11453076
Used-Mitsubishi 550 Metric Ton Injection Molder, Model 550MMIII-80. 1400 x 940 mm or 940 x 1400 mm mold size, 950 x 950 mm tie bar clearance, 2110 CM3 injection capacity, 380-800 mm mold thickness, 80 oz capacity, with hydraulic core pull, Hitachi H-300 PLC controls. New July 1996. OAD approximately 28' long x 8' x 8' high. Approximately 53,000#. details
|
40747011
Used- Cincinnati Milacron Vista Toggle Horizontal Injection Molder, 85 ton, Model VST85-5CE. Clamp force 85 ton, clamp stroke 11", maximum daylight 24". Mold height maximum/minimum 13"/4.9". Platen size 22" x 19.7". Tie rod diameter 2.36", distance between rods 14.2" x 11.8". Ejector stroke maximum 2.8", ejector force 4 tons. Injection unit shot size 5 ounce, details
|
40748001
Used- Arburg Allrounder injection mold machine, model 320D-210-750, 83 ton clamping pressure. Platen size 19.3" x 19.3". Distance between tie bars 12.6". Max daylight 24.6". Max stroke of hydraulic ejector 5.9". Mold opening stroke adjustable to 14.75". .98" diameter screw, 24:1 L/D. Unit includes free standing control panel. Built 1987.
details
|
|
|
|
|
|
|
523953
USED: Cincinnati Milacron 300 ton, model VT300-34, injection molding machine, 34 oz. Manufactured 1994. Platen size 36.8" x 36.2". Tie bar spacing 25.2" x 24.6". Max daylight 48". Clamp stroke 22.8". Ejector tonnage 8.3". Injection stroke 10.2". Max/min mold height 25.2"/7.9". Motor 50 hp, Camac VEL control, CP, RI. details
|
|
|
523959
USED: Toshiba 310 ton, model ISG310V10-19AT, injection molding machine, 30 oz. Manufactured 1997. Platen dimensions 36.6" x 35.4".Tie bar spacing 32.2" x 24". Max daylight 41.7". Min daylight 11.8". Clamp stroke 30". Ejector stroke 4.9". Equipped with Injectvisor V10 control, CP, air confirmation, includes Yushin Netliner Robot VNII-250S. details
|
|
|
|
|
|
|
|
|
523919
USED: 300 ton, 32 oz, HPM injection molding machine, model T300-32.New 1997. 41,505 hours. Platen size 36.5" x 36.8". Distance betweentie bars 24.5" x 24.5". Clamp stroke 22.0". Maximum daylight 44.0".Maximum mold thickness 22.0". Minimum mold thickness 8.0". Maximummold size 24.4" x 36.5". Ejector stroke 5.0". Dimensions (L x W x H)28'6" x 7'6" x 8'. details
|
523920
USED: 250 ton, 29 oz, Cincinnati injection molding machine, modelVH250-29, type Vista Hydraulic. New 1995. 63,949 hours. Platen size30.70" x 30.70". Distance between tie bars 22.05" x 22.05". Maximumdaylight 39.10". Minimum closed daylight 3.35". Clamp stroke 29.50".Ejector stroke (max) 5.00". Equipped with Camac 486 control, hydraulicknockouts, 29 details
|
523921
USED: 300 ton, 30 oz, Van Dorn injection molding machine, model300RS30F-HT. Year 1995. Platen size 39" x 36.50". Distance betweentie bars 24" x 24". Tie rod diameter 4.25". Open daylight 46". Minmold thickness 8". Max mold thickness 24". Equipped with P-2500control, core pull, 30 oz injection unit, clamp tonnage control,premium filtration package, feed throat details
|
|
|
523509
USED: 700 Ton, 80 ounce, Van Dorn injection molding machine, model700HRS-80F-LP. New 1989. Wide platen. Platen size 62" x 53.50".Distance between tie bars 45" x 36.50". Clamp stroke 44". Maximumopen daylight 72.75". Minimum mold thickness 16". Dimensions (1 piece)32.5" long x 8' wide x 9.8" high. Weight 98,000 lbs. Equipped withwide platen option, CRT-B details
|
523510
USED: 700 Ton, 80 ounce, Van Dorn injection molding machine, model700HRS-80F-LP. New 1993. Platen size 62" x 52.50". Distance betweentie bars 45" x 36". Clamp stroke 44". Maximum open daylight 72.75".Minimum mold thickness 16". Equipped with Siemens EL control, wideplaten option, 80 ounce injection unit, hydraulic knockouts, core pullsequence ABCD, core details
|
523511
USED: 1000 Ton, 140 ounce, Cincinnati Milacron injection moldingmachine, model VL1000-140. New 1994. Platen size 63" x 63". Distancebetween tie bars 44" x 44". Maximum mold space 63" x 44". Minimummold thickness 14.6". Clamp stroke 48". Maximum daylight 92.50".Parts drop clearance 24". HP motor 155. Equipped with Camac VELcontrol, 140 ounce injection unit, details
|
|
|
|
|
|
|
85923
USED: JSW 30.86 ton toggle injection molding machine, model J28SC. Platen size approximately 14-7/8" x 13-3/8". Distance between 1-5/8" diameter tie bars approximately 9.45" left to right x 7.87" top to bottom. Max daylight 17.13", mold thickness min/max 6.3"/9.06". Clamp stroke 8.07". Approximate .98" diameter screw, 1.65 cubic inch shot capacity. Includes details
|
|
|
|
|
522117
USED: Mitsubishi injection molding machine, 720 ton, model 720MGW-160.New 1991. Platen size 60.00" x 60.00". Distance between tie bars42.00" x 42.00". Maximum daylight 79.90". Minimum mold thickness 17.70". Equipped with Mitsubishi MAC IV process control, hydraulicknockouts, core pull, 160 oz injection unit, loader with hopper. Unit is offered as is, details
|
522118
USED: 950 ton, 160 oz Mitsubishi injection molding machine, model950MG. Mfg 1993. Platen size 60.00" x 60.00". Distance between tiebars 41.73" x 41.73". Clamp stroke 63". Maximum daylight 88.58".Ejector stroke 7.90". Screw diameter 3.54". Injection pressure25,890 psi. Main motor 150 hp. Equipped with Mitsubishi MAC IV, corepull, 160 oz injection unit, details
|
|
|
83027
USED: Cincinnati 110 ton toggle injection molding machine, model VT110-10. Platen size 24.8" x 22.8". Distance between 2.8" diameter tie bars 14.2" left to right x 16.1" top to bottom. Max daylight 27.6", mold height min/max 5.9"/15.7". Clamp stroke 11.8", clamp speed typical dry cycle time 1.53 seconds. 1.772" diameter screw, 20:1 L/D ratio, approximate 10 details
|
|
|
521672
USED: 150 ton, 4.9 oz Autojector shuttle press, model HCS-150. New1995. Mold clamping force 150 ton. Platen size 16" x 20". Maximumclamp stroke 14". Mold height min/max 10" to 14". Max daylight 24".Maximum ejection stroke 4". Injection stroke 7". Parting line height6" - 11.75" adj. Barrel heat 4 zone. Motor .25 hp. Equipped with turbotough control, hydraulic details
|
521674
USED: 150 ton, 5 oz Autojector shuttle press, model HCS-150. New 1995.Mold clamping force 150 ton. Platen size 16" x 20". Maximum clampstroke 14". Mold height min/max 10" to 14". Max daylight 24". Maximumejection stroke 4". Injection stroke 7". Parting line height 6"-11.75"adj. Barrel heat 4 zone. Motor 25 hp. Equipped with turbo touchcontrol, hydraulic details
|
82447
USED: Boy hydraulic injection mold machine, model 80T2. 80 ton clamping pressure. Platen size 24" x 22". Distance between 2-1/2" diameter tie bars 14". Max daylight 26.77". Max stroke of hydraulic ejector 5.11". Mold opening stroke adjustable to 16.92". Approximately 1" diameter screw. Unit includes Dipronic control panel. details
|
82448
USED: Boy hydraulic injection mold machine, model 50T2. 50 ton clamping pressure. Platen size 19-1/2" x 19-1/2". Distance between 2" diameter tie bars 12". Max daylight 23". Max stroke of hydraulic ejector 3.14". Mold opening stroke adjustable to 13.77". Approximate 1" diameter screw. Unit includes Dipronic control panel. details
|
81593
USED: Arburg Allrounder injection mold machine, model 270M-250-75. 25 ton clamping pressure. Platen size 15.74" x 15.74". Distance between tie bars 10.62". Max daylight 21.65". Max stroke of hydraulic ejector 4.92". Mold opening stroke adjustable to 12.79". Approximately 1" diameter screw. Unit includes free standing digital control panel. details
|
521066
USED: Van Dorn model 275-HP-20 "H-Series" 275 ton x 20 oz horizontal plastic injection molding machine, 1996. Hydraulic clamp, computerized enclosed base, 10-1/4" screw stroke, Bijur one shot lubrication system, filters, floor cushion pads, knockouts, Van Dorn Pathfinder model 3000 computerized control console, hydraulics, hopper and AEC loader, magnetic details
|
|
|
78975
USED: Mitsubishi injection molding machine, model 70/30MSS. 30 ton clamping pressure, 20:1 L/D, platen size 15" (380mm) wide x 15" (380mm) high, distance between 1-3/4" tie bars 10-1/2" left to right, 10-1/2" top to bottom, 2.4 oz (70cc) shot capacity, 16" daylight, 1" screw feed, 21" long, driven by 14.9 hp, 3/50/60/200/220 volts, 1430/1730 rpm. Unit has digital details
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
66137
USED: CLF (Chuan Lih Fa) injection molder, model CLF-280-T, new 1990. 309 ton clamp force, 36.42" X 34.64" platen size, 24.41" X 22.83" distance between tie bars, 22.83" clamp stroke, 48.42" max daylight opening, 6.10" ejector stroke. Equipped with CLF micro-computer control panel with CRT, hydraulic knockouts, core pull sequence, 40 oz injection unit, double details
|
|
|