Adhesive and Sealant Equipment

Used Thermo Scientific Series 2 Water Jacketed CO2 Incubator – 184L (6.5 cu. Ft.) Capacity

Used- Thermo Scientific Series 2 Water Jacketed C02 Incubator, 184L (6.5 cu. Ft.) Capacity. Inside Glass door, 21-1/2" wide x 27" tall x 19-1/2" deep stainless steel chamber. Temperature range 5C above ambient up to 55C (131F)

MFR: Thermo Scientific

Used Thermo Revco Upright Refrigerator, Model REL3004A21, 29.2 Cu ft capacity

Used- Thermo Revco Upright Refrigerator, Model REL3004A21. 12oz charge of R-134A Refrigerant. 29.2 Cu ft capacity, 1 to 8 Degrees C Temperature Range. Approximately 29" wide x 53" tall x 26" deep chamber, with (3) 29" wide x 26" deep wire shelves. 115V, 60hz power requirements. Serial# P14R-119636-PR

MFR: Thermo Scientific

Used Travaini TRHE 32-45/C/RZ Liquid Ring Vacuum Pump – CO2 Roughing Pump System with Intervac Booster

Used- Travaini Liquid Ring Vacuum Pump, Model TRHE 32-45/C/RZ. Rated 28.8" vacuum at 11 cfm. 3 HP, 3450 RPM, 3/60/230/460V motor. With Fenwal Thermostat and Model PLT3206/5CGF Intervac pump. Approx. OAD: 60" L x 40" W x 70" H. Located 2629 Seventh Street Berkeley CA 94710; Can load; $4,000 PRD; Seller is working on getting us a video; Can accommodate inspection; no docs; was previously used as "CO2 Vacuum Roughing Pump"

MFR: Travaini

Used Thermatool Tube Cutting Machine - 2”-4.5” OD, ABB Drives, Scrap Conveyors

Used- Thermatool Tube Cut-Off Machine. OD Range: 2"-4.5", Max Wall Diameter: .235". Max Speed 250 FPM, Hydraulic Accelerator Hydraulic Clutch, Encoder, Two Scrap Goose Neck Conveyors Unico Controller, ABB Drives, spare cut off die.

Used Ultrasonic Systems Prism 400 Spray Coater – 400mm x 400mm | 600mm/s | Tilt & Rotation | Built 2023

Used- Ultrasonic Systems Spray Coater, Model Prism 400. 600mm/second (20"/sec) coating speed; 400mm x 400mm x 125mm (15.75" x 15.75" x 4.72") application area; Up to 45 degrees in two directions tilt motion; 0-90 or 0-180 degree theta rotation range; Lead screw, stepper drive Z motion; Precision ball screw X/Y platform; 16" max. X and Y axis stroke; 0-150 degrees C (32-302 degrees F) heat plate set point, configurable up to 200 degrees C (392 degrees F). With stand. 1/50-60/220V. Built 2023.

MFR: Ultrasonic

Buy Used Vac-U-Max VPU-S-3T Vacuum Conveyor – Industrial Bulk Material Handling

Used- Vac-U-Max Model VPU-S-3T Positive Displacement Vacuum Conveying System with Sutorbilt 3 HP blower. Rated approximate 51 CFM @ 12" HG. Driven by a 3 HP, 230/460 volts, 3-phase, 60 Hz, 1730 RPM motor. Includes 2" diameter NPT inlet & outlet with 2 silencers. Mounted on carbon steel frame.

MFR: Vacumax

Pre-Owned VanKel VK 7010 Apparatus – 8 Spindles, VK 8000 Sampler

Used- VanKel Lab Equipment, Model 10-0700. VK 7010 apparatus set up for 8 (4+4) spindles, (8) 3-1/2" diameter vessels (requires both spindles and vessels). With VK 8000 Automatic Sampling Station can handle 1/2" diameter vials. VK 806 Syringe Pump, (2) VK 750D Heater Circulators, water range from Ambient to 55 degrees Celsius, range of +/- 0.1 Degree C. Includes BIO-DIS Reciprocating Cylinder Apparatus temp range from 5 to 40 Degrees C. 5-60 dips per minute.

Used OMAX Maxiem 1530 Waterjet Cutter – 52" x 122" Table | 30 HP Pump | 50,000 PSI | CNC Control

Used- OMax Maxiem Waterjet Cutting System; Model 1530; Cutting Area 52" X 10 Table Size 58" X 122" Z-Axis Travel 6" Intensifier Output 50,000 PSI Motor Size 30 HP; Equipped with OMax PC Based CNC Control; Omax M30 Direct Drive Pump; 500 Lb Abrasive Hopper; dual Side Drive Precision Rack & Pinion; Abrasive Hopper Settling Tank;

Used Omax 80X Precision Waterjet Cutting System | CNC Industrial Waterjet Cutter

Used- Omax Precision Waterjet Cutting System, Model 80X. Cutting Area 13' 4'' long x 6' 8'' wide. Table size 15' long x 7' 5'' wide. Speeds up to 180" min. Repeatability within 0.001''. Includes Garner sand tank and control cabinet. Serial # K511537.

Used Kulicke & Soffa Asterion Wedge Bonding Machine – Advanced Precision (Built 2023)

Used- Kulicke and Soffa Wedge Bonding Machine, Model Asterion. 300mm x 300mm bondable area. 0.1 um X and Y axes; 0.1 um Z-axis, 50mm Z-stroke; +/- 220 degree theta axis, .0057 degree theta axis resolution. 710mm D x 225mm H material handler bay size w/o insert, 710mm D x 460mm H open bay size. GS4 Pattern Recognition vision system. 1/50-60hZ/200-240V. Built 2023.

Used Pro Fusion Welding Lathe PFL-1216-37 – 36" Center to Center | TSS-2 Sharpshooter Included

Used- Pro Fusion Custom Welding Lathe, Model PFL-1216-37. Made to be 36" center to center instead of the stock 16" with TSS-2 Sharpshooter tungsten sharpener set

Unused Zeiss O-Inspect 3/2/2 CMM – 300 x 200 x 200 mm | Optical + Tactile Sensors | Calypso Software | Built 2022

Used- Zeiss CMM, Model O-Inspect 3/2/2. 300 x 200 x 200 mm3 measuring volume; Zeiss Calypso software; Zeiss Discovery v.12 2D optical camera sensor; Zeiss Vast XXT tactile sensor. Built 2022. Reported to be unused. Our freight specialists can assist you with door to door transportation and all customs documents needed to make the process go as smoothly as possible.