Used Fluid Bed Continuous Dryers

Stock# 48805001

Used- ACT Fluid Bed Dryer, 40 Square Foot Area. Carbon steel construction. Material inlet moisture: 25%. Product outlet moisture: less than 1% maximum product temperature: 250 F drying capacity: Approximate 3000 lb/hr. Blower, carbon steel, 16,000 acfa. 14" static pressure exhauster, carbon steel, 16,000 acfm. 2.5 MM BTU natural gas burner with controls combustion chamber. Lump breaker, 2-dampers, inlet ductwork and up to 20 feet of additional exhaust ductwork and cyclone. All components are carbon steel construction. Last used in a chemical application.

Stock# 49382001

Used- Niro Spray and Fluid Bed Drying System: Rated 24 MMBTU. Double effect evaporator, last used on animal blood, poultry hydrolysis, egg, liver products, pork plasma. Includes (2) towers with titanium tube sheets, titanium heads, stainless steel shell. Rated for approximately 50,000 pounds/hour water, 30,000 pounds/hour product. System includes horizontal condenser, shell and tube heat exchanger, stainless steel tubes, carbon steel shell. Circulation pumps are in storage, Goulds stainless steel with CD4 impellers. Missing control system. Arthur Zimmer Spray drying system, approximately 30' diameter, manufactured by Niro, stainless steel contacts, fed by Niro Savoi 125 hp high pressure feed pump, rated for 1800 - 2500 PSI feed. Top of dryer includes (8) feed nozzles (typically fed four nozzles at a time). Also includes Waukesha 130 stainless steel pump, Milpointe 50,000 CFM vertical scrubber, (4) stainless steel cyclones, etc. With Wiegand single effect evaporator, rated for approximately 45,000 - 50,000 pounds/hour product, 35,000 pounds/hour water evaporation rate, 304 stainless steel construction, with dedicated boiler, Needs vacuum pump. Includes 400 hp DC drive, vari-speed, SIHI vacuum pumps, Goulds centrifugal pumps. Last used on blood products, eggs, brewers yeast, liver products, poultry products, etc. With Rotary screen, 5' diameter x 12' long, manufacture by Baycore Fibre, Type SDS 60120, Serial# 99-0210. Current replacement cost is $200,000. Includes approximately 6" diameter flange feed inlet, leading to internal distributor. Equipment has fine mesh internal screen. Spare screens. Last screening eggs. With AirChem scrubber, rated for approximately 50,000 CFM, single stage with packed bed, No controls, last used as scrubber for hydrolysis building. New in 1998, 840 GPM, 1.5" W.C., ambient. With G&H Products Tube-in-tube heat exchanger, stainless steel construction, approximately 3" diameter outer tube, 2" diameter inner tube, 25' long, (20) tubes in 2x10 sections, insulated. Brought product from 180º to 40º. Used on Dairy / Milk Products. Food Grade.

Stock# 49881003

Used- Bella Dryer/Cooler, Model D-1000E-XN. 35.32 cubic feet. batch capacity. (2) 10 hp motors. Approximate 4,562 lbs. Mfg. 2012

Stock# 48978001

Used- Carrier Vibrating Equipment Inc. Vibratory Fluid Flow Continuous Fluid Bed Dryer/Cooler Model QAD/C1260S-156"-2HP, 304 Stainless Steel Flared Deck. Approximate 186/172" long x 12" wide flared deck, drying zone approximate 9/6" long x 10"-5/8 wide or 3.2 feet squared. Cooling zone approximate 410" long x 10"5/8 wide or 1.6 feet squared. 3/16" Stroke efficiency at 650 RPM, 1/8" screen holes. Maximum product feed rate 220 pounds per hour wet, maximum discharge rate 127 per hour wet. Total drying rate 1,200 SCFM at 70 degrees F. Cooling rate 600 SCFM at 70 degrees F. Driven by a 2 HP motor. Top end inlet, end bottom outlet. Driven by a 2hp, 3/60/460 volt, 1800 rpm motor. Mounted on a carbon steel frame with legs. Includes a top cover, 10hp New York pressure blower, 2,600 CFM, driven by a 10 HP motor, Stelter & Brinck gas burner with Honeywell valves, control panel, and miscellaneous piping. Serial# 20146, Built 2005.

Stock# 49774001

Used- Carrier Vibrating Equipment Fluid Bed Dryer. Continuous, 24” wide x 20’ long, stainless steel. Rated 20 TPH (40,000 lb/Hr) Sand. Design inlet moisture: 2% maximum. Particle Size: 14-140 mesh. Inlet raw material temp: 70 deg F/ ambient. Material discharge temp: 170 to 180 deg F. Rated 2920 to 4680 SCFM. Process air temp: Up to 500 deg F. Low fire temp: 185 to 220 deg F. Fuel and pressure: natural gas x 3,000 CFH at 3 PSIG min -7PSIG max. Year 2015.

Stock# 46126001

Used- Carman Industries Fluid Bed Dryer, Model FBP-202M, 304 Stainless Steel. Approximate screen size 108" long x 28" wide, (No top hood, vibratory motors, legs, isolation springs.) Includes Fisher-Klosterman model 170-15 cyclone, carbon steel. Serial# FBP-11373, New York Blower Series 30 GI Fan, size 224, shop# C-9762-100. Driven by a 20hp motor. (1) Stelter & Brinck heating system with Honeywell controllers, and (1) Allen-Bradley PanelView 550.