Used Water Treatment Equipment

Stock# 50628001

Used- Ultrafiltration Hollow Fiber Module Water Treatment Plant. 0.5 MGD Skid Mounted, 700 gpm, 1,100 gallons Feed/CIP Tank Off Skid, Feed Pump with VFD, 300 Micorn Pre-Membrane Strainer, 1,100 gallons RF Tank Off Skid, RF Pump with VFD, Control Panel. Built, 2013.

Stock# 51047020

Unused- Enereau Systems Membrane BioReactor Water Treatment System. Custom Build. Size: maximum 220 m3/day throughput while returning usable water to the facility. Temperature range 10-50 Degrees C. This system includes (2) FRP Tanks with transfer pumps, aeration pump, lift station with pumps, permeate skid with pumps, blower, PLC, and control panel. No membrane tanks. Built 2019.

Stock# 51818003

Used- Barnstead International Electrically Heated Portable Still, Model A1007. Output flow rate capacity 0.5 gallon per minute (1.9 LPH). Cooling flow rate 4 gallons per hour. 1.4 kW heater. Approximate 6" diameter x 12" straight side with sheathing. Mounted on carbon steel frame. UL Listed. Serial# 919031256004. 1/60/120 Volt, 12 Amps.

Stock# 51056006

Unused- Toro/Watropur Waste Water Sludge Drying System. Includes: (1) Toro Sludge Conveyor, Stainless steel, 215mm/6700mm /304mm, Capacity 307.9-618.1 gallon/hour (1.4 - 2.81 M3/hour) 2.5 Kw motor, (1) Toro Sludge Conveyor, Stainless steel, 160mm/10550mm/304mm, 1.1 kw - 127.6-255.16 gallon/hour (0.58 - 1.16 m3/hour). (2) Watropur Sludge Conveyor, type WSC 4.6, Stainless steel, 95 degree F (35 degree C), 2.2 Kw motor, 70% dried solids (Screw conveyors). (1) Sludge drying system includes: (2) Watropur Bunkers, capacity 1231.83 gallon (5.6 M3), material of construction hot galvanized carbon steel includes bunker with parallel progressive spiral screw conveyor bottom, platform and ladder, (1) Watropur Belt sludge dryers, type TLG3000B-WTR1400, temperature sludge/ambient 50-104 degree F. (10 - 40 degree C), Sludge inlet dried solid content: 20,0% D.S. to 90% D.S, Evaporative capacity per day 6600 pounds (3000 kgs)/day water, Power absorbed/installed 40/50 kW/hour (50 Hz). Overall dimensions 124" (4130 mm) long x 62" (1935 mm) width x 65" (1990 mm) high (Dryer). (1) Dosing pump system includes (9) Grundfos dosing pumps, (1) FRP Tank 330 gallon (1250 liter) with mixing device (unused still on wooden platform).

Stock# 51238001

Used- Bosch PharmaTec, Type Distille 1000-S6V 6 Stage Multi Pressure Distillation Unit. For infusion liquids with a capacity of 280.4-542.3 gallon/hour (1060-2050 liter/hour). Designed to produce sterile, non-pyrogenic water for injection (WFI). (6) Columns/shell-and-tube heat exchangers 27.5-gallon (104 liter) tube capacity. Inside rated for 150 psi (10 bar) and full vacuum (-1) at 32-392 degree F (0-200 degree C). Test pressure 276 psi (18.6 bar). System operation pressure: 90 psi (6 bar). Heating steam pressure: 135 psi (9 bar). Cooling water pressure: 90 psi (6 bar). Compressed air: 90 psi (6 bar). Only the first column of the distillation unit needs to be heated with plant steam. Control panel with Siemens S7-300 PLC and touch screen panel. Complete with pumps, valves, and additional pipe infrastructure. Frame/Skid mounted in 3 sections. On leg. Serial # 1.473. Overall dimensions: 134" (100 mm) long x 39" (1200 mm) width x 146" (4485 mm) high. Weight: 3 tonnes. Previous used in a Pharma application on infusion liquid food for hospitals.

Stock# 52436001

Used-Met-Chem 20 GPM Clarifier Skid. Includes: Parkson style 20 gpm clarifier with plastic plates; 1.3 x 3 cubic foot filter pres, (7x19) 470mm filter press plates, manual hydraulic closure; 200 gallon plastic holding tank with stand; 375 gallon mix tank with mixer; Polymer blend tank; Diaphragm and (3) metering pumps. Skid measures 8' wide x 19' long x 10' tall. Serial# 2697-R

Stock# 50161001

Used- Krofta Supracell Dissolved Air Flotation Clarifier, Model SPC-10 SRJ, 304 Stainless Steel. 120" Diameter x 23-1/2" deep tank. Raw inlet flowrate 250 gallons per minute maximum. Top mounted carriage assembly with drive, top scoop with drive, bottom flocculator distribution rake. 4" Inlet, 3" floated sludge outlet, 6" clarified treated water discharge, 4" DAF sediment outlet. Job # PN04-101. Built 2004. Unit includes (1) Griswold pump, (1) Nikuni pump and (1) Control panel, and miscellaneous drives.

Stock# 45141006

Used- WHE Performance Speration Systems filter. Stainless Steel. Driven by a 25 hp motor. No mfg. tag. ** SALE SUBJECT TO SELLER'S APPROVAL **

Stock# 52498001

Used-PCI Wedeco Environmental Technologies, Model PDSD-650 Ozone Generator with controls and switchgear. 12 each EIM Motor Operators for valves. 1 ea Instrument air skid, 2 compressors dryers.

Stock# 52498002

Used-PCI Wedeco Environmental Technologies, Model PDSD-650 Ozone Generator with controls and switchgear. 12 each EIM Motor Operators for valves. 1 ea Instrument air skid, 2 compressors dryers.

Stock# 50467019

Used- Ionics Life Sciences RO system with (3) Koch membrane filters, 4" diameter x 48" long, Koch Model 4040, dual UV light units, 3 hp Grundfos pump, system Serial # 06-00-62776.

Stock# 51694001

Used-Reverse Osmosis GE Osmonics 159 GPM RO System, Osmosis Water System, Model: 54A-HR(CA)169K-DLX, Voltage: 480 VAC, 60Hz.Note: RO system with stainless steel frame and control enclosure. Includes pre-filters and pumps. System previously used to purify water for a bottled water application. Permeate Rate 159 GPM. Concreate Rate- 45GPM. Pressure Max- 590PSIG (pump). Pressure Min. - 320PSIG (pump). (1) 75HP Motor with one Tonkaflow pumps, Model-SS24016KE. (1) 15Hp motor with two Tonkaflow Pumps Model-SS24002D.

Stock# 51056002

Used- Toro Waste Water Pre-Treatment System. Consisting of: (1) Toro Rotostrainer, type TR63/90. Material of construction is 304 stainless steel. Rated approximate 550.40 gallons per minute. Drum approximate 24-3/4" diameter x 35-3/8" wide. Opening 3 mm, capacity 27496.2 gallon per hour (125 M3/Hour) flow. (1) Tank capacity 52.9 gallon (200 liters), (1) Axial ventilator, 0.75KW, (1) Electrical heater. Includes controls Allen Bradley VFD 0.75 kW, 3" Magnetic Flowmeter -PVT, Composite sampler (Sigma SD900 WARS), Transmitter (CM442)- E&H, Ph electrode (CPF81D)- E&H and additional infrastructure. New 2016. Mounted inside a 20' container.

Stock# 52243001

Used-JWCE - IPEC Model IFM 60144P Internally Fed Rotary Screen, 304 stainless steel construction. 60" diameter by 144" long, perforated screen drum; 3mm screen perforations; headbox tank assembly, extending 2/3 the length of the drum, in 3/16" plate, c/w flanged inlet; 30" inlet connection c/w 304 stainless steel ANSI flange; 36" outlet connection c/w 304 stainless steel ANSI flange; splash guards in 10 gauge plate; integral drainage pan in 11 gauge construction; integrated solids discharge chute in 11 gauge construction; shaft mounted, 10" diameter by 3-1/2" wide UHMW polyurethane, roll wheels, supported by trunnion bearing assembly; external spray bar 2" Sch.40, 304 stainless steel pipe c/w 47 fan jet spray nozzles (1 USGPM per nozzle @ 40 psi), NC Class 1 Div 1 solenoid valve, PRV, ball valve, pressure gauge, manifold and hinged splash cover; #80 stainless steel roller chain, stainless steel driven sprocket and drive sprocket; helical gear drive c/w 2 hp, TEFC EX Class 1 Div 1 motor, 460V/3Ph/60Hz (additional voltages and classifications available, additional cost may apply); c/w epoxy coating to wetted internal parts; odor vent flange; 6 support stand. Includes: One (1) only Control Panel / MCC to operate JWCE- IPEC Model IFM 60144, NEMA 4X enclosure; stainless steel panel box c/w hinge; 30 amp, fused main disconnect; 150 Va controltransformer, 460 - 115; one (1) IEC motor contactor c/w overload; operator switch for: E stop, control power, hand/off/auto switches for screen; two (2) sequencing timers for operating motors and valves; dry contacts for system start, alarms and run status.

Stock# 52243002

Used-JWCE - IPEC Model IFM 6096P Internally Fed Rotary Screen, 304 stainless steel construction. 60" diameter by 96" long, perforated screen drum; 3mm screen perforations; headbox tank assembly, extending 2/3 the length of the drum, in 3/16" plate, c/w flanged inlet; housing in 10 gauge plate; 24" inlet connection c/w 304 stainless steel ANSI flange; 30"outlet connection c/w 304 stainless steel ANSI flange; splash guards in 11 gauge plate; integral drainage pan in 11 gauge construction; integrated solids discharge chute in 11 gauge construction; fully enclosed, cover panels in 11 gauge plate; 10" diameter by 3" wide, UHMW polyurethane, roll wheels, with 40MM double roll ball bearings; housing covers in 12 gauge construction; external spray bar, 2" SCH 40, 304 stainless steel c/w 31 fan jet, spray nozzles (1 USGPM per nozzle @ 40 psi), NC Class 1 Div 1 solenoid valve, PRV, ball valve, pressure gauge, manifold and hinged splash cover; #80 stainless steel roller chain, stainless steel driven sprocket and drive sprocket; helical gear drive c/w 2 hp, TEFC EX Class 1 Div 1 motor, 460V/3Ph/60Hz (additional voltages and classifications available, additional cost may apply); c/w epoxy coating to wetted internal parts; odor vent flange; 6 support stand. Includes: One (1) only Control Panel / MCC to operate JWCE- IPEC Model IFM 6096; NEMA 4X enclosure; stainless steel panel box c/w hinged door. 30 amp, fused main disconnect; 150 Va control transformer, 460 - 115; one (1) IEC motor contactor c/w overload; operator switch for: E stop, control power, hand/off/auto switches for screen; two (2) sequencing timers for operating motors and valves; dry contacts for system start, alarms and run status.

Stock# 51056004

Used- Alfa Laval Waste Water Sludge Thickener System. Consisting of: (1) Alfa Laval sludge thickener, Type Aldrum mini. Material of construction is AISI 304 stainless steel, capacity 1320 pounds DS/day (600 kgs DS/day), Floculator, Type IEC SK71S/4 TF 0.25KW, 13.7" (350 mm) diameter x 48.4" (1240 mm) high. (1) POLYMORE Polymer preparation system, Type mini 3-0,6, Capacity 0.16 gallon (0.6 liter) concentrated polymer/hour and maximum flow of 47.6 gallon (180 liters) water including mixing chamber with a built in agitator including valves, flow meter, a flow switch and a control cabinet with a built in pump, (1) KSB Dry Centrifugal Pump system 39594.5 gallon/hr. (180m3/hour), Mono screw pump system consisting of (1) 439.94 gallon/2m3/[email protected] m, (2) 8m3/[email protected] m (C14KC51RMA)- VFD includes Electrical Heater, Axial ventilator, 0.75 KW, and additional infrastructure. Mounted inside a 20' container.

Stock# 51879002

Used- Paul Mueller Co. Pure Steam Generator. Model PSG-7310, Serial # 370287 (2007). Produces Sterile Steam for Disinfection, Capacity: 900 Kg / Hour Rising Film Evaporator Centrifugal Separation Process.

Stock# 11453375

Used- Finn Aqua Pure Steam Generator, Model 1500-S-1. Single still with pump.

Stock# 11453376

Used- Finn Aqua Pure Steam Generator, Model 300S1, Stainless Steel Construction. Single effect with 2 hp Grundfos vertical pump and controls.

Stock# 52031001

Used- (2) Porex Filtration Tubular Membrane Filtration Systems; 2 Trains; 12 Modules per Train; Total active area 1098 square feet; 61 tubes per module; Nominal tube ID 0.5"; Pore Size 0.05 µ; Module Part number MME2005661VP; Module surface area 45.75 square feet; Mfg. 2020.

Stock# 43567019

Used- Millipore Ultra Filtration System, Type MSP 006145. Consisting of: (1) Mavag Reactor, 200 Liter (52.85 Gallon), 316L stainless steel. Internal rated -1/3.2 bar (-14.50/46.4 psi) at -10 to 130 degrees C.(14 to 266 F.), jacket rated 6/-1 bar (87/-14.50 psi) at -10 to 130 degrees C.(14 to 266 F.). Top entering agitator, (1) Mavag pressure tank, 100 liter (26.42 gallon), 316 L stainless steel. Internal rated -1/3 bar (-14.50/43.5 psi) at -10 to 130 degrees C.(14 to 266 F.), (1) Hanag reactor, 400 liter (105.70 gallon), 316L stainless steel. Internal rated -1/3.2 bar (-14.50/46.4 psi) at -10 to 130 degrees C.(14 to 266 F.), jacket rated 6/-1 bar (87/-14.50 psi) at -10 to 130 degrees C.(14 to 266 F.). Bottom entering agitator. (2) Millipore Prostak fixed end plate filter, model PSKPUFEP-1. (1) Waukesha positive displacement pump, model 30, (1) centrifugal pump, (1) control panel. Mounted on a stainless steel frame.

Stock# 43567020

Used- Millipore Ultra Filtration System, Type MSP 006165, Consisting Of: (1) Mavag Reactor, 200 Liter (52.85 Gallon), 316L stainless steel. Internal rated -1/3.2 bar (-14.50/46.4 psi) at -10 to 130 degrees C.(14 to 266 F.), jacket rated 6/-1 bar (87/-14.50 psi) at -10 to 130 degrees C.(14 to 266 F.). Top entering agitator, (1) Mavag pressure tank, 100 liter (26.42 gallon), 316 L stainless steel. Internal rated -1/3 bar (-14.50/43.5 psi) at -10 to 130 degrees C.(14 to 266 F.), (1) Hanag reactor, 400 liter (105.70 gallon), 316L stainless steel. Internal rated -1/3.2 bar (-14.50/46.4 psi) at -10 to 130 degrees C.(14 to 266 F.), jacket rated 6/-1 bar (87/-14.50 psi) at -10 to 130 degrees C.(14 to 266 F.). Bottom entering agitator. (2) Millipore Prostak fixed end plate filter, model PSKPUFEP-1. (1) Waukesha positive displacement pump, model 30, (1) centrifugal pump, (1) control panel. Mounted on a stainless steel frame.

Stock# 43567021

Used- Millipore Ultra Filtration System, Type MSP 006166, Consisting Of: (1) Mavag Reactor, 200 Liter (52.85 Gallon), 316L stainless steel. Internal rated -1/3.2 bar (-14.50/46.4 psi) at -10 to 130 degrees C.(14 to 266 F.), jacket rated 6/-1 bar (87/-14.50 psi) at -10 to 130 degrees C.(14 to 266 F.). Top entering agitator, (1) Mavag pressure tank, 100 liter (26.42 gallon), 316 L stainless steel. Internal rated -1/3 bar (-14.50/43.5 psi) at -10 to 130 degrees C.(14 to 266 F.), (1) Hanag reactor, 400 liter (105.70 gallon), 316L stainless steel. Internal rated -1/3.2 bar (-14.50/46.4 psi) at -10 to 130 degrees C.(14 to 266 F.), jacket rated 6/-1 bar (87/-14.50 psi) at -10 to 130 degrees C.(14 to 266 F.). Bottom entering agitator. (2) Millipore Prostak fixed end plate filter, model PSKPUFEP-1. (1) Waukesha positive displacement pump, model 30, (1) centrifugal pump, (1) control panel. Mounted on a stainless steel frame.

Stock# 45288099

Used- Finn Aqua WFI Still, Model 200-H-1. Single effect with heat exchanger, rated 116 psi at 347 degree F shell and tube sides, with controls, Serial # 34973.