Cosmetics Equipment

Used Extru-Tech E-325 Single Screw Extruder – 150-800 Lbs/Hr

Used- Extru-Tech Model E-325, Single Screw Extruder. Unit designed primarily for research and development purposes. 3.25", Approximately 40 HP motor, Can process between 150 to 800 pounds per hour (68 to 363 kilograms per hour). The E-325 is equipped with a 6x30 single-shaft conditioner, an accurate feed system, a knife drive, and a control panel with a variable frequency drive (VFD) panel operating at 230 volts.

MFR: Extrutech

Used Olson / V-RAM Double By-Products Pumping System | 5,000 lbs/hr | Dual 50 HP Hydraul

Used Olson Mfg. Co. dba V-RAM Pumps Double By-Products Pumping System. (2) Identical Stainless Steel Pumps, approximately 5000 lbs/hr working capacity, with 679 max psi per each pump. 30-1/2" long x 14" wide x 15-1/2" deep infeed. Approximately 54" long trough with 11" ram head. 6" diameter outlet with gate valve, 10" discharge height. Includes Double B-Style Hydraulic Unit skid with air cooler. (2) 50hp 3/60/230/460v 1775rpm motors. Includes Control Panel.

Valmet Pre-Compression Plug Feeder & Shredder System – 1000 BDST/D Biomass Capacity

Unused Valmet Plug Screw Feeder with Pre-Compression Screw and Shredder. Designed for infeed raw material chips density 100 kg/m3, moisture content 20-48%, design flow rate 530 dry tons per day soft wood chips, (500BDST/D); Max capacity 1000 BDST/D; Turndown rate 50%. Valmet plug screw feeder: Fed by a pre-compression screw section, and 48" shredder at outlet; 850 HP Siemens motor 1750 rpm 460v 3/60; Gear Reducer ratio 25:1. Nominal speed 69 rpm, range 35-105 rpm; Inlet 35.83" x 25.79". Pre-compression screw: Materials of construction stainless steel 304L for all contact parts; Sits on top of plug screw at 90 degrees with s 24" diameter top force feed; Capacity Volume/Revolution inlet/discharge: 45 L / 22.5 L. Capacity / revolution at 110 kg/m3 = 5.46 BDST/D and net max capacity at 110 kg/m3 = 530 BDST/D; 250 HP motor 1750 rpm 460v 3/60 v-belt drive to gear reducer V-belt reduction 1:52; Gear reducer SEW Eurodrive ratio 18:1. Final rpm nominal speed 65 rpm, range 45-97 rpm; Outlet: 35.83" x 25.79". T-Pipe 48" Shredder: Fed from plug screw feeder 24" biomass inlet; MAWP 350 psig at 800F; 100 HP motor 1750 rpm 460v 3/60; Gear reducer 8.9:1 for nominal 197 rpm; Outlet 24" flange 600#. All equipment never used, new in 2020. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.

Used Niro Mobile Minor Spray Dryer – Stainless Steel | With Atomizer | Serial #1952

Used Niro Mobile Minor Type HT Portable Spray Dryer, Stainless Steel. Approximate 32" diameter x 24" straight side. Drying capacity approximate 2.2-15.4 lbs (1-7 kilos) an hour. Electrically heated, temperature approximately up to 350 degrees C. Top entering Niro rotary atomizer, air driven. Includes cyclone, control panel. Center bottom outlet. On wheels. Serial# 1952.

MFR: Niro

Used York Chiller Starter/Control Panel – 4160V | 60Hz | Built 2017 | High Voltage Control

Used- York Chiller Starter/Control Panel. 4160V nominal rated voltage; 4576 max. continuous voltage; 3744V min. continuous voltage; 60Hz. Built 2017.

MFR: York

Used Battery Recycling Systems Lead Refining Kettle Air Filtration System – 30,000 CFM, 150 HP Blower, Bag House, BRS/Wirtz

Used- Battery Recycling Systems, Inc. a sub-div. of Wirtz. Complete system consisting of a Lead Refining Kettle Air Filtration System. This system captures exhaust and fumes from the lead refining process through a sanitation hood mounted on the refining kettle, directing them into a bag house air filtration unit. The setup features a multi-cell bag house configuration with drop-out boxes, approximately 60 feet of internal plant ducting connected to each kettle's sanitation hood, a specialty air recirculation blower, and an automatic filter bag cleaning system with integrated dust collection. Processed air is discharged via a chimney stack, which must be constructed on-site by the customer per BRS prints due to its size. The system operates on 460V, 3-phase, 60Hz, with 3-wire and 24 VDC control voltage. It includes standard fasteners, uses English units, requires layout approval, and features equipment painted in RAL-5015 (Sky Blue) for carbon steel components and RAL-1018 (Zinc Yellow) for safety guards. NEW YORK BLOWER BC-30 SIZE 36 BC ARR-1 POS-Z CW ROTATION TAU DISCHARGE FLANGED MOTOR; INTEGRAL TE 150HP 1800RPM 3-60-460 PREMIUM EFF. 445T BALDOR, CAPACITIES: 30000 CFM, 18IN WG, 2207RPM, 132BHP, 0.0607 LB/FT^3, 4400FT 70 F.

New MKM CD 250 Atomizer – 9000–13,000 RPM, SS316 Spray Disk, RPM Sensors, Insulated Jacket

Unused / New MK Manufacturing Co, Atomizer, Model MKM CD 250 features a feeder cover, retainer, sleeve, and feeding pipe made from SS 316 stainless steel, all tested, machined, and balanced as required, the spray disk is also SS 316, precisely machined and balanced, the main shaft is constructed from special spring steel with centerless grinding for high precision, bearing housing is fabricated from mild steel with cylindrical surfaces to accommodate bearing seats, the shaft is driven by a V-belt pulley system, operating speed ranges from 9000 to 13000 RPM and includes RPM sensors and a digital display, the atomizer jacket is insulated with ceramic wool, air purging is provided to prevent sediment buildup and ensure continuous spray dryer operation, lubrication is handled by an MKM make pump with motor, double filters, and gauges for continuous oil flow, the unit is supplied without a motor, compatible with a 25 HP, 2900 RPM flange-mounted Siemens or Hindustan motor, the atomizer pulley is made from SS 304 while the motor pulley is made from cast iron or mild steel. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.

New MKM CD-210 Rotary Disk Atomizer – SS316, 19,000 RPM, F-35 Compatible, Includes Toolkit

New MKM CD-210 Rotary Disk Atomizer SS316, 19,000 RPM, F-35 Compatible, Includes Toolkit. Constructed of 316 stainless steel. The atomizer features key components in SS 316 stainless steel, including the feeder cover, retainer, sleeve, feeding pipe, and spray disk (?210 mm), all precision-machined and dynamically balanced at 19,000 RPM. The main shaft is spring steel, centerless ground for high concentricity and strength. The mild steel bearing housing includes precision-machined seats for alignment. Power is delivered via a V-belt pulley system. Operating speed matches existing F-35 units, with jacket and dimensions ensuring full interchangeability. An MKM oil pump system provides continuous automatic lubrication, with oil temperature maintained below 75C at 10 TPD. RPM range: 9,00018,000; vibration remains within specified limits. Includes RPM sensor/display and a maintenance tool kit with pullers, spanners, and locknut tools. Compatible with and replacement for an F-35 atomizer. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.

Used RefTec Shark R134a Recovery & Recycling System – AHRI 700 Standard, Single-Pass Reclaim

Used- RefTec Shark Recovery and Recycling System. Cleans dirty R134a back to ARI 700 standard reclaimed gas in a single pass. Removes oil, acids, moisture and hard particulates from even the dirtiest of gases. For every 1% of contamination the Shark Reclaim Unit removes, 2% of efficiency has been restored. R134a Rates : 5.34lbs/min (2.42kgs/min) direct liquid; 2.89lbs/min (1.31kgs/min) vapor; 2.03lbs/min (.92kgs/min) recycle; Certified by AHRI 740, ETL, UL-1963.

Pre-Owned Dispermat CA40-C1 Lab Dissolver – 50?mm Saw Disc with Control Panel

Used VMA-Getzmann Lab Dissolver, Type Dispermat CA40-C1. Stainless steel in product contact parts. 11.7" (300 mm) shaft. 1.95" (50 mm) dia. saw disc. Complete with control panel. Serial # A1000637. New year 2011. Previously use in an R&D application. Over all dimensions: 31.2" (800 mm) long x 23.4" (600 mm) width x 23.4" (850 mm) high. Weight 220 lbs (100 kgs). Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.

Used Aeromatic Aeroglide C1 120-65 RGC Fluid Bed Dryer – 5,000 lbs/hr, Stainless Steel, Natural Gas, Built 2005

Used- Aeromatic Aeroglide Dryer, Model C1 120-65 RGC. Up to 5000 lbs/hr (dependent on product); Drying Bed Area 350 sq. ft. drying area; 140 sq. ft. cooling bed area; 9'9" bed width; 152.4mm (6") max. first stage bed depth; 152.4mm (6") max. second stage (cooling) bed depth; Food grade 304 stainless steel construction; Natural gas fueled. 3/60/460V. SN 05153-02. Built 2005.

MFR: Aeromatic

Used Carrier Fluid Bed Dryer – Model FTDAD/C2460S, Gas-Fired, 24" x 5.5' Heated Section, Carbon Steel

Used- Carrier Fluid Bed Dryer, Model FTDAD/C2460S. 24" wide x 56 heated section and 2 cooling section. Gas fired. Carbon steel wetted parts. 316 strokes. 890 rpm, 460 volt. Built 2012.

MFR: Carrier