Waste Water Equipment

Used 140 Cu Ft Dual Shaft Ribbon Blender – Stainless Steel Industrial Mixer

Used Dual Shaft Ribbon Blender, Approximately 140 cuft / 1100 Gallon capacity. Stainless steel. Dimple Jacket. Bottom Discharge: (2) 10" ports, one for each screw, Trough dimensions: Length: 119 inches Height: 46 inches Width: 47 inches. Height off ground: 12 inches Bottom discharge. (2) 575 Volt, 15 HP motors. (Motors will be switched out to (2) Used US voltage Motors;

Used 14,000 Gallon 316L Stainless Steel Vertical Tank – Erected Steel Products, API-650, Side Agitator

Used- Erected Steel Products 316L Stainless Steel Vertical Tank, 14,000 gallons. 13' diameter X 15' high straight side. Rated ATMOS @ 20 to 160 F. S/N 1172. API-650 standard. Slight cone top, flat bottom with ramped side. Top fittings: 20" manway, (1) 6" vent, (1) 2", and (1) 16" X 16" feed inlet. 24" side bottom manway, (1) 2.5", (2) 10", (1) 3", and (1) 6" side inlet and outlets. (2) 8" side bottom outlets. Built 2012. Agitator in hot;s not included.

Used 14,000 Gallon 316L Stainless Steel Vertical Tank – Erected Steel Products, API-650, Built 2012

Used-14,000 gallon Erected Steel Products 316L Stainless Steel Vertical Tank. 13' diameter X 15' high straight side. Rated ATMOS @ 20 to 160 F. S/N 1168. API-650 standard. Slight cone top, flat bottom with ramped side opposite where agitator was mounted (agitator no longer available). Top fittings: 20" manway, (1) 6" vent, and (1) 12". 24" side bottom manway, (1) 2" (1) 3", (1) 6", (3) 8", (3) 10" and (1) 12" side top inlets (2) 8" side bottom outlets. Built 2012.

Used 14,000 Gallon 316L Stainless Steel Vertical Tank – Erected Steel Products, API-650, Agitated, Built 2012

Used-14,000 gallon Erected Steel Products 316L Stainless Steel Vertical Tank. 13' diameter X 15' high straight side. Rated ATMOS @ 20 to 160 F. S/N 1169. API-650 standard. Slight cone top, flat bottom with ramped side opposite where the agitator was mounted (agitator no longer available). Top fittings: 20" manway, and (1) 6" vent. 24" side bottom manway. (1) 12" and (1) 24" side top inlets. (1) 6" , (1) 8", and (1) 10" side inlets. (1) 2.5", (2) 8", (1) 3", and (1)4" side bottom outlets. Built 2012.

Used – Aurora Industrial Machining Horizontal Shell & Tube Heat Exchanger – 150 PSI, Carbon Steel

Used Aurora Industrial Machining Horizontal Shell & Tube Heat Exchanger, Approximately 142 square feet. Carbon Steel shell rated 150psi at -20 to 350 Degrees F. (109) 304 stainless steel straight tubes, 0.625" diameter, rated 150psi at -20 to 350 Degrees F. Openings shell: 2" (inlet), 2" (outlet), 2" (relief), tubes: 8" (inlet), (4) 3/4" (vent/drain). National Board# 3012, Serial# 4095, built 1996.

MFR: Aurora

Industrial Unused Southern Heat Exchanger Shell & Tube Heat Exchanger – 1459 Sq Ft, 304L Stainless Steel

Unused- Southern Heat Exchanger Shell & Tube Heat Exchanger, Approximately 1459 Square Feet, 304L Stainless Steel, Horizontal. 304L Stainless steel shell rated 103 psi at -20 to 250 degrees F. (186) 304L Stainless steel 1-1/2" diameter x 19 11-3/4" long, rated 127 psi at -20 to 250 degrees F. 304L Stainless heads and tubesheet. Openings: (4) .75", (1) 1-1/2", (2) 8", (2) 12". Saddle mounted. National Board# 15648, Serial# 20-0055, Built 2020.

MFR: Southern Heat Exchanger

Unused Anhydro SCAN-VIBRO Pilot Fluid Bed Dryer – Stainless Steel Pilot Drying System with Mobility (2025)

Unused- Anhydro SCAN-VIBRO Pilot Fluid Bed Dryer, Model Pilot Plant Fluid Bed. Effective fluid bed area: 8.6 Sq. feet (0,8 m2). Stainless steel. 200cm (78.74") length 40cm (15.74") Diameter Tube. 9.75" (250 mm) diameter inlet tube. 11.7" (300 mm) diameter outlet tube. Frame mounted. ON 4 wheels. Control panel. Overall dimensions 98" (3000 mm) L x 26" (800 mm) W x 72" (2200 mm) H, Weight 1 tonnes. New year 2025. Our Freight specialists can assist with any customs documentation to insure a smooth transition.

MFR: Anhydro

Used Lee RA-150 150-Gallon 316 Stainless Steel Jacketed Kettle with Scrape Surface Agitation

Used Lee RA-150 150-Gallon 316 Stainless Steel Jacketed Kettle with Scrape Surface Agitation. Serial Number 84164-1-4. 316 Stainless Steel construction. Jacket Rated 90PSI at 332 Deg F, 90PSI at -20 Deg F at 90PSI. Inside dimensions: 42" ID x 40.5" deep. Center bottom outlet 2 " ferrule for Cherry Burrell valve (no valve). Single motion scrape surface agitation w/1.5HP drive and baffle. Two-piece cover. Has Thermometer and Sprayball. Built in 2014.

MFR: Lee Ind

Used Hamilton Style CW 150-Gallon Tilting Kettle – 316 Stainless Steel, Jacketed

Used- Hamilton Style CW Tilting Kettle, 150 Gallon, 316 Stainless Steel. Approximate 44" diameter x 40" deep. Open top, jacketed hemispherical bottom. 304 Stainless steel jacket rated 100 psi at -20 to 328 degrees F. Top entering angled anchor style agitator with scrapers, driven by a 2 hp, 3/60/208-230/460 volt, 1750 rpm gear motor, approximate 44.32 to 1 ratio (no gearbox tag). Air operated agitator tilt, motorized bowl tilt, pouring lip. 3" Center bottom outlet with valve. Mounted on a stainless steel frame with (3) leg. National Board # 17. Serial # F-4662-3. Built 2002.

MFR: Hamilton

Industrial Hamilton CW 150-Gallon Steam Jacketed Kettle – Motorized Tilt

Used- Hamilton Style CW Tilting Kettle, 150 Gallon, 316 Stainless Steel. Approximate 44" diameter x 40" deep. Open top, jacketed hemispherical bottom. 304 Stainless steel jacket rated 100 psi at -20 to 328 degrees F. Top entering angled anchor style agitator with scrapers (missing 1 scraper), driven by a 3 hp, 3/60/208-230/460 volt, 1750 rpm gear motor, approximate 44.32 to 1 ratio (no gearbox tag). Air operated agitator tilt, motorized bowl tilt, pouring lip. 3" Center bottom outlet with valve. Mounted on a stainless steel frame with (3) leg. National Board # 278. Serial # F-5817-2. Built 2004.

MFR: Hamilton

Hamilton 150-Gallon Tilting Kettle – Stainless Steel, Steam Jacketed, Food-Grade

Used- Hamilton Style CW Tilting Kettle, 150 Gallon, 316 Stainless Steel. Approximate 44" diameter x 40" deep. Open top, jacketed hemispherical bottom. 304 Stainless steel jacket rated 100 psi at -20 to 328 degrees F. Top entering angled anchor style agitator with scrapers (missing 2 scraper), driven by a 2 hp, 3/60/208-230/460 volt, 1750 rpm gear motor, approximate 44.32 to 1 ratio. Air operated agitator tilt, motorized bowl tilt, pouring lip. 3" Center bottom outlet with valve. Mounted on a stainless steel frame with (3) leg. National Board # 279. Serial # F-5817-3. Built 2004.

MFR: Hamilton

Industrial Alfa Laval Spiral Heat Exchanger – 150 Sqft | 7°F MDMT | 50 PSI

Used Alfa Laval Spiral Heat Exchanger, Model 1H-SW-1W. Approximately 150 square foot. Rated 50 psi at -7 to 200 degrees F on both A and B circuits. Stainless steel contact parts. (4) 6" Diameter openings. Hinged front bolt on cover. Mounted on (2) legs. National Board # 20041, Serial# 30112-69683, built 2014.