More Info
Width (in.): 78
Manufacturer: WELEX
Roll Diameter (in.): 18
Model: 17.5 X7 8
42167001
Used: 78” wide Welex “J” style sheet line, consisting of the following: (1) Welex 4.5” extruder 4.5” screw diameter, 30:1 L/D ratio, side vented. Barrel is electrically heated and water cooled. Gearbox rated 263 hp having a 17.55:1 gearbox ratio. Motor is direct connected under barrel, 250 hp 1750 RPM DC. Unitized control panel equipped with 14 solid details
|
More Info
Width (in.): 49
Manufacturer: Kaufmann
Roll Diameter (in.):
Model:
10665016
Used-49.2" (1250 mm) Kaufman Coextrusion Sheet Line. (1) 3.54" (90 mm) Kaufmann model 90-33d extruder, vented, vacuum pump, 150 hp DC motor, bolt throttle device; 3.54" (90 mm) lantern slide screen pack changer with hopper and loader, thyristor drive, high quality temperature control panel; (2) spare screws PS/ABS, PP/HDPE type. (2) 2.55" (65 mm) Kaufmann details
|
More Info
Width (in.): 31.5
Manufacturer: Kaufmann
Roll Diameter (in.): 118
Model:
14006004
Used-Kaufmann Sheet Film Downstream Equipment. Hydraulic screen changer with power station, melt pump with DC drive and torque shaft, 31.5" (800 mm) T-die with flex lip and deckling device. 3 roll polishing stack with roll diameter 118"/177"/177" (300/450/450 mm), width of rolls 31.5" (800 mm). 2 roll puller, (1) chrome and (1) rubber plated roll, control details
|
More Info
Width (in.): 79
Manufacturer: Kaufman
Roll Diameter (in.):
Model:
10665015
Used-79" (2000 mm) wide Kaufman Co-Extrusion Sheet Line. (1) 6" (150 mm) Kaufman 33D extruder, heated/cooled, vented with vacuum pump and control panel. (1) 3.5" (90 mm) co-extruder, vented with vacuum pump, 100 hp DC motor, ASEA thyristor drive, temperature control panel. (1) Melt pump, (1) 79" (2000 mm) die, (1) 79" x 18" (2000 mm x 450 mm) 3 roll details
|
More Info
Width (in.): 4.5
Manufacturer: KILLION
Roll Diameter (in.): 5
Model: KN250
41901001
Used- Killion 4-1/2'' Wide Sheet Line Consisting Of: (1) Killion 2-1/2'' single screw extruder, model KN250, approximately 10 to 1 L/D ratio. Electrically heated, air-cooled 3 zone non-vented barrel. Water cooled feed throat with a roll type feeder. Approximately 42'' centerline height. Driven by a 40hp, 500 volt, 1750 rpm DC gear motor thru a Koellmann details
|
More Info
Width (in.): 15.6
Manufacturer: Leistriz
Roll Diameter (in.): 5.85
Model:
41867001
Used-Leistriz Lab Size 3 Roll Sheet Stack. (3) 5.85" diameter x 15.6" straight side, 2 fixed and 1 removable chromed rolls, steam heated rolls. Includes downstream/haul-off. (2) Gearboxes driven by (2) 380 volt/50 cycle/3 ph motors. Control panel mounted on unit. Includes emergency stops. On wheels. Overall dimensions: 5'2" long x 2'9" wide x 4'9" high details
|
More Info
Width (in.):
Manufacturer: Farrell
Roll Diameter (in.): 12
Model:
14053000
Used-Farrel Bridge PS/PP Thermoforming Line consisting of: (1) Farrel Bridge single screw extruder, 100/32 D with degassing and Labotec volymetric dosing unit for (4) components. (1) Welex coextruder, 40/30 D. (1) Cresta hydraulic screen changer. (1) Maag computerized gear pump. (1) T-die 42" (1070 mm). (1) Farrel Bridge 3 roller calendar, 42.5" (1080 details
|
More Info
Width (in.): 55
Manufacturer: Barmag
Roll Diameter (in.):
Model:
14006001
Used-Barmag Coex Sheet Film Line with 2 extruders for A-B-A layer structure. (1) 3.54" (90 mm) with 176 hp/132 kW DAC motor and (1) 1.18" (30 mm) 60 hp/45 kW AC motor. New melt pump for B layer and hydraulic screen changer, Cloeren feed block with insert for A-B-A layer structure and 55" (1400 mm) polishing stack with AC drives for each roll, with encoder, details
|
|
|
More Info
Width (in.): 60
Manufacturer: DAVIS STANDARD
Roll Diameter (in.): 24
Model:
41715001
Used- Davis Standard Multi-Layer Sheet/ Thermoforming Line Consisting Of: (1) Davis Standard model 60IN60TPIH, 6" screw diameter, 30:1 L/D ratio, electrically heated, water cooled, 500 hp DC drive thru 17.2:1 gearbox ratio. (2) Davis Standard model 100MM35F, 3.9" screw diameter, 30:1 L/D ratio, electrically heated, water cooled, 125 hp DC drive thru 17.44:1 details
|
More Info
Width (in.): 12
Manufacturer: WELEX
Roll Diameter (in.): 8
Model: 250
41690001
Used- Welex Sheet Line Consisting Of: (1) Welex 2-1/2'' single screw extruder, model 250 24:1AC, serial #1864 8-80, approximate 24 to 1 L/D ratio, 3 zone non-vented barrel, electrically heated, air cooled. Water cooled feed throat with magnet. Approximate 44-3/4'' centerline height. Driven by a 40 hp, 500 volt, 1750 rpm DC motor thru a gearbox, ratio 9.3 details
|
More Info
Width (in.): 53
Manufacturer: WELEX
Roll Diameter (in.): 18
Model: 450-30
41682001
Used- Welex 53'' Wide Sheet Line Consisting Of: (1) Welex 4-1/2'' single screw extruder, model 450-30, serial #385, approximate 30:1 L/D ratio, approximate 8 zone side vented barrel, electrically heated, air cooled. Water cooled feed throat, no hopper. Approximate 57'' centerline height. Driven by a 200 hp, 500 volt, 1750/200 rpm DC motor thru a Welex details
|
More Info
Width (in.): 75
Manufacturer: HPM
Roll Diameter (in.): 18
Model: 4.5TMIII
41343001
Used- HPM Sheet Line Consisting Of: (1) HPM 4-1/2'' Single Screw Extruder, Model 4.5TMIII, serial# 82-210. Approximately 38 to 1 L/D ratio. Electrically heated, water cooled 6 zone dual side vented barrel, with pump, and heat exchanger, no holding tank. Approximate 34-1/2'' center line height. Water cooled feed throat with hopper. Driven by a 200 hp, details
|
|
|
More Info
Width (in.): 54
Manufacturer: HPM
Roll Diameter (in.): 24x54
Model: SHEETMASTER III
41157002
Used- HPM Sheet Take Off System consisting of: (1) HPM Sheetmaster III 3 Roll Sheet Stack, rated speed range 20 feet per minute maximum, 71'' track centerline. (3) 23.587'' diameter x 54'' wide cored rolls, (1) chrome plated, (2) matte. Each roll driven by a 5 hp motor thru a reducer, ratio 450 to 1, hydraulic roll adjustment with power pack and contol details
|
More Info
Width (in.): 85
Manufacturer: Davis Standard
Roll Diameter (in.):
Model:
41008001
Used 2-1/2" x 32:1 DEAC Vented MAC Extruder with 75 hp DC non-regenerative 2-1/2" x 32:1 mixing screw. 2-1/2" valved adapters with hydraulic screen changer, 52" coathanger die for 43" coated web 3-way movement coextrusion carriage, temperature control/power panel, 3-roll etrusion laminator. details
|
More Info
Width (in.): 2.75
Manufacturer: Kuhne
Roll Diameter (in.): 25.4
Model:
40362002
Used-Kuhne Sheet Extrusion Line with an output of 374 lbs (170 kgs)/hour consisting of: (1) Morette Plastic System mixing/feeding system; (1) Kuhne single screw extruder, 30 mm, 30:1 L/D, electrically heated, air cooled; (1) melt pump; (1) EDI Ultra Flex H75 650 mm; (1) 25.4" (650 mm) sheet roll stack; (1) pulling unit; (1) winding unit station; (1) Kurtx details
|
More Info
Width (in.): 62.99
Manufacturer: Union
Roll Diameter (in.):
Model:
10665007
Used-1600mm wide Union sheet coextrusion line. 120mm, 60mm single screw extruders, melt pump, 1500mm die, 1600 x 450mm polishing stack, guillotine, 2000. 120mm Union single screw extruder. Electrically heated, fan cooled barrel. 35D vented. 210 kW DC motor with drive. Union 30 hp AC melt pump. Year 2000. 60mm Kuhne coextruder, vented, 33:1D. 1600mm wide details
|
More Info
Width (in.): 57.08
Manufacturer: Omipa/Repiquet
Roll Diameter (in.):
Model:
10665005
Used-1450mm wide Omipa/Repiquet sheet extrusion line, 120mm Omipa extruder, melt pump, Omipa 1450mm die, Repiquet 5 roll stack, haul off, shear, 1991. 120mm Omipa extruder OM120 1990, serial 90177, 33D vented, 141 kW DC motor, electrically heated fan cooled, 7 zone barrel. 21 zone temperature control panel, DC thyristor control panel. 120mm lantern slide details
|
More Info
Width (in.): 66.9
Manufacturer: Kuhne
Roll Diameter (in.):
Model:
10665004
Used-1700mm wide Kuhne coextrusion sheet line, comprising 105mm extruder, 30mm coextruder, 1650mm wide Vergrugg en die, 1700 x 400mm roll stack, haul off, 1988. 105mm Kuhne single screw extruder 33D. Fan cooled barrel, vented. 150 kW DC motor (2 sets of drive pulleys to adjust torque range). Electrically heated fan cooled barrel, spare grooved feed zone sleeve, details
|
More Info
Width (in.): 68.9
Manufacturer: Battenfeld
Roll Diameter (in.):
Model:
10665003
Used-1750mm wide Battenfeld sheet line, 115mm single screw extruder, 70/70 gear pump, 1750 x 400mm 3 roll stack, haul off, guillotine, 1991. 115mm diameter single screw Battenfeld extruder. 30D plugged vent, 7 zone electrically heated fan cooled barrel, serial A14747, 19:1 gearbox ratio, 214 kW DC motor. 115mm hydraulically operated lantern slide screen details
|
More Info
Width (in.):
Manufacturer:
Roll Diameter (in.):
Model:
10665001
Used-890 mm wide Welex Coextrusion sheet line. 90 mm main extruder, 50 mm coextruder, 890 x 300 mm rolls, pump group, haul off, 2 station winder, 1990. 90 mm Welex single screw extruder, 30D vented. Water cooled barrel. 100 hp DC motor and drive. Hydraulic screw changer with power pack and accumulator. Maag model 56/3T gear pump (2000) with DC motor and details
|
More Info
Width (in.): 54
Manufacturer: BATTENFELD GLOUCESTE
Roll Diameter (in.): 16
Model: 244-001
40508004
Used- Battenfeld Gloucester Laminating Line consisting of: (1) Battenfeld Gloucester 4 1/2'' single screw extruder, model 244-001, 24 to 1 L/D ratio, electrically heated, water cooled side vented 5 zone barrel. Water cooled feed throat with hopper. Approximate 43'' centerline height. Driven by a 150 hp, 500 volt, 1750/2000 rpm DC motor thru a gearbox, ratio details
|
More Info
Width (in.): 54
Manufacturer: BATTENFELD GLOUCESTE
Roll Diameter (in.): 16
Model: 244-001
40508005
Used- Battenfeld Gloucester Laminating Line consisting of: (1) Battenfeld Gloucester 4 1/2'' single screw extruder, model 244-001, 24 to 1 L/D ratio, electrically heated, water cooled side vented 5 zone barrel. Water cooled feed throat with hopper. Approximate 43'' centerline height. Driven by a 150 hp, 500 volt, 1750/2000 rpm DC motor thru a gearbox, ratio details
|
More Info
Width (in.): 62
Manufacturer: BATTENFELD GLOUCESTE
Roll Diameter (in.): 1
Model: 244.001
40508006
Used- Battenfeld Gloucester Tandem Foam Extrusion Line consisting of: (1) 4.5" Battenfled Gloucester extruder, model 244.001, 36:1 L/D, electrically heated, water cooled, jacketed feed section with 150 hp DC motor with SCR controller, serial #244.29812.01. (1) 4.5" Beringer hydraulic screen changer. (1) 6" Battenfeld Gloucester extruder, model 266.001, details
|
|
|
More Info
Width (in.): 54
Manufacturer: GLOUCESTER
Roll Diameter (in.):
Model: 267-001
40578001
Used- Gloucester 54'' wide foam line consisting of: (1) Glouster 6'' single screw extruder, model 267-001, approximately 30 to 1 L/D ratio. Electrically heated, water cooled barrel, approximate 42'' center line height. Driven by a 200 hp, 500 volt, 1750 rpm DC motor thru a reducer, ratio 41.83 to 1. Includes a die clamp. (1) Glouster 4 1/2'' single screw details
|
More Info
Width (in.): 47
Manufacturer: OMV
Roll Diameter (in.): 20x47
Model:
40550001
Used- OMV 3 Roll Sheet Stack. (3) Approximately 20'' diameter x 47'' wide chrome plated cored rolls with (2) approximately 20'' diameter x 47'' wide chrome plated cooling rolls, all driven by a 3 kw, 320 volt, DC motor with reducers. Cooling rolls chain driven off of center roll. (1) Sussex Instruments mechanical thickness gauge with controls, serial# details
|
More Info
Width (in.): 84
Manufacturer: PTI
Roll Diameter (in.): 40x84
Model:
40505002
Used- PTI Trident Series Multi Layer Sheet Extrusion System consisting of: (1) Used 6" PTI Trident Series extruder, model 6000, 28:1 L/D electrically heated, air cooled, 7 barrel zones, jacketed feed section, 21.75:1 gearbox ratio, 400 hp, 1791/2686 rpm AC motor, with Dynisco hydraulic screen changer, Gravimetric material loader and 40 hp gear pump. (1) details
|
More Info
Width (in.): 84
Manufacturer: PTI
Roll Diameter (in.):
Model:
40453001
Used- PTI (2004) Multi-Layer Sheet Extrusion Line including the following: A) (1) Used PTI model 6000 Trident series 6", 28:1 extruder having a 7-zone electrically heated, air cooled barrel at approximatley a 94" centerline height. Gearbox is a Flender model SZNS-390, has reduction ratio of 21.756:1, has a service rating of 400 hp and a catalog rating of 701 details
|
More Info
Width (in.): 84
Manufacturer: PTI
Roll Diameter (in.):
Model:
40453002
Used- PTI Multi-Layer Sheet Extrusion Line including the following: A) (1) Used PTI model 6000 Trident series 6", 28:1 extruder having a 7 zone electrically heated, air cooled barrel at an approximate 94" centerline height. Gearbox is a Flender model SZNS-390, has reduction ratio of 21.756:1, has a service rating of 400 hp and a catalog rating of 701 details
|
|
|
More Info
Width (in.): 47.2
Manufacturer: Union
Roll Diameter (in.): Union
Model:
523936
USED: Union 47.2" (1200mm) sheet extrusion line consisting of: (1) 3.54" (90mm) Union single screw extruder, electrically heated, power 50 kW, fan cooled barrel, 30D vented, driven by a 61 kW motor with drive; (1) sieve change, diameter 2 x 4.7" (120mm), hydraulic unit, heating power 6 kW; (1) Union 3 stack calander, roll diameter 11.8" - 13.8" - 11.8" (300-350-300mm), details
|
More Info
Width (in.): 1.5
Manufacturer: Davis Standard
Roll Diameter (in.): Davis
Model:
523797
USED: Davis Standard stretch tape line for lab or pilot plant use. Complete with (1) used Davis Standard 1.5" thermatic extruder, 24:1 L/D, vented and plugged, electrically heated, air cooled, complete with control panel, 4 barrel zones, 1 adapter zone, 3 die zones, 10 hp variable speed drive. (1) Stainless steel quench tank. (1) 8" x 33" MPM 3 roll Godet details
|
More Info
Width (in.): 17.5
Manufacturer: Battenfeld
Roll Diameter (in.): 10
Model:
89095
USED: Battenfeld 17.5" wide sheet/cast film line consisting of: (1) Battenfeld 60 mm (2.3") single screw extruder, model 1-60-30DV, serial #89-7782-62, approximate 30:1 L/D ratio, 5 zone non-vented barrel, electrically heated, air cooled. Driven by a 52 kw (70 hp), 460 volt DC motor thru a gearbox with control panel. (1) Battenfeld 45 mm (1.7") single screw details
|
More Info
Width (in.): 50
Manufacturer: Processing Technolog
Roll Diameter (in.): Proces
Model: 5024
523574
USED: Processing Technologies Inc model 5024 3 roll down stack. Manufactured 2/2000. 24" diameter x 50" wide lower 2 chrome rolls, upper roll is 12" x 50". All chrome rolls cored for cooling. Rolls are hydraulically operated and powered by a 7.5 hp DC motor via silent chain drive, Control Techniques Mentor II DC drives for stack and pull roll station, details
|
More Info
Width (in.): 34
Manufacturer: Cincinnati Milacron
Roll Diameter (in.): Cincin
Model:
523575
USED: Cincinnati Milacron 3 roll stack/laminator. Two cored for cooling chrome rolls 17.75" diameter x 34" wide; two aluminum guide rolls, one 17.74" diameter x 31" wide and one 8" diameter x 31" wide. Chrome rolls are pneumatically operated and are powered by a 5 hp, 1750 rpm, 500 volt DC motor thru a Koellmann 18.131:1 gearbox via silent chain drive, details
|
More Info
Width (in.): 33
Manufacturer:
Roll Diameter (in.):
Model:
523560
USED: Three roll sheet stack. (3) rolls with 33" face x 12" diameter cored rolls, with hydraulic gap adjustment, single row, chain driven with 3 hp 230/460 volt motor with variable frequency drive, 5" diameter x 34" face rubber nip roll assembly with hydraulic gap adjustment and 2 hp 230/460 volt motor with variable frequency drive. details
|
More Info
Width (in.): 51
Manufacturer: Gefran
Roll Diameter (in.): Gefran
Model: TN75
523526
USED: Gefran sheet extrusion line. (1) Extruder Tr1-75/35, screw diameter 2.95" (75mm), degassing, 380V/50 hz/3 ph; (1) die head 51"(1300mm); (1) 3 roll calender type CL1, width 51" (1300mm), diameter 13.4" (340mm), max opening 2.76" (70mm); (1) haul off TRL 51" x 7.9" (1300mm x 200mm), opening max 3.9" (100mm); cutting unit TLS 1300; (1) lifting platform; details
|
More Info
Width (in.): 60
Manufacturer: Amut
Roll Diameter (in.): Amut
Model: DS145
523504
USED: Amut sheet line. (1) Amut DS co-rotate extruder 5.7" (145mm) 20D, screen changer, melt pump, degassing, motor 212 hp (156 kw), 400 volt/3 phase, 50 hz. (1) Piovan gravimetric dosing system, 3 components. (1) Die head 33" (840mm), flexible lips; (1) die head 48" (1220mm) flexible lips; (1) die head 60" (1525mm) flexible lips; (1) new spare gear unit; details
|
More Info
Width (in.): 60
Manufacturer: Amut
Roll Diameter (in.): Amut
Model: DS145
523505
USED: Amut sheet line. (1) Amut DS co-rotate extruder 5.7" (145mm) 20D, screen changer, melt pump, degassing, motor 212 hp (156 kw), 400 volt/3 phase, 50 hz. (1) Piovan gravimetric dosing system, 3 components. (1) Die head 33" (840mm), flexible lips; (1) die head 48" (1220mm) flexible lips; (1) die head 60" (1525mm) flexible lips; (1) new spare gear unit; details
|
More Info
Width (in.): 12
Manufacturer: Berstorff
Roll Diameter (in.): Bersto
Model: ZE25
523507
USED: Berstorff twin screw extruder line. (1) Berstorff extruder 1" (25mm), type ZE25 40D, Feller control panels included. (2) Berstorff feeding units, ZSFE-DDSR20. (1) Busch vacuum pump; (1) die head 150 x 0 to 4 cubic mm; (1) 3 roll calendar, temperature control by oil. (3) Brabender scale 2xDDW-P3-DDSW20N-15, 1xDDW-P3-DDSR20N, Brabender Congrav L/M-2 details
|
More Info
Width (in.): 33
Manufacturer:
Roll Diameter (in.):
Model:
523006
USED: Three roll sheet stack. (3) rolls with 33" face x 12" diameter cored rolls, with hydraulic gap adjustment, single row, chain driven with 3 hp, 230/460 volt motor with VFD, 5" diameter x 34" face rubber nip roll assembly with hydraulic gap adjustment and 2 hp, 230/460 volt motor with variable frequency drive. details
|
|
|
More Info
Width (in.): 60
Manufacturer: Breyer
Roll Diameter (in.): Breyer
Model: MONO EXTRUDER
522861
USED: Breyer 60" (1560mm) sheet line for 1.5 mm sheet thickness x 1500 mm with a capacity of 808 lbs/400 kgs per hour consisting of: (1) feeding/blending system; (1) Breyer single screw extruder, type Mono, 30:1 L/D, 4.6" (120 mm) diameter screw, electrically heated, air cooled, vented; (1) Maag Extrex 56/56 gear pump; (1) Breyer 60" (1560) sheet die head details
|
|
|
More Info
Width (in.): 41
Manufacturer: Welex
Roll Diameter (in.): 18
Model:
86659
USED: Welex Sheet Extrusion Downstream Stack. 3 rolls measure 18" diameter x 41" face width. Two chrome, one ceramic. Rolls are chain driven by a 5 hp DC drive. Pneumatically operated roll closure. Unit includes heat exchanger pumps for roll temperature control. Rubber pull rolls are unitized to frame. Unit does not include the standard rubber pull rolls. details
|
More Info
Width (in.): 78
Manufacturer: Omipa
Roll Diameter (in.): Omipa
Model:
84979
USED: 2000mm Omipa Coex Sheet Line. 120mm extruder, gear pump, coextruder, coex block, fastgap die, 2000mm Omipa 3 roll inclined stack, conveyor, haul off.
* 120mm Omipa model OM120 single screw extruder. Vented. Fan cooled, electrically heated. Serial no 88102, 160kw dc motor with Thyristor drive. Hydraulic lantern slide screen changer. OM 65 gear pump, details
|
|
|
More Info
Width (in.): 66
Manufacturer: Davis Standard
Roll Diameter (in.): 20.8
Model:
82270
USED: Davis Standard sheet take-off unit consisting of (3) 66" face by nominal 20.8" diameter rolls, mounted in a vertical arrangement for an upstack operation. Unit includes (7) total rolls: (3) chrome rolls having a 2 to 4 RMS finish, (2) matte finish rolls, (1) ceramic roll and (1) silicone rubber roll. Rolls are hydraulically actuated. (1) 3 zone details
|
More Info
Width (in.): 52
Manufacturer: APV
Roll Diameter (in.):
Model:
521330
USED: APV Sterling extrusion line for the production of PP filament for woven sacks/bags. Line includes (1) APV Sterling 4.5" extruder, 30:1 L/D ratio single screw extruder, 200 hp main drive motor; (1) Polynetics 4 component blender, hoppers loaded by Conair model DL 12 vacuum receivers, 3 augers are driven by 1/8 hp variable speedmotors. System discharges details
|
More Info
Width (in.): 54
Manufacturer: Davis Standard
Roll Diameter (in.): 3.5
Model:
520034
USED: Davis Standard 75mm extruder, 54" Johnson sheet line as follows: (1) Used 75mm Davis Standard extruder, electrically heated, water cooled, 30:1 L/D vented barrel, 17.26:1 gearbox ratio, 100 hp DC motor, skid mounted with controls and SCR controller, 500# per hour, on stand, new 1990. (1) Used 3.5" Beringer hydraulic screen changer with power pack. details
|
More Info
Width (in.): 34
Manufacturer:
Roll Diameter (in.): 3.5
Model:
70503
USED: Panel sheet line consisting of: 1 panel chiller, 34" wide x 64" long; (48) 2" wide x 1/2" thick cored cooling bars, vertically adjustable, 1/4 hp motor; (1) 24" wide x 75" long belt puller, vertically adjustable, 2 hp DC gearmotor; (1) 8" wide x rubber pull rolls, 7" diameter, vertically adjustable, 1-1/2 hp gearmotor, ratio 60:1, has speed controls; details
|
|
|