Cosmetics Equipment

Used Cowles model 720 VH disperser has a stainless steel shaft length of 50" and a blade diameter of 14". Unit is equipped with an air over oil lift. Driven by a 40/20 hp motor that runs1750/870 rpm ...

Used-Cowles model 720 VH disperser has a stainless steel shaft length of 50" and a blade diameter of 14". Unit is equipped with an air over oil lift. Driven by a 40/20 hp motor that runs1750/870 rpm and requires 220 vac, 3 ph electricity. The motor is tagged for hazardous location however the junction box attached to the motor does not appear to be. Serial no. 720 C46 Overall dimensions are approximately 54" w x 94" l x 78" h.

MFR: Cowles

Used This Cowles disperser has a stainless steel shaft length of 52" and a blade diameter 14". Unit is equipped with an air over oil lift. Driven by a 40/20 hp, 1800/900 rpm motor that requires 230 v...

Used-This Cowles disperser has a stainless steel shaft length of 52" and a blade diameter 14". Unit is equipped with an air over oil lift. Driven by a 40/20 hp, 1800/900 rpm motor that requires 230 vac, 3 ph electricity. Overall dimensions are approximately 54" w x 90" l x 80" h.

MFR: Cowles

Used Progressive Industries, Inc model MS-20 air classifier only. Carbon steel construction. For particles 3 microns down to 0.4 micron average diameter. It can handel feed rates of 1 ton to 20 tons ...

Used-Progressive Industries, Inc model MS-20 air classifier only. Carbon steel construction. For particles 3 microns down to 0.4 micron average diameter. It can handel feed rates of 1 ton to 20 tons per hour. The diameter of the chamber is 46" and the overall length is about 119". The rotor is driven by a 20 hp, 230/460 vac 3 ph electric motor. This unit is for air classifing after milling. Serial # 88 14.

Used Hi Speed Disperser has two 50" stainless steel shafts with two 8" diameter blades on each. Unit is equipped with an air over oil lift. Variable speed. Driven by a 20 hp, 1755 rpm motor that re...

Used-Hi Speed Disperser has two 50" stainless steel shafts with two 8" diameter blades on each. Unit is equipped with an air over oil lift. Variable speed. Driven by a 20 hp, 1755 rpm motor that requires 230/460 vac, 3 ph electricity. Overall dimensions are approximately 32" w x 80" l x 80" h. Motor is tagged for hazardous location.

Buy Used Blue M POM-371A-2 Oven – 8.25 Cu Ft, Electrically Heated

Used- Blue M Model POM-371A-2 Oven. 8.25 Cubic feet capacity. Maximum temperature 212 degrees F (100 C). Stainless steel interior, inside dimensions measure 27" wide X 20" high X 24" deep. Electrically heated, rated for 208/240 Volts, Single phase, 60 Hz. B.O.M. NO. E3-00041. Serial# P20-312.

MFR: Blue M

Used Sargent single-pass continuous conveyor dryer. The dryer has a 3 heating zone system, each with an electric heat source. The first zone appears to have a 350° F maximum temperature and zones two...

Used-Sargent single-pass continuous conveyor dryer. The dryer has a 3 heating zone system, each with an electric heat source. The first zone appears to have a 350° F maximum temperature and zones two and three appear to have a 700° F maximum temperature based on the original drawing. The conveyor dyer has a 20.5" wide stainless steel perforated conveyor belt that passes through a 210" long x 78" wide x 85" tall tunnel. The tunnel has three side access doors. The dryer has a 6" diameter inlet that is 124" from ground level and a 6" diameter outlet that is 30" from the ground. Overall dimensions of the unit are 295" long x 78" wide x 147" tall with drives and motors. Serial # 2036. Built 1976.

MFR: Sargent-Welch

Used AB Process / JBT Mixing System | 200 Gallon Jacketed Skid-Mounted Mixer

Used AB Process / JBT Mixing System | 200 Gallon Jacketed Skid-Mounted Mixer. Jacket rated 150 PSI at 366 degrees F. 36" straight side x 41" diameter tank dimensions, cone bottom. Scrape agitator. 15 HP SPX product pump. On Mettler Toledo load cells. Mounted on skid Built 2018.

MFR: JBT Foodtech

Used Hamilton 200-Gallon Stainless Steel Agitated Kettle – 120 PSI Jacket

Used- Hamilton 200 Gallon Agitated Kettle, stainless steel construction with 3/4 jacket, rated for 120 PSI at 342 degrees F. Features top mounted full sweep agitator, currently less drive. Hinged lid top covers. Hemispherical bottom with 2-1/2" diameter center bottom outlet.

MFR: Hamilton

Used Werner & Pfleiderer UK17 Double Arm Mixer – 200 Gal, Stainless Steel Clad, Jacketed

Used- Werner & Pfleiderer Double Arm Mixer, Model UK17, Stainless Steel Clad 200 Gallon. Sigma tangential blades, jacketed bowl (bottom only) 43" front-back x 53" left-right x approximately 36" deep. Geared both ends. Set up for hydraulic tilt 7.5 hp, 220/440V, 1750 rpm. No base, no drive. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.

MFR: Werner & Pfleiderer

Used Howard 200 Gallon Double Arm Mixer – 304 Stainless Steel, Hydraulic Tilt

Used- Howard Double Arm Mixer, Approximate 200 Gallon, 304 Stainless Steel. Non-jacketed bowl approximate 50" left to right x 44-1/8" front to back x 34-1/2" deep. Overlapping sigma blades set up for hydraulic drive, no power pack. Dual ram hydraulic tilt, top safety grate. Mounted on a stainless steel frame. Serial# H3649-2, built 2001.

MFR: Howard

Used 600 HP Schutte-Buffalo Hammermill with Twin City Blower, Heavy-Duty

Used- Schutte-Buffalo-Astec Model AHM-20 Carbon Steel Hammermill. Approximate 48" diameter x 50" wide rotor. Top feed with hopper, bottom discharge. Driven by a 600 HP, 3/60/460 volt, 1790 rpm motor. Mounted on a frame. Serial# 16088HM1. Includes a Twin City blower, Type RBR-SW, size 926, driven by a 200 HP, 3/60/230/460 volt, 1785 rpm motor. Astec serial# 16088HM1.

MFR: Schutte

Used Ross HDM-200 Double Planetary Mixer with 200 Gallon Capacity

Used Charles Ross & Son Model HDM-200 Double Planetary Industrial Mixer With 200 Gallon Maximum Working Capacity. Designed for heavy-duty batch mixing of compatible viscous and high-consistency materials, with an operating capacity range of 30 to 200 gallons. Equipped with (2) carbon steel planetary mixing stirrers operating at approximately 24 RPM orbital speed and 26 RPM stirrer rotation speed. Features a top dust hood with charging port, bottom fume hood and hydraulic lift system with dedicated hydraulic power pack for raising and lowering the mixing assembly. Includes (1) removable mixing can measuring 44" diameter x 33-3/4" deep. Driven by a 40 HP explosion-proof (XP) motor rated at 1,740 RPM, operating on 460 volts, 3-phase, 60 Hz electrical service. Power is transmitted through a Delroyd Model HV120 reduction gearbox with a 74.21:1 gear ratio. Mixer is mounted on a heavy-duty structural I-beam frame. Serial #35555. Additional mixing cans are available for purchase at an additional cost, subject to availability. Possible applications include batch mixing, blending, kneading and processing of compatible high-viscosity adhesives, sealants, coatings, pastes, putties, resins, polymer compounds, construction materials and other suitable industrial formulations.

MFR: Charles Ross