Confectionary Equipment

CTM Model 3600-PA Label Printer Applicator – Pressure-Sensitive Labeler, Tamp-Blow

Used CTM Model 3600-PA Printer Applicator with Portable Stand and Parts Unit; high-speed labeler used to thermally print and apply pressure sensitive labels to moving products; Short height actuator assembly; 4" tall labels can be located 1/4" from the bottom of products; Right hand or left hand version for either side of conveyor; Up to 7.1" wide labels, up to 6.6" print width; Built-in bar codes and alpha-numeric fonts; Proven tamp-blow application; PLC control; 108-132 Volts AC, 5 Amps,54/60 Hertz, Single Phase; Pneumatic 90 PSI., 3-5 CFM; Approximately 150 lbs. Last used in a cheese manufacturing application.

Industrial Flow Meter - Micro Motion D100S-SS, 48 GPM, 400 lb/min

Used- Micro Motion Flow Meter, Model D100S-SS. 316 Stainless Steel Product Contact Areas. Rated volume 0 to 48 gallons per minute, mass 0 to 400 pounds per minute. 1" inlet/outlet, temp range: -40 degrees C to 60 degrees C. Tube pressure 2250 max.

MFR: Micro Motion

Used Domino M-Series Print & Apply Labeler – Zebra ZE500-4 Print Engine

Used- Domino M-Series Pressure Sensitive Print & Apply Labeler, Model M-Series Zebra plus-T100-Right-160-110/1. Includes Zebra ZE500-4 print engine. Capable of maximum print speed 12" / 305mm per second (203 and 300 dpi). Maximum print width 4.1" / 104mm. Maximum media width 4.5" / 114mm. Media roll size 4" / 101.6mm O.D on 1" / 25.4mm I.D. core.

MFR: Domino

Used Domino M-Series Print & Apply Labeler with Optel OP300-A Inspection System

Used- Domino M-Series Print & Apply Labeler with Optel OP300-A Label Inspection System. Domino model M400-CW100Z-280-110/254(127)-left labeler. Zebra ZE500 print engine. Left to right operation. Conveyor approximate 19-3/4" wide x 95" long. Rejection roller conveyor, approximate 24" wide x 36" long, with pusher. Optel Cartontracker model OP300-A label inspection system, serial# OP6947-03-B. Control panel with Allen Bradley powerflex drive.

MFR: Domino

Unused Eagle T200L Carton Sealer – Top & Bottom Tape Heads, 30 CPM

Unused- Eagle T200L Carton Sealing Machine. Top and bottom tape heads. Capacity up to 30 cartons per minute. Carton size range: 6" to infinite length x 6.75" to 30" width x 4.75" x 30" Height. Powered top and side belts. Set up with 2" Wide tape, head capable of 3" wide. Serial# FC1180816. 1/60/110 Volt, 8 Amp.

MFR: Eagle

3. High-Capacity Elmar 36-Head Filler & 16-Head Zalkin Capper for PET Bottles – For Sale

Used Elmar 36 Station Filler Turret with Fowler Zalkin 16 Head Pick and Place" Capping Turret complete with Infeed Timing Screw, Infeed Starwheel, Intermediate Transfer Starwheel and Discharge Starwheel all mounted on a Monoblock Main Base with the following: 3-3/4" Diameter Super Extended Cylinders (max fill range 67 fluid ounces); 3-3/4" Diameter Stainless Steel "Dome Style" Pistons with PTFE Wear Rings and 0" Ring; Motorized Volume Adjustment; Adjustable Container Rails with Replaceable UHMW Wear Surface; Quick Change Feed Screw Toolless; Change Parts Toolless; Powered Bowl Height Adjustment (3-15/16" to 9-15/16"), for Instant Height Change-Over; Central Lubrication Cluster - Lincoln Automatic Lubrication System (manual pump); Complete Electronic Control System with A-B 5/05 PLC and Operator Station with Allen-Bradley InverterDrive System , 480V/3PH/60HZ; The Elmar Industries Inc. Filler Control system is a programmable logic controller (PLC) based control system. The basic unit controls filler speed, fill volume and the No Container No Filler (NCNF) trip mechanism. Fowler/Zalkin 16-head "Pick and Place" Capping Turret (PCD 498 mm) to mount on a Elmar filler Monoblock. This turret is equipped for the application of 63 mm, screw-on closures to PET bottles, at a rate of applied closures per minute. This machine is equipped as follows: Set of Sixteen (16) Zalkin BH-3 Hysteresis magnetic clutch heads for screw-on closures requiring an application torque of 12 to 36 inch pounds +-10%; Heads are equipped for use with quick change chucks for cap handling and application; Set of Sixteen (16) quick change chucks for the 63 mm screw-on closure. Quick change chucks use a ball and ring assembly for quick release from, and remounting to, the capping head; Telescoping cap chute suitable for the 63 mm closures and suitable for mating with "Nose Over' chute; Cap chute steam cloud box (15" x 3' x 4 long) and cap transfer steam manifold, supplied to heat cap prior to application; Quick Change "Peg & Ring" cap transfer system for smooth closure pick-off from the discharge of the cap chute and transfer to the capping heads. Transfer system is equipped with quick change quick release features to allow for no tools change-over. Transfer system includes sensors for no bottle/no cap control.; Self-contained elevating system for adjusting height of capping turret as required by differing heights of containers. Safeties are included to prevent travel beyond machine limits. Minimum 4", maximum 12" height of container.

MFR: Elmar

Used E-Pak 16 Head Automatic Inline Liquid Filler Microprocessor Controlled

Used ELF E-Pak 16 Head Inline Gravity Pressure Liquid Filler. Has KAPPS-ALL filler heads. Fully automatic, Microprocessor-controlled, Straight-line filler. Approximate OAD 60"x 50"x 80".

MFR: E-Pak Machinery

Used FANUC ARC Mate 120iC Robotic Arc Welding System with Lincoln Electric Power Wave i400

Used FANUC ARC Mate 120iC Robotic Arc Welding System with Lincoln Electric Power Wave i400. High-speed arc welding and cutting robot. Six-axis movement capabilities. Maximum reach of 1,811 mm. 20 kg maximum load at wrist. Repeatability within 0.03mm. Paired with a Fanuc R-30iA controller, and a Lincoln Electric Power Wave i400, robotic-grade electric welding power source. Includes teach pendant. Built 2010.

MFR: Fanuc

Used Fanuc R-2000iC/210F Heavy Payload 6-Axis Industrial Robot with R-30iB Controller & Welding Gun

Used Fanuc R-2000iC/210F Heavy Payload 6-Axis Industrial Robot with R-30iB Controller & Welding Gun. 6-axis movement. Maximum capacity at wrist 210 kg. Maximum reach 2,655 mm. Repeatability within 0.05 mm. Paired with a Fanuc R-30iB controller, and has Leoni Hose assembly. Robot is equipped with a welding gun. Robot serial #R18303868, built 2018.

MFR: Fanuc

Used Fanuc R-2000iB/250F 6-Axis Robot – 250kg Payload, 104.5” Reach, R-30iB

Used- Fanuc 6-Axes Articulating Robot, Model R-2000iB/250F. Has a 2655mm (approx. 104.5") maximum reach and a maximum wrist load capacity of 250kg (550lbs). Servo driven. Includes Fanuc R-30iB CPU controller and learning pendant. Built 2015. 3/5/60/480V.

MFR: Fanuc

Used Fanuc M-420iA Industrial Robot | 4-Axis 40kg Palletizing Robot w/ R-J3iB Control

Used Fanuc M-420iA Industrial Robot | 4-Axis 40kg Palletizing Robot w/ R-J3iB Control. 4-axis movement capabilities. 40 kg payload capacity. Maximum reach of 1885 mm. Linear motion speeds up to 4,200 mm/sec. Repeatability within 0.5 mm. Includes R-J30iB intelligent robot control system. Includes dedicated pneumatic and electrical connections at the wrist (8 digital inputs/8 digital outputs).

MFR: Fanuc

Used High-Capacity Fanuc M-410iC/500 Robot – 500kg Load, 4-Axis Arm

Used- Fanuc Model M-410ic/500 Articulating Robot, 4-Axis. Has up to 500kg payload capacity and up to 3143 mm of reach. Includes stand and end of arm tooling. Last used in palletizing operation. Has Fanuc controller. 3/60/460V.

MFR: Fanuc