Used Bakery Equipment

Stock# 49825004

Used- VMI Varymix 2200 Continuous Mixer. Stainless steel construction. Capacity 4,000 lbs per hour. Includes (2) main tanks for flour and bran. (3) Micro ingredient tanks. Glycol information: Run @ -5 to -7 degrees, capacity 40 cubic meters per hour, 2.5 bar pressure. Overall dimensions approximate 345" long x 161" wide x 171" tall. 3/60/600 Volt.

Stock# 51648004

Used- LJ White Spiral Cooling Conveyor, Model 23040. Approximate 20' diameter. Stainless steel wire 38" wide belt. 5 Revolutions. Driven by a .5hp, 3/60/230/460 volt, 3450 rpm gear motor. Approximate 5" tier pitch. Useable belt width 36". Approximate infeed height 40", approximate 68" discharge height. Straight through configuration, counter clockwise rotation. Mounted on aluminum frame. Serial # 38-AL-840-R.

Stock# 52189024

Used- Shangha Target 11" Rolling & Scoring Line. Designed to make chiclets. Consisting of: Twin Screw extruder with 5" diameter screws, electrically heated, die for 11.5" sheet, Dusting conveyor, TG Machine model CX (3) sets of sheeting rollers measuring approximate 15.5" wide x 7" diameter. 60" long x 36" wide, Two jacketed scoring rollers to make approximate 3/4" x 3/4" chiclet.

Stock# 52189025

Used- Shangha Target 11" Rolling & Scoring Line. Designed to make chiclets. Consisting of: Twin Screw extruder missing screws and die with motor drive, (3) sets of sheeting rollers measuring approximate 15.5" wide x 7" diameter. 60" long x 36" wide, Two jacketed scoring rollers to make approximate 3/4" x 3/4" chiclet.

Stock# 53176001

Used- Industrial Crepe Production Line. Stainless steel agitated tank batter mixer; Diaphragm pump; 6' wide x 8' tall Crepe wheel; 6" IR burner, 60,000 BTU/hr, with ignition and flame monitoring end plate; 19' conveyor; Driven by a 7.5HP motor.

Stock# 53262001

Used- Kuipers Pellet Frying Line. Consists of: pellet feed and dosing system; Vibratory tray; Used-oil storage tank; Fresh oil supply tank; Defatting belt, Rotating mixing drum; Screw type flavor dosing system; Rotating vane type flavor spreader; Electric control board; Frame. Built 2013. Previously used to fry snack pellets. Pellet receipt and feeding system that allows the operator to supply pellets from floor level; The pellet feeding elevator brings the product to the vibrating sieve.This ensures a continuous flow into the fryer and sieves small particles. Kuipers universal pellet fryer helps produce any type of pellet snack in the most efficient way possible. Its innovative product belt transports the product and ensures minimal oil volume is used within the system. The frying oil can be heated electrically or with thermal oil.The defatting belt allows excessive frying oil on the product surface to drip off, after frying. For irregular shape product, the belt has a tipping point halfway. The drip-off frying oil is then returned to the fryer. Air knives can be added for further removal of oil. The product is then fed into the flavouring unit. This is a stand-alone, drum-shaped mixing system with accurately controlled speed and flavour or salt dosing. The unit has its own control board. The frying time and temperature are adjustable to allow producers to manufacture all types of pellets. The system is fully controlled via the PLC system. Specially developed dirt removal system, combined with gentle heat treatment the oil does not have to be replaced - and without the addition of any chemicals. Efficient removal of small particles begins before frying to prevent these from entering the frying system. This contributes to an extremely low frying oil turnover time, in most cases less than three hours.

Stock# 52529001

Used- Mimac type DBE Food Equipment Inc Cookie Dropper / Depositor, Model DEP2001. Can handle 400mm wide trays. Speeds up to 30 cycles/min deposited. Approximate 120mm Maximum stroke. 29 Liter hopper capacity with roller heads. Wire cutting. Has (5) Moulds. Rasotto C500 controller. Mounted on casters. 3/60/220 Volt, 10 amp power requirements. Serial# 99339.

Stock# 50542001

Used- Aeroglide Model FBU24-25-RGX-IDFB Toasting and Puffing Baking Oven, Serial # 08073-01 (2009). Airflow: Fluid Bed with Carrier 26" x 30' Long x 9" Deep. Stainless Steel Vibratory Conveyor, 10 hp, Maxon Burners, (2) 10 hp Exhaust Blowers, (2) Process Blowers, (2) Rotary Discharge Valves, Tube material is Carbon Steel, 20 Gauge, 2 independent Heat Zones. Effective Bed Length 25'. Effective Bed Width, 2'. Drying/Toasting Area 50 Square Feet. Aeroglide Model C1-36-18-XXC 36" Wide Cooling Tunnel, Serial # 08073-02 (2008). 409 Stainless Steel Construction with 304 Stainless Steel product contact parts with Perforated Belt. Approximate 16' Long, 8" Deep, Twin City Blower Side Draft Exhaust Blower. Last used on Guar Gum.

Stock# 43947003

Used- APV Baker 16" Frozen Cookie Dough Machine. Unit in good working condition. Electrics 3/60/460V.

Stock# 53015001

Used-Baker Perkins Wire Cut 16" Servo Driven Wire Cut & Continuous Rope Extruder. Originally designed to cut pucks of cookies onto wax paper sheets. All servo driven, Allen Bradley controls with touchscreen. 16" wide two roll extruder, wire cut oscillating knife. Continuous extrusion capable for ropes, paper feed roller for cutting products onto paper, has raising and lowering bed, guillotine cutter for wax paper but can also be used to cut ropes of product to specific lengths. OAD 11'l x 4'W 3/60/480v. Has die with 5 outlets measuring .625" x 1.25" cookie dough

Stock# 49825001

Used- Benier Baguette and Roll Line with VMI Verymixer. The line can make long pieces of bread much like a baguette. Rated at 600 grams per piece, it can do about 3,000 pieces per hour. At 350 grams it is rated for approximately 3,200 pieces per hour. Bread line mixer has an output of 1,800 kg per hour. The Benier moulder output varies greatly depending on the size of each piece. Capacity: 3,000 Dough Pieces Per Hour. Dough Weight: 250 - 465 Grams (8.81 oz - 16.40 oz). Cutting Pattern: 1, 2, 3, 4, 5. And 6 Parts Pan Dimensions: 800mm x 600mm x 40mm (31.49" x 23.62" x 1.57"). The entire line is manufactured by Benier in 2002, with the exception of the mixer being a VMI mixer. Year 2002.

Stock# 49825002

Used- Benier Baguette Former, Model French Mould. Multi Stage Moulding for lengthening baguettes. Capacity 3,000 pieces per hour @ 21.16 oz (600 grams) & 3,200 pieces per hour @ 12.34 oz (350 grams). Consisting of: Moulding head, 1st pressure board, 2 Rest time conveyor, 2nd Pressure board. Stainless steel construction. 3/60/600 Volt. Built 2002.

Stock# 49825003

Used- Benier Bread Line. Capacity 3,000 dough pieces per hour. Dough weight 5 pocket divider range from 140 to 800 grams. Line consisting of: Benier model B9350 5 pocket divider, machine can do 5 x 1.500 pcs/h maximum, minimum gram can be processed at max 7,500 pcs/h with max gram 1.200 strokes/h equals 6,000 pcs/h, weight range per pocket 140 - 800 gram (4.9 - 28.2 oz), drive unit 3/4kW. Preshaper. Double indexing infeed system. First Prover type 800N, net load 800 dough pieces, proof time: 16 minutes and 13.3 - 10.7 - 8.0 - 5.4 minutes, (75) 12 - Portioned pocket swings. Isolation box. Climatization, Type ACK-ED. Conveyor. Curve 90 degree conveyor. Conveyor. Switch board panel. ***This unit will need a new insulated box around the proofer.***

Stock# 53314001

Used- COMAT Mozzarella Molding Machine, Model M22TR. Rated 4400-5500 lbs/hr (2000-2500 kg/hr). Includes (2) 8oz and (2) 16oz molding; Components included: pre-hardening heads; water chilling unit; CIP System. OAD: Approximate 6' H x 10' W (not including CIP/water chiller). 3/50/220V.

Stock# 53290008

Used- Hobart Vertical Mixer / Cutter, Model HCM300. 30 Quart capacity. Approximate 10" diameter bowl with cover. (2) Cutter / Knives, driven by a 5hp, 3/60/230/460 volt, 1140 rpm motor. Manual Bowl tilt. Mounted on frame. Serial# 31-367-347.

Stock# 52189019

Used- Loynds Electric Tray Oven, Model GO. (5) Shelves, inside dimensions 24" deep x 26" wide x 33" tall, digital controls, 3 phase, 220 vols, 5.4 kw. Serial# 1435/2, built 10/2019.

Stock# 52189023

Used- Loynds 300 mm Wide Rolling & Scoring Line. Designed to make chiclets. Consisting of model GFL Dual Twin Screw Extruder with electric heating system, 3.75" diameter screws, 320 mm die for sheets, 16.4 kw (22 HP) 3 phase, 60 cycle, 220 volt motor, 60" long x 27" wide. Serial# 1435/5 built 10/2019, Inclined conveyor to apply starch to bottom and type of sheets, (6) sets of jacketed sheeting rollers 13-3/8" wide (340 mm) x 6" diameter, adjustable thickness, 96" long x 36" wide, Two sets of scoring rollers to make an approximate 3/4" x 3/4" chiclet, Model GFL tumbling drum 29" diameter x 70" long with partially perforated drum, motorized lift to discharge, forward and reverse controls for drum, 2 HP, 3 phase, 60 cycle, 220 volts. Serial#1435/5-C. LINE NEVER INSTALLED.

Stock# 51648005

Used- Custom Dry Ingredient Spreader with Spray Nozzles. Consists of: (1) Martin E-Z dry ingredients spreader, approximately 35-1/2" wide. (2) Spraying Systems Co spray nozzles. Approximate 36" wide x 84" long wire mesh belt. (1) Allen Bradley Powerflex 40 drive. Mounted on stainless steel frame with casters. No manufacturers tag. 3/60/230 Volt.

Stock# 45176030

Used- Nu-Vu Electric Deck Oven, Model MDO-2/4/Pro-6. 2 Deck Oven/12 Pan Proofer. Serial # 29358. ** SALE SUBJECT TO SELLER'S APPROVAL **

Stock# 43947002

Used- Polin Multidrop Cookie Depositor. New acrylic side safety door, wire cut capable but missing bar and fingers. Has been cleaned, tested and good running condition. Elec: 3/60/220V.

Stock# 53299001

Used- Polin Multi-Purpose Depositor with Wire-Cut and Nozzle Rotation, Model Multidrop Classic - TS Fast 66FL. Stainless steel frame and exterior panels; Mounted on braking casters; Easily detachable table; Automatic tray feeding; Hard to soft dough side adapters; Inverter driven roller motor; Inverter driven motor with encoder for horizontal table movement; Independent motor with encoder for vertical table movement; Inverter driven motor with encoder for nozzle rotation; Hard dough head with stainless steel rollers and aluminum sides; Head is easy to disassemble for cleaning; Multiple types of interchangeable heads available; 100 program touch screen computer with the following functions: MENU - control rollers, table, nozzles, and recipes, CHECK - allows individual control of all motors/sensors for proper function, SERVICE - for monitoring scheduled maintenance, INFO - for information on all functions and help pages. ALARM LOG - records all alarms that occur throughout production; USB connection to upload or save recipes; Ethernet connection for remote service; 50 liter hopper capacity; Electrical: 220V/60Hz/3Phase 1.6 kW. Includes: Twisting Die, Classic, 660mm Trays, M45 x 3 Thread, P=103, 6 Exits; Sheet Die, Sponge Cake, 620mm Trays, 600mm Width, Adjustable, Thickness (max. 15mm); Nozzle, Single-Color, Brass, 45x3, Thread, Smooth Off Center, Long, Oblong Shape, D=80mm. Built 2021. Overall dimensions (mm): 1155 W x 1380 L x 1410 H, Net weight (kg): 320 kg.

Stock# 53299002

Used- Poling Multi-Purpose Depositor with Wire-Cut and Nozzle Rotation, Model Multidrop Classic "CE" 46MTR/FL. Stainless steel frame and exterior panels; Mounted on braking casters; Easily detachable table; Automatic tray feeding; Hard to soft dough side adapters; Inverter driven roller motor; Inverter driven motor with encoder for horizontal table movement; Independent motor with encoder for vertical table movement; Inverter driven motor with encoder for nozzle rotation; Hard dough head with stainless steel rollers and aluminum sides; Head is easy to disassemble for cleaning; Multiple types of interchangeable heads available; 100 program touch screen computer with the following functions: MENU - control rollers, table, nozzles, and recipes, CHECK - allows individual control of all motors/sensors for proper function, SERVICE - for monitoring scheduled maintenance, INFO - for information on all functions and help pages. ALARM LOG - records all alarms that occur throughout production; USB connection to upload or save recipes; Ethernet connection for remote service; 35 liter hopper capacity; Electrical: 220V/60Hz/3Phase 1.6 kW. Includes: Twisting Die, Classic, 460mm Trays, M45 x 3 Thread, P=108, 4 Exits; Sheet Die, Sponge Cake, 460mm Trays, 400mm Width, Adjustable Thickness (max. 15mm); Nozzle, Single-Color, Brass, 45x3, Thread, Smooth Off Center, Long, Oblong Shape, D=80mm. Built 2021. Overall dimensions (mm): 1155 W x 1380 L x 1410 H, Net weight (kg): 320 kg.

Stock# 10986018

Used- Reading Bakery Systems 48"W Ultrasonic Guillotine Cutter. Has Allen Bradley CompactLogix L16ER, PanelView 1000 touch screen controls. 136"L x 80"H x 120"H. Elec: 3/60/460V, 22.73 amps.

Stock# 48193005

Used- RHEON Cornucopia KN135 Encruster. Capable of forming between 20 -100 pcs./min. with an average weight of pieces 10-250 grams each or a total maximum output of 280 Kg/hr. Has several forming capabilities including bar. shaped encrusting, continuous Extrusion, double filling extrusion, encrust solid material, and open top shape. Equipped with 6 Jaw forming heads. Has 713.8 hours. Built in Oct. 2019. Electrical requirements 220 Volt 3 Phase, 1.09 KW, 50/60 Hz, 5.8 Amps

Stock# 52394006

Used- Cinelli Esperia Corp. Spiral Mixer, Model CC-160KG/STL. Hoist deposit system. Approximate 36" diameter bowl. Flour capacity 233 lbs. Finished dough capacity (based on 50% moisture content) 353 lbs. Serial# 0211-609.

Stock# 51648010

Used- Dough Extruder / Sheeter with Rotary Docking/Cutter Roller. Set up for (2) Rows. Top feed hopper, no cover. (2) Rolls, approximate 16" wide. Air actuated die cutter. Approximate 16" wide mesh discharge belt. Control panel with (2) Allen Bradley powerflex 40 drives. Mounted on a stainless steel frame. No manufacturers tag.

Stock# 52189017

Used- Winholt Equipment Electric Heater Proofer, Model NHPL-1836CA/LC. Temperature and humidity controls, 34 shelves for approximate 26" x 18" bakery trays. (3) perforated trays included, inside dimensions 52.5" tall x 18" wide x 26" deep, on wheels, 120 volts, 13.5 amps. Order# 684676.