Contract Pharmaceutical Equipment

Used Sharples P-660 Decanter Centrifuge | 6000 RPM | Stainless Steel | 7.5 HP Main Drive | Mounted w/ Vibration Isolation

Used Sharples P-660 Decanter Centrifuge | 6000 RPM | Stainless Steel | 7.5 HP Main Drive | Mounted w/ Vibration Isolation. Stainless Steel. Main drive motor 7.5 hp 3/60/230-460 volts, fixed speed. Backdrive motor2 hp 3/60/208 230-460 volts fixed speed. 6000 rpm max speed, 95:1 gearbox. Mounted on table with vibration isolators.

MFR: Sharples

Pre-Owned Vulcan K6ETT Electric Counter Kettle | 6 Gal | 50 PSI

Used Vulcan-Hart Model K6ETT Electric Counter Tilting Kettle, 6 Gallon Capacity. Approximately 11.8" Diameter x 14-1/2" deep. Ellipsoidal bottom. 2/3 Jacketed rated 50psi at -20 to 300 degrees F. Frame mounted. National board# 21596, Serial# 46-3002235, Built 2011. 3/1PH 50/60HZ 8/10KW 208/240V requirements.

MFR: Vulcan

Lodige FKM600D Plow Mixer

Used- Lodige Model FKM600D batch-type plow mixer with 6 cubic feet working capacity and 10 cubic feet total capacity. 304 stainless steel, non-jacketed mixing chamber approximately 32" diameter x 50" long with 4" diameter shaft, (3) bolt-on plows, (2) bolt-on end scrapers, (2) 18" x 15-1/2" side access doors, and (2) 12" top openings. 9" x 7" bottom outlet with manually operated door and air-purge seals. Serial # 9046. Driven by an approximately 10 hp motor through Falk reducer. Includes control panel with Allen-Bradley PanelView 600 and SLC 5/04 CPU. Mounted on carbon steel stand. Suitable for dry powders, premixes, granular ingredients, spices, nutraceuticals, feed additives, chemical blends, and similar products.

MFR: Lodige

Used Sharples P-660 Super-D-Canter Centrifuge | 6000 RPM | New Motors & PLC Panel | Stainless Steel | 1-Year Warranty

Used Sharples P-660 Super-D-Canter Centrifuge | 6000 RPM | New Motors & PLC Panel | 1-Year Warranty, stainless steel construction (product contact areas, max bowl speed 6000 rpm, single lead conveyor w/welded hardfacing wear protection, base, casing, feed pipe, 95:1 planetary gearbox, (New) 10 HP Main Drive motor, (New) 5 hp backdrive motor, mounted plate w/ vibration Isolations. Mounted on approx. 4 stainless steel stand w/casters, safety guards, (New) programable logic control/drive panel. (Reconditioned with warranty)

MFR: Sharples

Buy Used 6" PFA Jacketed Column – Heat Transfer & Corrosion Protection

Used- 6" PFA lined column, jacketed.

MFR: Unknown

Used - Paint Media Mill, 8" x 30" Milling Chamber, 6 Gallon, 10 HP Motor

Used- Paint Media Mill. includes 8" diameter X 30" high milling chamber, approximate 6 gallon. Stainless Steel screening section, jacketed chamber. Driven by 10 HP, 220/440 V, 1740 RPM, 3-phase, 60 cycle motor. Previously used at paint processing facility and in working condition when removed from service. No Manufacturers Tag.

MFR: Unknown

Used Stewart Bolling 6" x 12" Pilot Two Roll Rubber Mixing Mill

Used Stewart Bolling 6" x 12" Pilot Scale Two Roll Mixing Mill With 5 HP Gear Motor. Designed for laboratory, pilot plant and small-batch processing of compatible rubber, plastic and polymer compounds. Features (2) chrome-cored rolls measuring approximately 6" diameter x 12" long, driven by a 5 HP single-speed gear motor with a fixed gear ratio. Equipped with two-point manual roll gap adjustment for controlling material thickness and split end guides for containing material within the working roll area. Safety features include front and rear knee-operated safety mechanisms and an over-the-roll safety cage. Electrical requirements are 220/440 volts, 3-phase, 60 Hz. Serial #2560. Possible applications include rubber compounding, polymer blending, plastic material processing, sheeting, mastication and mixing of compatible natural rubber, synthetic rubber, elastomers, thermoplastic compounds, pigments, fillers and other suitable rubber or polymer formulations.

MFR: Stewart Bolling

Farrel Rubber/Plastic Laboratory Calender Mill – Inverted "L" 4-Roll, Adjustable Knives

Used- Farrel 4-Roll Inverted "L" Rubber/Plastic Laboratory Calendar Mill. 6" D x 13" L rolls. 500 degrees F max. roll temp. Up to 35 RPM. Fixed center roll w/ adjustable bottom, top, and offset. Full herringbone even speed gears on one side, Full herringbone friction gears on the other side. Nylon adjustable infeed guides. (2) adjustable twin knives on bottom roll. Cable safeties on both sides of frames. SCR drive w/ dynamic braking; Operators control station with variable speeds. Variable speed 7.5 HP motor. 3/460V. Serial# 73A1499.

MFR: Farrell

Used Buflovak Atmospheric Double Drum Dryer | Model 6" x 8" ADDD | Pilot & R&D D

Used Buflovak Atmospheric Double Drum Dryer, Model 6" x 8" ADDD. 2 sq/ft Total drying surface area. Approximate 6" diameter x 8" face cored drum, rated 140-160 psig. Driven by a 1/2hp, 3/60/208-230/460 volt, 1725rpm motor through reducer 41.58:1 ratio. Blador VS drive. The dryer features twin chrome-plated drying drums with independent drum gap adjustment, stainless steel frame and safety guards, product feed trough with feed manifold, and doctor blade assembly. Compact unit is designed for drying slurries, purees, pastes, and other pumpable materials into flakes or powders and is well suited for R&D, product development, and small-scale production. Mounted on stainless steel frame. Job No. P1-00972, Serial# 2013-04, built 2013.

MFR: Buflovak

Industrial Used Belt O Matic Belt Dryer Model 320B – High-Efficiency Continuous Drying

Used Belt O Matic Belt Dryer, Model 320B. 6 5" wide by 245" long; 3 phase/480 Volt/40 Amps;LP/natural gas; 5-7 PSI pressure Range; 1,000,000 BTU rating; 10,000 maximum CFM; 7.5 HP fan, maximum drying air temperature 250 degrees F. Built 2017. Last ran wet coffee grounds.

MFR: Belt-O-Matic

Used Siemens EK1000-2 6.56 MW Steam Turbine Generator Plant

Used- Siemens 6.56 MW Steam Turbine Generator Plant, Model EK1000-2, Manufactured 1981. Siemens Model EK1000-2 multistage extraction/condensing steam turbine generator system, rated at 6,560 kW (6.56 MW) shaft output, manufactured in Germany in 1981, Serial No. T5719. Turbine designed for operation at 9,000 RPM with live steam pressure of 48.3 bar (700 PSI) at 404C (759F), intermediate steam extraction pressure of 7.3 bar (106 PSI), and condensing exhaust design pressure of 12 kPa absolute. Equipped with Siemens 6:1 speed reduction gearbox, rated at 6,900 kW continuous duty, reducing turbine speed from 9,000 RPM to 1,500 RPM. Driven generator is a Siemens Model 1DU7534-7FE82-Z three-phase synchronous alternator, Serial No. D8025106101, rated at 8,200 kVA, 11,000 volts, 50 Hz, 1,500 RPM, with 0.8 power factor. System includes associated excitation equipment, electrical control and protection panels, Siemens and GE protection components, SEL digital relays, DECS-250 digital excitation controller, lubrication system with approximately 6,300-liter oil reservoir, and (2) Alfa Laval Model M10-BDFG plate heat exchangers manufactured in 2021. Associated plant equipment includes main steam condenser and steam dump condenser, subject to confirmation of sale scope. Turbine and gearbox underwent extensive major inspection and maintenance in JulyAugust 2023, including rotor removal, internal inspections, non-destructive testing, rotor dynamic balancing, gearbox inspection, bearing inspection, generator electrical testing, and vibration assessment. Inspection records reported acceptable gearbox condition and low post-commissioning vibration levels at that time. Main condenser was retubed in 2012 and inspected in 2023. Originally installed as part of an industrial cogeneration and energy recovery system at a sulphuric acid production facility. Complete engineering documentation, maintenance records, mechanical drawings, electrical schematics, and inspection reports available.

Used Sweco LX60C168 60” Low Profile Screener – Single Deck, 3D Motion, Spare Motor & Springs, Built 2024

Used- Sweco Model LX60C168 60" Single Deck Low Profile Screener. The Sweco LX Low Profile Flow-Thru Separator allows for high capacity wet or dry scalping in a compact, low headroom design. Dual .69 hp motors mounted on opposite sides of the LX allow unrestricted flow of material and create the 3-D motion that allows oversize material full discharge, keeping the screen clear for maximum product flow. Low headroom requirements (as little as 15 inches) and straight flow design, allow the LX to fit easily into existing product lines without reworking the entire system. 12" center bottom outlet. Includes used spare motor, and six (6) spare springs. Unit is mounted on a 27" high base. No lid. " screen installed. 230-460/3/60-volt input. Serial# 554445-A-09/24, built 2024.

MFR: Sweco