Chemical Equipment

Used Hi Speed Disperser has two 50" stainless steel shafts with two 8" diameter blades on each. Unit is equipped with an air over oil lift. Variable speed. Driven by a 20 hp, 1755 rpm motor that re...

Used-Hi Speed Disperser has two 50" stainless steel shafts with two 8" diameter blades on each. Unit is equipped with an air over oil lift. Variable speed. Driven by a 20 hp, 1755 rpm motor that requires 230/460 vac, 3 ph electricity. Overall dimensions are approximately 32" w x 80" l x 80" h. Motor is tagged for hazardous location.

Buy Used Blue M POM-371A-2 Oven – 8.25 Cu Ft, Electrically Heated

Used- Blue M Model POM-371A-2 Oven. 8.25 Cubic feet capacity. Maximum temperature 212 degrees F (100 C). Stainless steel interior, inside dimensions measure 27" wide X 20" high X 24" deep. Electrically heated, rated for 208/240 Volts, Single phase, 60 Hz. B.O.M. NO. E3-00041. Serial# P20-312.

MFR: Blue M

Used Doyle and Roth Vertical Shell & Tube Heat Exchanger – 20.2 Sq Ft

Used- Doyle and Roth Vertical Shell and Tube Heat Exchanger, Approximate 20.2 Square Feet. Carbon steel shell rated 150 psi / FV at -20 to 200 degrees F. (27) .75" diameter x 48" long Hastelloy C-276 tubes rated 15 psi / FV at -20 to 300 degrees F. Openings: (1) 4", (2) 1", (3) .75". 40,025 BTU/H. Single pass. Baffle spacing 4.125". Side lug mounted. National Board# 20734, Serial# S1989-4, 2008. No bottom head.

MFR: Doyle & Roth

Doyle and Roth Vertical Shell and Tube Heat Exchanger. Used.

Used- Doyle and Roth Approximate 20.2 Square Feet Vertical Shell and Tube Heat Exchanger. Carbon steel shell rated 150 psi / FV at -20 to 200 degrees F. (27) .75" diameter x 48" long Hastelloy C-276 tubes rated 15 psi / FV at -20 to 300 degrees F. Openings: (1) 4", (2) 1", (3) .75". 40,025 BTU/H. Single pass. Baffle spacing 4.125". Side lug mounted. National Board# 20733, Serial# S1989-3, 2008. No bottom head.

MFR: Doyle & Roth

Doyle and Roth Shell & Tube Exchanger – 20.2 Sq Ft, Side Lug Mount

Used- Doyle and Roth Shell and Tube Vertical Heat Exchanger, Approximate 20.2 Square Feet. Carbon steel shell rated 150 psi / FV at -20 to 200 degrees F. (27) .75" diameter x 48" long Hastelloy C-276 tubes rated 15 psi / FV at -20 to 300 degrees F. Openings: (1) 4", (2) 1", (3) .75". 40,025 BTU/H. Single pass. Baffle spacing 4.125". Side lug mounted. National Board# 20732, Serial# S1989-2, 2008. No bottom head.

MFR: Doyle & Roth

Used Sargent single-pass continuous conveyor dryer. The dryer has a 3 heating zone system, each with an electric heat source. The first zone appears to have a 350° F maximum temperature and zones two...

Used-Sargent single-pass continuous conveyor dryer. The dryer has a 3 heating zone system, each with an electric heat source. The first zone appears to have a 350° F maximum temperature and zones two and three appear to have a 700° F maximum temperature based on the original drawing. The conveyor dyer has a 20.5" wide stainless steel perforated conveyor belt that passes through a 210" long x 78" wide x 85" tall tunnel. The tunnel has three side access doors. The dryer has a 6" diameter inlet that is 124" from ground level and a 6" diameter outlet that is 30" from the ground. Overall dimensions of the unit are 295" long x 78" wide x 147" tall with drives and motors. Serial # 2036. Built 1976.

MFR: Sargent-Welch

Used AB Process / JBT Mixing System | 200 Gallon Jacketed Skid-Mounted Mixer

Used AB Process / JBT Mixing System | 200 Gallon Jacketed Skid-Mounted Mixer. Jacket rated 150 PSI at 366 degrees F. 36" straight side x 41" diameter tank dimensions, cone bottom. Scrape agitator. 15 HP SPX product pump. On Mettler Toledo load cells. Mounted on skid Built 2018.

MFR: JBT Foodtech

Used Hamilton 200-Gallon Stainless Steel Agitated Kettle – 120 PSI Jacket

Used- Hamilton 200 Gallon Agitated Kettle, stainless steel construction with 3/4 jacket, rated for 120 PSI at 342 degrees F. Features top mounted full sweep agitator, currently less drive. Hinged lid top covers. Hemispherical bottom with 2-1/2" diameter center bottom outlet.

MFR: Hamilton

Used Carbon Steel Blower – 200 HP, 8" x 44" Housing, 12" x 36" Inlet

Used- Blower, Carbon Steel. Approximate 8" x 44" housing. Driven by a 200 HP, 460 Volt, 3570 RPM motor. 12" x 36" inlet, 8" x 16" outlet.

MFR: No

Used Werner & Pfleiderer UK17 Double Arm Mixer – 200 Gal, Stainless Steel Clad, Jacketed

Used- Werner & Pfleiderer Double Arm Mixer, Model UK17, Stainless Steel Clad 200 Gallon. Sigma tangential blades, jacketed bowl (bottom only) 43" front-back x 53" left-right x approximately 36" deep. Geared both ends. Set up for hydraulic tilt 7.5 hp, 220/440V, 1750 rpm. No base, no drive. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.

MFR: Werner & Pfleiderer

Used Howard 200 Gallon Double Arm Mixer – 304 Stainless Steel, Hydraulic Tilt

Used- Howard Double Arm Mixer, Approximate 200 Gallon, 304 Stainless Steel. Non-jacketed bowl approximate 50" left to right x 44-1/8" front to back x 34-1/2" deep. Overlapping sigma blades set up for hydraulic drive, no power pack. Dual ram hydraulic tilt, top safety grate. Mounted on a stainless steel frame. Serial# H3649-2, built 2001.

MFR: Howard

Used 600 HP Schutte-Buffalo Hammermill with Twin City Blower, Heavy-Duty

Used- Schutte-Buffalo-Astec Model AHM-20 Carbon Steel Hammermill. Approximate 48" diameter x 50" wide rotor. Top feed with hopper, bottom discharge. Driven by a 600 HP, 3/60/460 volt, 1790 rpm motor. Mounted on a frame. Serial# 16088HM1. Includes a Twin City blower, Type RBR-SW, size 926, driven by a 200 HP, 3/60/230/460 volt, 1785 rpm motor. Astec serial# 16088HM1.

MFR: Schutte