Chemical Equipment
Stock No.:
10128086Used 1,900 Gallon JV Northwest Stainless Steel Jacketed Tank with 3 HP Agitator – 45 PSI, UM Stamped
Used 1,900 Gallon JV Northwest Stainless Steel Jacketed Tank with 3 HP Agitator 45 PSI, UM Stamped, Serial # 13847, Built 1997. Jacket in two sections is rated for 45 PSI @ 400 degree F. Tank is 78" diameter x 84" straight side. Bottom and 1/3 of the straight side jacketed. Tank has bottom mounted 3 hp agitator, 230/460 vac 3 ph power required. Top has 20" round manway with hinged lid, 10" vent pipe, one 6" tri clamp, two 3" tri clamp, and one 2" tri clamp. Jackets have two threaded connections each. Bottom has 4" 90 degree tri clamp elbow for the discharge. Side has .75" coupling with probe. Unit has four carbon steel legs.
MFR: JV Northwest
Stock No.:
51258018Used Strong Scott Stainless Steel Double Spiral Ribbon Blender, Model IMXS, 193 Cu Ft, 50 HP XP
Used Strong Scott Stainless Steel Double Spiral Ribbon Blender, Model IMXS, size 50.12-6. Approximate 193 cubic foot capacity. With top cover and bag dump station. 50 HP XP motor & reducer. Center bottom outlet with rotary valve. Serial# 2817.
MFR: Strong Scott
Stock No.:
10715045IN STOCK and New- Paul O. Abbe Model RB-195 Ribbon Blender.
NEW & IN STOCK- Paul O. Abbe Model RB-195 Ribbon Blender. In -Stock .195 Cubic Foot working capacity. 220 Cubic Foot total volume. Type 304 stainless steel polished. Food grade. All stainless steel construction. Trough dimensions: Approximately 56.7" wide x 118.2" long x 62.6" deep. Internal double spiral ribbon. Packing glands and pillow block bearings. 60 hp SEW Euro drive hollow bore design. 230/460 volt, 1775 rpm, 3/60 with approximately output 29 rpm. Top cover with hold down clamps and limit switch. Center Loading cover with welded safety grate, 30" wide x 50" long. Approximate 4.7" wide x 19.7" flush air operated plug valve. Discharge housing is approximate 20.5" wide x 28.4" long. Approximately 4" discharge height. Approximate weight 11,660 pounds. Approximate overall dimensions: 76.4" wide x 183" long x 93.8" high. Controls are available upon request.
MFR: Paul O Abbe
Stock No.:
44284Used Alpine Ultraplex Cross Flow Mill B1000UP – 195 HP, Carbon Steel, Industrial Grinder
Used- Alpine "Ultraplex" Cross Flow Mill, Type B1000UP. Material of construction is Carbon Steel. Cast iron housing with swing back door. Top feed but without feed hopper. Baffle ribbed grinding tracks. Belt driven by a 195 hp (130 kw)-380volt/50cycle/3ph motor. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.
MFR: Alpine
Stock No.:
10151501Alloy Fabricators Approximately 1,950 Gallon Mix Tank with Internal Coils
Used- Alloy Fabricators Approximately 1,950 Gallon Mix Tank with Internal Coils. 304 Stainless Steel Jacketed. 78" diameter x 81" straight side; Dished top and bottom; Internal rated 15/FV at 335 degrees F; Jacket rated 44 psi at 335 degrees F; Coils rated 44 psi at 335 degrees F; (4) side wall baffles; 7.5 hp axial type agitator, 304 stainless steel, Foam breaker at top - 2 blade, 51" dia; dual hub with 3 blades - upper 50" dia; lower 30" dia, 18" dia. 2 blade radial flow at bottom. Serial # 1-151A; Built 1991.
MFR: Alloy & Steel Fab
Stock No.:
54110002Used Doyle & Roth Shell & Tube Heat Exchanger | 1963 Sq. Ft. | Alloy 400 Tubes | 300 PSI | 2006/2018
Used Doyle & Roth Shell & Tube Heat Exchanger | 1963 Sq. Ft. | Alloy 400 Tubes | 300 PSI | 2006/2018. Monel/Alloy 400 tube side construction. Full vac/300 psig shell side design pressure; 390 psig shell side test pressure; 650/15 degrees F shell side max./min. design temp.; 1 pass shell side. Full vac/250 psig tube side design pressure; 325 psig tube side test pressure; 650/15 degrees F tube side max./min. design temp.; 3 pass shell side. OAD: 32" D x approx. 248" L. (300) 1.25" D x 240" L tubes. Built 2006, Repaired by Ohmstede in 2018. NB #20179. Original SN S-1443-4, new SN 824114.
MFR: Doyle & Roth
Stock No.:
10151644Used Patterson-Kelley 2 Cu. Ft. Stainless Steel Twin Shell V-Blender – 60 Lb./Cu. Ft. Density Rating
Used- Patterson-Kelley approximately 2 cubic foot stainless steel Twin Shell V-Blender. Rated for a maximum material density of 60 lbs. per cubic foot. Unit has provision for an intensifier bar; intensifier bar is not included. Model: Twin Shell Dry Blender.
MFR: Patterson Kelley
Stock No.:
10151645Used Patterson-Kelley 2 Cu. Ft. 316 Stainless Steel V-Blender – 270 Lb./Cu. Ft. Rating with Intensifier Bar
Used- Patterson-Kelley approximately 2 cubic foot Twin Shell V-Blender constructed of 316 stainless steel. Rated for a maximum material density of 270 lbs. per cubic foot. Equipped with an intensifier bar for enhanced mixing and dispersion. Unit is mounted on a stainless steel frame with casters for portability.
MFR: Patterson Kelley
Stock No.:
11059409Used Patterson-Kelley 2 Cu. Ft. Sanitary Stainless Steel V-Blender – Pharmaceutical Finish, 25 RPM with Dispersion Bar Provision
Used- Patterson Kelly 2 Cu.Ft. Twin Shell V Blender. Sanitary, Stainless Steel with Pharmaceutical grade finish. Rated 60 Lbs./Cu.Ft. material density. Unit has provisions for Liquid/Solids dispersion Bar. (No Bar installed) Shell has chain driven 3/4 HP, 208-220/440 volt with gear reducer for 25 RPM output. Bar drive is 2 HP with belts and guard. 6" Discharge with butterfly valve. 37" floor clearance. 14" charging ports with removable vented covers. Last use was pharmaceutical.
MFR: Patterson Kelley
Stock No.:
53011006High-Efficiency APV Crepaco W20/20 Pump – 105 GPM, 3500 RPM
High-Efficiency APV Crepaco W20/20 Pump 105 GPM, 3500 RPM. Approximate 105 gallons per minute, 95 head feet @ 3500 rpm. Approximate 2" inlet, 2" outlet. Driven by a 5hp, 3/60/230/460 volt, 3500 rpm motor. Serial# H-9296-95.
MFR: APV/Crepaco
Stock No.:
53011009APV Crepaco Unused W20/20 Stainless Steel Pump – 105 GPM, 95 Head Feet
APV Crepaco Unused W20/20 Stainless Steel Pump 105 GPM, 95 Head Feet. Approximate 105 gallons per minute, 95 head feet @ 3500 rpm. Approximate 2" inlet, 2" outlet. Driven by a 3hp, 3/60/230/460 volt, 3520 rpm motor. Serial# H-9317.
MFR: APV/Crepaco
Stock No.:
53011010Unused APV Crepaco W20/20 Centrifugal Pump – 5HP Motor
Unused APV Crepaco W20/20 Stainless Centrifugal Pump 5HP Motor. Approximate 105 gallons per minute, 95 head feet @ 3500 rpm. Approximate 2" inlet, 2" outlet. Driven by a 3hp, 3/60/230/460 volt, 3520 rpm motor. Serial# H-9318.
MFR: APV/Crepaco
