Adhesive and Sealant Equipment
Stock No.:
52862012Doyle and Roth Vertical Shell and Tube Heat Exchanger. Used.
Used- Doyle and Roth Approximate 20.2 Square Feet Vertical Shell and Tube Heat Exchanger. Carbon steel shell rated 150 psi / FV at -20 to 200 degrees F. (27) .75" diameter x 48" long Hastelloy C-276 tubes rated 15 psi / FV at -20 to 300 degrees F. Openings: (1) 4", (2) 1", (3) .75". 40,025 BTU/H. Single pass. Baffle spacing 4.125". Side lug mounted. National Board# 20733, Serial# S1989-3, 2008. No bottom head.
MFR: Doyle & Roth
Stock No.:
52862013Doyle and Roth Shell & Tube Exchanger – 20.2 Sq Ft, Side Lug Mount
Used- Doyle and Roth Shell and Tube Vertical Heat Exchanger, Approximate 20.2 Square Feet. Carbon steel shell rated 150 psi / FV at -20 to 200 degrees F. (27) .75" diameter x 48" long Hastelloy C-276 tubes rated 15 psi / FV at -20 to 300 degrees F. Openings: (1) 4", (2) 1", (3) .75". 40,025 BTU/H. Single pass. Baffle spacing 4.125". Side lug mounted. National Board# 20732, Serial# S1989-2, 2008. No bottom head.
MFR: Doyle & Roth
Stock No.:
54687081Used Sargent single-pass continuous conveyor dryer. The dryer has a 3 heating zone system, each with an electric heat source. The first zone appears to have a 350° F maximum temperature and zones two...
Used-Sargent single-pass continuous conveyor dryer. The dryer has a 3 heating zone system, each with an electric heat source. The first zone appears to have a 350° F maximum temperature and zones two and three appear to have a 700° F maximum temperature based on the original drawing. The conveyor dyer has a 20.5" wide stainless steel perforated conveyor belt that passes through a 210" long x 78" wide x 85" tall tunnel. The tunnel has three side access doors. The dryer has a 6" diameter inlet that is 124" from ground level and a 6" diameter outlet that is 30" from the ground. Overall dimensions of the unit are 295" long x 78" wide x 147" tall with drives and motors. Serial # 2036. Built 1976.
MFR: Sargent-Welch
Stock No.:
10986027Used AB Process / JBT Mixing System | 200 Gallon Jacketed Skid-Mounted Mixer
Used AB Process / JBT Mixing System | 200 Gallon Jacketed Skid-Mounted Mixer. Jacket rated 150 PSI at 366 degrees F. 36" straight side x 41" diameter tank dimensions, cone bottom. Scrape agitator. 15 HP SPX product pump. On Mettler Toledo load cells. Mounted on skid Built 2018.
MFR: JBT Foodtech
Stock No.:
11252214Used Hamilton 200-Gallon Stainless Steel Agitated Kettle – 120 PSI Jacket
Used- Hamilton 200 Gallon Agitated Kettle, stainless steel construction with 3/4 jacket, rated for 120 PSI at 342 degrees F. Features top mounted full sweep agitator, currently less drive. Hinged lid top covers. Hemispherical bottom with 2-1/2" diameter center bottom outlet.
MFR: Hamilton
Stock No.:
42467005Used Carbon Steel Blower – 200 HP, 8" x 44" Housing, 12" x 36" Inlet
Used- Blower, Carbon Steel. Approximate 8" x 44" housing. Driven by a 200 HP, 460 Volt, 3570 RPM motor. 12" x 36" inlet, 8" x 16" outlet.
MFR: No
Stock No.:
52905003Hamilton 200 Gallon Triple Motion Stainless Steel Kettle
Used- Hamilton 200 Gallon Triple Motion Stainless Steel Kettle. 48" dia x 36" deep. Hemispherical bottom. Side/bottom scrape triple agitation with pivoting bridge. Jacket rated 125 PSI @ 345 Deg F. 5HP drive, 3/50/60/230/460V. Split stainless lids. 3" Tri-Clamp discharge fitting. Serial# 2475, National Board# A8223. Last used in food.
MFR: Hamilton
Stock No.:
54280002Used 200 Gallon Stainless Steel Vertical Mix Tank – Propeller Agitated, Leg Moun
Used 200 Gallon Mix Tank, Stainless Steel, Vertical. Approximately 48" diameter, 24" straight side. Flat top (with cover), Dished bottom. Clamp-on Top entering 3-blade propeller-style agitator, driven by a 3/4hp, 3/60/208-230/460 volt, 1725rpm washguard motor. Opening Top: 2", 2-1/2" diameter. 2" Center bottom outlet with 14" discharge height. Mounted on (3) stainless steel legs. No Manufacturer Tag.
MFR: Unknown
Stock No.:
54687049Used Paul Mueller 200 gallon 304 stainless steel Reactor. Serial # P11720-14. National Board # 9905. Internal is rated for 50 psi @ 450 f. The jacket is rated a 150 psi @ 450 f with a glycol medi...
Used-Paul Mueller 200 gallon 304 stainless steel Reactor. Serial # P11720-14. National Board # 9905. Internal is rated for 50 psi @ 450 f. The jacket is rated a 150 psi @ 450 f with a glycol medium. Shell is also rated for full Vacuum. The tank is 36" in diameter with 32" straight side height and 8" dish bottom and dome top. Agitator is a 3 blade prop type with a 200 rpm Philadelphia 1 hp motor drive. The top has a 18" manway cover with pnuematic assist and glass view port. Top also has (3) 2" sanitary fittings, (3) 3" sanitary fittings and a 6 flange fitting with a glass view port. The bottom has a 2" sanitary center discharge. The side has 3" flange fittings (currently covered with a blind flange). Requires 230 vac 3 ph electrical supply. Built in 1984. Good Condition.
MFR: Paul Mueller
Stock No.:
54687050Used Paul Mueller 200 gallon 304 stainless steel Reactor. Serial # P11720-15. National Board # 9906 Interior is rated for 50 psi @ 450 f. The shell is rated a 150 psi @ 450 f with a glycol medium. S...
Used-Paul Mueller 200 gallon 304 stainless steel Reactor. Serial # P11720-15. National Board # 9906 Interior is rated for 50 psi @ 450 f. The shell is rated a 150 psi @ 450 f with a glycol medium. Shell is also rated for full Vacuum. The tank is 36" in diameter with 32" straight side height and 8" dish bottom and dome top. Agitator is a 3 blade prop type with a 200 rpm Philadelphia 1 hp motor drive. The top has a 18" manway cover with pnuematic assist and glass view port. Top also has (3) 2" sanitary fittings, (3) 3" sanitary fittings and a 4" flange fitting with a glass view port. The bottom has a 2" sanitary center discharge. The side has 3" flange fittings (currently covered with blind flange). Requires 230 vac 3 ph electrical supply. Built in 1984. Good Condition.
MFR: Paul Mueller
Stock No.:
54687061Used National Turbine 7 stage centrifugal blower. According to the curve it can blow 3,000 cfm @10 psi, 4,000 cfm @ 8.5 psi. Model # NT88307-5-00-2-AD. Serial # 2111020. Driven by 200 hp electric m...
Used-National Turbine 7 stage centrifugal blower. According to the curve it can blow 3,000 cfm @10 psi, 4,000 cfm @ 8.5 psi. Model # NT88307-5-00-2-AD. Serial # 2111020. Driven by 200 hp electric motor. Blower has 8" air intake and 8" export ports. Requires 460 vac 3ph electrical supply. Overall dimensions 40" wide x 83" tall x 100" tall. Curve on file.
