Complete Plants For Sale

Stock# 51308002

Used-Rossi Catteli S.P.A, Parma, Italy Natural or Concentrated and Aseptic Filling Plant with a capacity up to 20 tonnes/hour of fresh fruits or tomato puree consisting of: (1) Puree extraction unit, (1) Concentrate unit, (1) Discharge section unit, (1) Sterilization unit, (1) Aseptic filling unit, (1) Wastewater treatment unit. Complete with piping, pumps, sensors, valves, platforms, steel structure, controls and additional infrastructure. New 2007.

Stock# 52857001

Used- Crown Iron Works, Model 48, Milling Ring Flash Drying System. It was designed and used for food-grade orange pulp with 17,000 Lbs/Hr capacity but the plant can be used for a wide range of applications in various industries including: Drying food products such as grains, cereals, fruits, vegetables, herbs, and spices. Pharmaceutical ingredients, intermediates, and final products Drying various chemicals, including powders, granules, and crystalline materials Drying minerals and mining products such as ores, concentrates, and mineral powders Animal Feed Drying and processing environmental materials, such as sludges, biomass, and waste products. System designed for drying of powers, filter & centrifuge cakes, and slurries where a discrete and fine end product is desired. The Milling Flash Dryer is basically a low energy jet mill, that uses jets of low-pressure air to encourage inter particle collisions between pieces of feed material. These inter particle collisions break up the feed material in the dryer with no moving parts in the dryer or airstream. The dryer is in the shape of a torus, or donut that is broken up into 2 basic areas: (1) Manifold & Milling area; (2) Classifier. The ideal feed material for the Flash Dryer is a crumbly and free flowing cake that breaks up readily when it enters the drying air stream. The feed material enters the recirculating hot air upstream of the first nozzle, with the centrifugal forces generated by the air concentrating the material in the area above the nozzles. Particle-to-particle collisions begin immediately, deagglomerating the material before hard agglomerates can form. A tremendous amount of surface area is created allowing evaporation to occur quickly, thereby depressing air temperature in a very short period of time. Centrifugal forces are generated by the recirculating gases within the dryer, forcing the larger particles to the peripheral walls. Finer material is displaced towards the inside radius of the dryer where the classifier outlet is located. Fine product exits the dryer along with the exhaust gas vapor. Larger particles or agglomerates are recycled to the nozzle area dryer for further de-agglomeration and drying.

Stock# 48962018

Used- Natural Gas Treatment Plant with a capacity of10,880,000 m3/day (384,223,000 cfd.) consisting of: (1) Natural Gas Treating/Sweetening unit, (1) Natural Gas Drying unit, (1) Natural Gas Chilling System, (1) Condensate Stabilization unit, (1) Hydrogen Sulfide Incinerator unit. Incl. piping, pumps, sensors, valves, and additional infrastructure. Constructed and designed by MT-Monberg &Thorsen A/S Copenhagen (now MT Hojgaard) and Comprimo B.W Amsterdam (now Worley Comprimo) as a back-up plant for an offshore treatment plant capacity typically used 15 days per year during offshore plant maintenance, occasional operational standby testing and to process.

Stock# 53091007

Used- Joule Thomson Effect, Refrigerated Joule Thomson Effect (J-T) Natural Gas Liquids Extraction Plant" Consisting of: Mol Sieve Dryer Skid and Accumulator/Economizer Skid: AND JT Skid with Liquid Separators: - 1,535 MBTU/HR Cold gas/ gas exchanger, 1200 PSIG Tube 720 PSIG Shell - High Pressure Cold Separator, 24" x 8, 1200 PSIG- Low Pressure Cold Separator, 30" x 10, 720 PSIG - Optimux 4 20 mA controllers, Rosemount guided wave level transmitters, Foxboro pressure and temperature transmitters - Accumulator, 36" x 8 300 PSIG - Economizer, 24" x 8 300 PSIG - Optimux 4 20 mA controllers, Rosemount guided wave level Transmitter, Foxboro pressure transmitters - 15,000 MCFD at = 10 lbs/MMSCF water inlet for 1 PPM water outlet - Inlet Coalescer: 16" x 76", 1200 PSIG, - Inlet Dryers: 42" x 116", 1200 PSIG - On skid PLC controlled 120 kW regeneration gas heater- 10 Micron dust filter, 1200 PSIG - Regeneration gas cooler and separator, 301 MBTU/HR, 250 PSIG - Optimux 4 20 mA controllers, Rosemount guided wave level transmitters, Foxboro pressure and flow transmitters-Electronic controlled, pneumatically operated AE switching valves AND Chiller kid - 2,119 MBTU/HR Warm gas/ gas exchanger, 1200 PSIG Tube 720 PSIG Shell- 949 MBTU/HR Chiller, 1200 PSIG Tube 300 PSIG Shell- Vaporizer, 300 PSIG - Optimux 4 20 mA controllers, Rosemount guided wave level transmitter, Foxboro pressure transmitter. Also includes Skid Mounted Gas Compressor 800 HP, 15 Foot Bore x 16 " Stroke, 300 to 400 rpm, with Harsco Model Ajax 108H Gas Cooler and DCL Model RCZ2110V14 Exhaust Muffler and Accessories. Delivery and Metering System to Include: ECI Battery Cabinet (2013) Hydra-Cell Model D10C9300002 , Explosion Proof Pump (2014), Micro Motion Midel CMF50M314N6BAEZZZ Mass Flow Meter (2014) Micro Motion Model CMF300M356N6BAEZZZ Mass Flow Meter (2014) with Assorted Piping nd Valves and Holding Tank, Liquid Controls Model ESAR/SP3 Flow Meters, (2014) Each with Digital Readouts and Accessories; (Readouts are Located in Office), Explostion Proof Pump, (2013) 20 HP. Explosion Proof Pump (2013) 20 HP, etc.

Stock# 53343001

Unused- 10 MGY Biodiesel Plant. Catalyst mixing station; Feedstock dosing station; Feedstock preheating; 1st Transesterification dosing station; 1st Transesterification reactor; Biodiesel heat exchanger; Intermediated glycerin settler; 2nd transesterification dosing station; 2nd Transesterification reactor; Final glycerin setting station; Ion exchanger station; Resin filter system; Methanol dryer; Condensate separator; Finished fine filter system; Chillers; and miscellaneous components. German built in 2013 and never installed. Breakdown of components available.

Stock# 40090002

Used-Air Separation Unit (ASU) Plant. Produces 400 KSCFH of Gaseous Oxygen (GOX) at 200 psig and another 100 KSCFH of Gaseous Oxygen (GOX) at 3 psig, Oxygen Purity 99.5%, N2 Purity less than 10 PPM O2. This ASU plant also makes 100 KSCFH of Liquid Oxygen (LOX) & 200 KSCFH of Gaseous Nitrogen (GAN) at 400 psig, plus 69.2 KSCFH of Liquid Nitrogen (LIN) and 23.9 KSCFH of Liquid Argon (LAR) Less than 1 PPM 02 and less than 1 PPM N2. The plant has a film-type main vaporizer with two BAHX closed cores supplied by Sumitomo and is equipped with an alumina/CaBaX air purification system. The natural gas fired heater provides heat for regeneration. HP column has trays. LP column and two argon columns have packing. Argon production is cryo-argon" type. Liquid dumping is through forced air dump vaporizer. The LP liquid products are stored in two 525,000-gallon LOX and LIN flat-bottomed storage tanks. LAR is stored in an 11,000-gallon tank. The HP LOX and HP LIN are stored in a 6000-gallon tank and 13,000-gallon tank, respectively. The backup system is a hot water bath vaporizer with an estimated capacity of 1000 KSCFH and multiple coils (GOX, GAN, and Tank pressurization coils). The two hot water boilers are natural gas fired. LOX, LIN, and LAR trailers are loaded by pumps in one load-out station. A single scale provides Gross & Tare weights of trailers. The control system is comprised of (5) AB PLC5 processors with remote IO in 11 cabinets. The HMI was iFix32 installed on Windows XP. There are very few pneumatic and single-loop electronic controllers. However, no local panels are present at the compressors. Electricity is delivered to the site via aerial cable by Axiell/Westlake. The electrical system includes main plant, 34.5 KV high voltage electrical substation and overhead distribution lines from Axiall/Westlake cogen units to the substation. The distribution substation consists of a 34.5 KV to 13.8 KV 20MVA Transformer, an elevated PDC building containing a 13.8 KV Switc.

Stock# 52980001

Used- Animal Protein Feed Line. Rated 3-5 tons per day. Consists of the following components: UAS model UFSP112X110D carbon steel hammermill, 350hp motor, dust collector. UAS hammermill, 150hp motor, dust collector. Fulton Model ISCS60 fuel-fired steam boiler natural gas, rated 2,070lbs per hour. Geelen counter flow Dryer-Cooler Type VD28X38J, 3-deck stainless steel, equipped with Maxon 2100kW natural gas burner model oven pak type EB-6, cyclone, dust collector, 60hp blower, control panel. Karl Schnell 225mm emulsifier. Stainless steel grinder. Dust collectors. Control panel. The plant was designed to process grains and animal byproducts to produce chicken feed protein. Silos are not included.

Stock# 41174054

Used- Rebuild ANHYDRO falling film vacuum evaporator. Complete ANHYDRO falling film vacuum evaporator with mechanical vapour recompression units Was originally designed as a TVR evaporator and in operation for milk concentration in a Norwegian dairy. This evaporator plant was relocated and redesigned by BONTECH A/S (Denmark) for 6.500 kg/hour water evaporation for stick water from fish industry and now operating with 2 units of mechanical vapour recovery units (MVR) in serial connection. The 5 calendria has a total of 121, 100, 38, 38 and 13 pipes - each ?51 mm and 7 meters long. It is complete with CIP plant and still installed. This plant is in excellent working condition and ready to be relocated and put back in operation, after reconditioning of pumps etc. The Westfalia separator is not included in this listing.

Stock# 14191087

Used- Weatherly High Pressure Nitric Acid Plant, 500 STPD. Ran at 535 MTPD, turn down ratio 88%, Ammonia consumption 0.304. Includes the following equipment: Ingersoll-Rand 5-stage centrifugal air compressor, 49,453 SCFM (dry) at 14.7 psia and 60 degree F, Ingersoll-Rand E-4331 hot gas expander, Compressor train rebuilt in 1994. Installed new economizer, high-pressure intercooler, low-pressure intercooler, surface condenser, high pressure filter, Absorber column 12' diameter x 66' height, 18 absorption trays and 4 bleaching trays. New Cooler condenser (2003), new surface condenser (2005), new intercoolers (2006-2007), new waste heat boiler (2013).

Stock# 51077001

Used-PESCO Oil Re-Refining Plant. Rated for 10,000 Gallons / 250 barrels per day of used Motor Oil and Diesel Oil. Plant includes: PESCO Re-refiner, 4 clay processors, fuel boiler, incinerator, two air compressors, and a water cooler. The plant is fully operational and is currently running. Plant produces 110 or 240 base stock. Year 2009.

Stock# 52984001

Used-20mW Steam Generating Power Plant with building and supporting structures. The plant includes: (1) WEG 2625Kva 11,000-volt synchronous continuous duty alternator (built 2012) (1) Triveni 20 mW steam bleed condensing turbine with gearbox (built 2012). The 20,000kW power rated steam turbine has inlet steam pressure of 40 bar and steam temperature of 400 degree C and a turbine speed of 6,150RPM. 21,800kW powered gearbox has an input speed of 6150RPM and output speed of 1,500rpm. The plant includes ACC vacuum condensing equipment, a RO water plant capable of 5000 Ltrs per hour, a condensate polishing plant and includes all ancillaries . This unit was commissioned in 2015, saw little use and is offered for sale in it's mothballed condition with the turbine bared regularly. Also available for sale as a complete package with the plant or as a separate purchase is an unused Triveni 20mW steam bleed condensing turbine with gearbox.

Stock# 10715061

Used-Mini / Nano Mill" Just in Time" Steel Mill for the manufacture of steel billets, rebar, rounds, flats, squares, and angles. Featuring: Melt Department-2 Electric Arc Melting Furnaces, Refining Furnace. One Furnace is 5 ton and the other is 7 ton capacity. Transformers: 4MVA Westinghouse and 3MVA Westinghouse. The primary voltage of transformers is 13800 V and second variable 96v to 250V. 2 Bridge Cranes, Pots, Ladles, Danieli Continuous Casting Line, Dust Collection System, Steel Yard Equipment-2 Front End Loaders, 30 Ton Yard Crane, Dump Trucks, Yard Scales, Billet Reheating System-Furnaces, Transfer Systems, Coolant System, Shear, Prep Area, 3 Cranes, 12 Stand Rolling Mill, Cooling, Shearing, Packaging System, General Plant Equipment- Transformers, Lab, Water Treatment Systems, Pots and Ladles, Air Compressors, Cat Generator, 10 Ton Outdoor Overhead Crane System, Forklifts, Yard Cranes, Front End Loaders, Machine Shop/Maintenance Shop and More. ?the Plant has two principal parts: 1. The melting furnaces and where final product is a billet (measures 57.15mm x 57.15mm up to 130 mm x 130 mm max) in a continues casting machine. 2. The Rolling Mill, Produces small batches of different commercial steels: Round, Flat, Square, Angles and Rebars, The plant is adaptable for other Long products using same Hot Process. average capacity of the end products of rolling mill per year 2,400 Ton Rolling Mill ( the rolling has minor capacity that the melting and continuous casting than have 3,500 ton per year. All the equipment can use 460/440/400 Volts and 60 Hz, All the American devices uses 60Hz and some time 60/50 hz, but not all. Yr. 2018.

Stock# 10986016

Used-Palm Oil Refinery Plant. Rated 120 Tons per day. Winterizing Deodorizer. Can also produce soy, peanut, and canola oil. Includes (2) boosters, (2) condenser, (2) ejectors, (2) heaters. (4) Filters, (2) at infeed and (2) at discharge. (2) Flow meters with electronic transmission and (2) heat exchangers. (4) Tanks with pumps and motors. Totally reconditioned in 2014. Brought up to efficiency standards. Info and drawings available. With Corn Washing, Drying and Bagging Plant for Corn Flour. Rated 2.5 Tons per hour. Running 5 lbs bags at 30 BPM. Includes: Corn soaking vessel, approximate 36" diameter x 18 long screw. Steam injected. Corn washing separation. Pneumatic sir system. Sifter, holding bin, dust collector, hammermill, finished product bin. (1) Manual clamp bagger, approximate 15 bpm, 25 kilo/50 lbs bags. Elevator. Stainless steel screw conveyor, approximately 10" x 20 long. (2) Hoppers. (1) Form, fill, seal bagger machine, 1lbs bag at 60 per minute. (1) Speedy manual bag machine, 1lbs bags at 15 per minute. With Liquid and Solid Crystallizer Filtration Plant. Rated 200 TPD for solid, 120 TPD liquid. Includes: (2) Crown Iron Works crystallizers. (1) Andritz filter press, (34) 55" x 55" square plates. (1) Liquid cooler with screw compressor. (1) Cooling tower. (2) Compressors with water and oil separator. (2) Liquid flow meters. (2) Stainless steel heat exchangers. (1) Hopper for solids extraction. (12) Pumps with motors. (10) Butterfly valves. (5) Vertical Stainless-steel tanks. (6) Stainless steel finished product tanks, 91-ton capacity each, 16 diameter x 22. Yr. 2014. A 5% Buyers Premium based upon final sales price will be assessed to the purchaser.