Food and Beverage Equipment
Stock No.:
52862016Doyle and Roth Vertical Shell and Tube Condenser
Used- Doyle and Roth Vertical Shell and Tube Condenser, Approximate 19.6 Square Feet. Carbon steel shell rated 150psi / FV external at -20 to 400 degrees F. (55) 3/4" Diameter x 24" long Hastelloy C-276 tubes rated 15psi / FV at -20 to 450 degrees F. Approximate 12,733 BTU/h.Single pass. 3.875" Baffle spacing. Side lug mounted. National Board# 20736, serial# S1993-2.
MFR: Doyle & Roth
Stock No.:
10128086Used 1,900 Gallon JV Northwest Stainless Steel Jacketed Tank with 3 HP Agitator – 45 PSI, UM Stamped
Used 1,900 Gallon JV Northwest Stainless Steel Jacketed Tank with 3 HP Agitator 45 PSI, UM Stamped, Serial # 13847, Built 1997. Jacket in two sections is rated for 45 PSI @ 400 degree F. Tank is 78" diameter x 84" straight side. Bottom and 1/3 of the straight side jacketed. Tank has bottom mounted 3 hp agitator, 230/460 vac 3 ph power required. Top has 20" round manway with hinged lid, 10" vent pipe, one 6" tri clamp, two 3" tri clamp, and one 2" tri clamp. Jackets have two threaded connections each. Bottom has 4" 90 degree tri clamp elbow for the discharge. Side has .75" coupling with probe. Unit has four carbon steel legs.
MFR: JV Northwest
Stock No.:
51258018Used Strong Scott Stainless Steel Double Spiral Ribbon Blender, Model IMXS, 193 Cu Ft, 50 HP XP
Used Strong Scott Stainless Steel Double Spiral Ribbon Blender, Model IMXS, size 50.12-6. Approximate 193 cubic foot capacity. With top cover and bag dump station. 50 HP XP motor & reducer. Center bottom outlet with rotary valve. Serial# 2817.
MFR: Strong Scott
Stock No.:
44284Used Alpine Ultraplex Cross Flow Mill B1000UP – 195 HP, Carbon Steel, Industrial Grinder
Used- Alpine "Ultraplex" Cross Flow Mill, Type B1000UP. Material of construction is Carbon Steel. Cast iron housing with swing back door. Top feed but without feed hopper. Baffle ribbed grinding tracks. Belt driven by a 195 hp (130 kw)-380volt/50cycle/3ph motor. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.
MFR: Alpine
Stock No.:
10151501Alloy Fabricators Approximately 1,950 Gallon Mix Tank with Internal Coils
Used- Alloy Fabricators Approximately 1,950 Gallon Mix Tank with Internal Coils. 304 Stainless Steel Jacketed. 78" diameter x 81" straight side; Dished top and bottom; Internal rated 15/FV at 335 degrees F; Jacket rated 44 psi at 335 degrees F; Coils rated 44 psi at 335 degrees F; (4) side wall baffles; 7.5 hp axial type agitator, 304 stainless steel, Foam breaker at top - 2 blade, 51" dia; dual hub with 3 blades - upper 50" dia; lower 30" dia, 18" dia. 2 blade radial flow at bottom. Serial # 1-151A; Built 1991.
MFR: Alloy & Steel Fab
Stock No.:
54110002Used Doyle & Roth Shell & Tube Heat Exchanger | 1963 Sq. Ft. | Alloy 400 Tubes | 300 PSI | 2006/2018
Used Doyle & Roth Shell & Tube Heat Exchanger | 1963 Sq. Ft. | Alloy 400 Tubes | 300 PSI | 2006/2018. Monel/Alloy 400 tube side construction. Full vac/300 psig shell side design pressure; 390 psig shell side test pressure; 650/15 degrees F shell side max./min. design temp.; 1 pass shell side. Full vac/250 psig tube side design pressure; 325 psig tube side test pressure; 650/15 degrees F tube side max./min. design temp.; 3 pass shell side. OAD: 32" D x approx. 248" L. (300) 1.25" D x 240" L tubes. Built 2006, Repaired by Ohmstede in 2018. NB #20179. Original SN S-1443-4, new SN 824114.
MFR: Doyle & Roth
Stock No.:
52283010Used Van Dorn Model G-200 Plastic Grinder / Granulator.
Used- Van Dorn Model G-200 Plastic Grinder / Granulator. Mild steel construction. Chamber measures 6-1/2" X 6-1/2" with 14" x 6" feed throat. Includes (3) rotating blades and (2) stationary blades with 7/16" (0.437") screen and 9" center bottom discharge. Driven by 2 HP, 230/460 volts, 3-phase, 60 Hz, 1140 RPM motor. Mounted on mild steel frame on casters. Serial# 283-B.
MFR: Van Dorn
Stock No.:
54540001Used Apex Type 583 Stainless Steel Double Cone Blender – 2 Cubic Foot (58 Liter) Capacity
Used- Apex Double Cone Blender, Type 583. 2 cubic foot (58 liter) capacity. Stainless steel construction. .5 HP, 115V drive with 19:1 direct drive speed reducer. Previously used for agricultural products.
MFR: Apex
Stock No.:
10755152Used Gloucester 25225R2 Single Screw Extruder – 2.5" Dia., 32:1 L/D, 60 HP Motor
Used- Gloucester Single Screw Extruder, Model 25225R2. 2.5' Diameter Screw, 32:1 L/D. Has an electrically heated, air cooled, and non-vented barrel at approximately a 65? center line height. Barrel is set up for Contra-Cool but does not include blower. Gearbox has a reduction ratio 13.75:1 and is direct driven in a wraparound manner by a 60 HP Baldor D/C motor with Saftronics SCR control. One (1) HP pump with heat exchanger on the gearbox. Originally manufactured in 1995 and completely reconditioned in 2011 and never put back into service. All wiring on the extruder is run to a terminal strip. New control panel has fourteen (14) zones of temperature controls. Drive control is supplied loose. Includes two (2) new / rebuilt screws. 460/3/60. Serial# 36736/25.
MFR: Gloucester
Stock No.:
10755143Used Gloucester 2522 R2 2.5" Extruder – 60 HP, 32:1 L/D, Reconditioned
Used-Gloucester Model 2522 R2 2.5" 32:1 L/D Extruder with an electrically heated, water cooled (closed loop) vented and plugged barrel at approximately a 72" centerline height. Gearbox has a reduction ratio of 10.73:1 and is direct driven by a 60 HP D/C motor with Saftronics SCR control. Manual screen changer mounted on the extruder discharge. Includes panel with controls. Reported to be reconditioned.
MFR: Gloucester
Stock No.:
10755144Used Gloucester 2.5" Single Screw Extruder – 32:1 L/D, Air-Cooled & Vented
Used- Gloucester 2.5" Extruder 32:1 L/D five (5) zone air cooled and vented barrel at a 45" centerline height. Top center feed throat. Driven by a 50 HP A/C 1750/2100 RPM motor, includes 6 zone temperature control panel and 5-hole strand die
MFR: Gloucester
Stock No.:
10128090Used Patterson-Kelley 20 cu. ft. Stainless Steel Twin Shell “V” Blender | 3 HP Drive | Platform & Safety Fencing | Good Condition
Used Patterson-Kelley 20 cu. ft. Stainless Steel Twin Shell V" Blender | 3 HP Drive | Platform & Safety Fencing | Good Condition. The blender is chain and sprocket driven by 3 hp electric motor. The blender is designed to handle material density of up to 105 lbs/cuft. The two shells measure about 31" diameter x 53" long. This unit is set up for an intensifier bar belt driven by a 5 hp motor. THE BAR ITSELF IS MISSING. There is a 7.5" discharge with a pneumatically operated butterfly valve. Overall dimensions with carbon steel stand are 116" wide x 68" deep x 112" tall. Serial # 234005. This unit comes with fence panels for a safety and a platform with a stairway. The platform is 103" wide x 83" deep x 48.5" tall to the floor. OAD of the platform with stairway are 103" w x 112" long x 91" h. Requires 230/460 vac 3 ph electrial supply. Good condition.
MFR: Patterson Kelley