Food and Beverage Equipment
Stock No.:
54228003Used Patterson Kelley 3 Cu. Ft. Twin Shell Dry V-Blender – Stainless Steel
Used Patterson Kelley 3 Cubic Foot Twin Shell Dry V-Blender, Stainless Steel. 3 cubic foot capacity. Max material density 70 lbs./cubic foot. Top charge ports with covers. 16" diameter x 26" long vessel sections. 6" Diameter center bottom outlet with 41" discharge height. Driven by a 3/4hp, 3phase 50/60 hz, 208-220/440 volt, 1725/1425rpm motor. Mounted on painted carbon steel frame. Serial# 147566.
MFR: Patterson Kelley
Stock No.:
50467039Buy Used Ketema Shell & Tube Heat Exchanger – 3.2 Sq. Ft., High-Pressure Rated
Used- Ketema Shell & Tube Heat Exchanger, 3.2 Square Feet, Type MVHT-1-A-SS. (28) .375" diameter x 14" long 316 stainless steel tubes rated 300 psi and full vacuum at 650 degrees F. Carbon steel shell rated 150 psi at 400 degrees F. Size 4-Y-14. 1.5" tubes inlet/outlets, 1" shell inlet/outlets. Serial # WL-950429/2.
MFR: Ketema
Stock No.:
50467040Used Ketema MVHT-1-A-SS Shell & Tube Heat Exchanger – 3.2 Sq. Ft., 300 PSI
Used- Ketema Type MVHT-1-A-SS Shell & Tube Heat Exchanger, 3.2 Square Feet. (28) .375" Diameter x 14" long 316 stainless steel tubes rated 300 psi and full vacuum at 650 degrees F. carbon steel shell rated 150 psi at 400 degrees F, Size 4-Y-14. 1.5" tubes inlet/outlets, 1" shell inlet/outlets. Serial # WL-950429/A1,
MFR: Ketema
Stock No.:
10755151Gloucester Model 35250R2 3.5" Diameter Single Screw Extruder – Industrial Used
Used- Gloucester Model 35250R2 3.5" Diameter Single Screw Extruder. 3.5" diameter screw, 32:1 L/D. Has an electrically heated, air cooled, vented, and plugged barrel at approximately a 65? center line height. Barrel is set up for Contra-Cool but does not include blower. Gearbox has a reduction ratio of 18.17:1 and is direct driven in a wraparound manner by a 100 HP Baldor D/C motor with Saftronics SCR control. One (1) HP pump with heat exchanger on the gearbox. Originally manufactured in 1995 and completely reconditioned in 2011 and never put back into service. All wiring on the extruder is run to a terminal strip. New control panel has fourteen (14) zones of temperature controls. Drive control is loose. Includes three (3) new / rebuilt screws. 460/3/60. Serial# 36736/12.
MFR: Gloucester
Stock No.:
10755147Used Tria Model 900 NS-R Pull Roll Granulator – High-Performance Industrial Granulator
Used Tria Model 900 NS-R Pull Roll Granulator. 12.5" x 40" feed throat (1020mm x 320mm). Five (5) knife open rotor with two (2) bed knives. Rotor is belt driven by a 22 Kw (30 HP). Feed hopper with rear mounted 36" wide steel / serrated pull rolls. Air actuated feed rolls are powered by a 1 Kw (1.5 HP) A/C motor. 9" x 19.5" front material hopper entrance. 12.6 Kw (17 HP) blower discharge with Kongskilde OK160 piping and cyclone with filter bag. Approximate production rate of 400-600 kg/hr. (880-1320 lbs./hr.). Includes free standing panel with controls. 480/3/60
MFR: Tria
Stock No.:
10128120Used Granutec 1216PG-30 Plastic Granulator | 30 HP Industrial Plastic Grinder
Used Granutec 1216PG-30 Plastic Granulator | 30 HP Industrial Plastic Grinder. The serial number is 302-3795. The throat is 11" by 11". It has 7 knives. The motor is 30 hp and requires 230/460 vac 3 ph and goes 1760 rpm. On casters.
MFR: Granutec
Stock No.:
50467035Used Gaspar 30-Gallon Reactor – 316L SS, 150 PSI, 5 HP Chemineer Agitator
Used- Gaspar Reactor, 30 Gallon. 316L Stainless steel construction, approximately 24" diameter x 24" straight side, Elliptical removable top, elliptical dish bottom. Internal rated 150 psi and full vacuum at 400 degrees F. Jacket rated for 150 psi at 400 degree F. Top mounted 5 hp Chemineer agitator drive with mechanical seal, 230/460 volt XP motor. Center bottom outlet. Mounted on (4) painted carbon steel legs. Serial# 495032, National Board# 821.
MFR: Gaspar Inc.
Stock No.:
49307005Used Great Western Manufacturing Type TB, Model 611/4 Tru-Balance Screener
Used- Great Western Manufacturing Tru-Balance Screener, Type TB, 30" Diameter, Model 611/4 (QA30), 304 Stainless Steel. Approximate 500 pounds per minute with wheat flour. Approximate 30" diameter, (4) sieves. Approximate net sieving area 15 square feet. Driven by a 1.5 HP, 3/60/230/460 volt, 1160 rpm motor. 5" top opening, bottom openings: 5", 4". Mounted on a painted carbon steel frame. Serial# 3882. Built 1999.
MFR: BF Gump
Stock No.:
44496015Used Andritz Sprout-Bauer DSF1518 Granulator – 30HP, Film Granulation, 7 Knife Rotor
Used- Andritz Sprout-Bauer Granulator, Model DSF1518. 7 knife rotor, 2 bed knife. Driven by 30HP, 3/60/460 Volt only motor. Belt driven 5? x 18? blow-in in-feed hopper, vacuum take off discharge. Mounted on a short leg base. No starter or controls. Designed for film granulation. Serial# 2000-00373.
MFR: Sprout Bauer
Stock No.:
44496016Industrial Plastic Granulator – Andritz Sprout-Bauer DSF1518, 30HP, Film Recycling
Used- Andritz Sprout-Bauer Model DSF1518 Granulator. 7-knife rotor, 2 bed knife. Driven by 30 HP 460 volt only motor, belt drive. 5" X 18" blow-in in-feed hopper, vacuum take-off discharge. Mounted on a short leg base. No starter/controls. Designed for film granulation. Previously used for recycling polyester film edge trim.
MFR: Sprout Bauer
Stock No.:
44496018Used 30HP Plastic Granulator – Andritz Sprout-Bauer DSF1518, 7-Knife Rotor
Used- Andritz / Sprout-Bauer 30HP Model DSF1518 Granulator. 7-knife rotor, 2 bed knife. Driven by 30 HP 460 volt only motor, belt drive. 5" X 18" blow-in in-feed hopper, vacuum take-off discharge. Mounted on a short leg base. No starter/controls. Designed for film granulation. Previously used for recycling polyester film edge trim.
MFR: Sprout Bauer
Stock No.:
54115001Used Tolhurst 30” Basket Centrifuge | Top Unload | 0–1000 RPM | Stainless Steel
Used- Tolhurst Basket Centrifuge, Size 30", 0-1000 basket rpm, 70lbs/cu. ft maximum throughput. Stainless steel contact parts. Top Unload, Perforated basket. stainless steel bolt on top with clamp down cover, 6" sight glass. Cover has (2) 2-1/2" threaded inlets. Vessel approximately 30" diameter x 18" straight side. 4" side bottom outlet down to 1-1/4" threaded. 3 point mount on carbon steel frame with casters. Serial# TA-38533. Includes Hydraulic Drive skid, driven by a 7.5hp 3/60/230/460v 1175rpm motor through reducer, and a mounted Control Panel.
MFR: Tolhurst