps, (3) heat exchanger with unitized control with (2) Yasakawa GPD515/65 drive for rollstand and pull roll, Magnetek GPD333 drive for sheet stack locomotive, GE Fanuc 90-30 PLC. Miller fluid power hydraulic power unit. Conveying section including a NDC Technologies Model T2-65 scanning device, Serial # 4752. Davis Standard Haul Off rubber pull roll stand, (2) approximate 8" diameter x 78" wide rubber rolls, driven by a 7.5 hp gearmotor, 143.47 to 1 ratio Seria l# V-8056, S.O.# 61167, built 5/98. Davis Standard (Famco) shear, Model P-1496WG, .25 plastic capacity, driven by 5 hp motor, Serial # S-05986361. Vulcan sheet stacker, (2) 36" wide x 72" long conveyor belts driven by 1 hp motor, has Emerson FX-490 servo drive, GE fanuc 90-30 PLC. Includes power take off table.

Stock# 49834001

Used- Cincinnati Milacron 91" Wide Sheet Line. Consisting of the following components: (1) 6" screw diameter Apex Single screw extruder 38:1 L/D Ratio Side vented including vacuum pump located 88" back from end of barrel. Electrically heated air cooled barrel having 7 barrels zones of heating. Unit is direct connected with a 500 hp DC Motor thru a 13.844:1 ratio, extruder centerline is 61". SCR DC drive and control panel having 7 barrels zones and 13 downstream zones. (1) 4.5" screw diameter Apex Single screw extruder 34:1 L/D ratio side vented including vacuum pump located 55" from end of barrel. Electrically Heated Air Cooled barrel approximate 7 zones for barrels and 7 zones for downstream. Direct connected 250 hp DC motor thru 14.036:1 gearbox ratio. DC drive control. Each extruder is equipped with a hydraulic Dynisco 6" and 4.5" screen changer with hydraulic power unit. Two MAAG gear pumps for each of the extruders. With die stand and die block . 88" wide Model UHRC-200-FG restrictor bar die. Rectangular feed. (1) Cincinnati Milacron Three roll down stack individually driven rolls top roll is 20" diameter x 91" wide Chrome mirror finish, middle and bottom rolls are 36" diameter x 91" wide both rolls are chrome with mirror finish. All rolls driven by a 5 hp motor thru gearbox. Hydraulically operated roll closure and each are cooled by AEC packaged chilling units. Cooling conveyor equipped with a Scan Tech MFG 2011 with controls. Pull Roll stand having 8" diameter x 91" wide. Control system and console. Mfg 2001.