41592001
Used-3.5" DAVIS STANDARD MODEL 3.5MV-350 SINGLE SCREW EXTRUDER. NEW 2000. SERIAL #I3131. DRIVEN BY 60 HP AC MOTOR 3/60/460V WITH AC VARIABLE SPEED INVERTER. HAS ELECTRICALLY HEATED,5 ZONED AIR COOLED BARREL, 30/1 L/D. INCLUDES TEMPERATURE CONTROL PANEL WITH 5 BARREL ZONES AND 3 DIE ZONES, EUROTHERM 2208 INSTRUMENTS. GEAR BOX SO#70151, RATED 158HP, details
|
41592002
Used-DAVIS STANDARD MODEL 3.5MV-350 SINGLE SCREW EXTRUDER. NEW 2000. SERIAL #I3137. DRIVEN BY 60 HP AC MOTOR 3/60/460V WITH AC VARIABLE SPEED INVERTER. HAS ELECTRICALLY HEATED,5 ZONED AIR COOLED BARREL, 30/1 L/D. INCLUDES TEMPERATURE CONTROL PANEL WITH 5 BARREL ZONES AND 3 DIE ZONES, EUROTHERM 2208 INSTRUMENTS. GEAR BOX SO#70151, RATED 158HP, SERVICE FACTOR details
|
41592003
Used-3.5" DAVIS STANDARD MODEL 3.5MV-350 SINGLE SCREW EXTRUDER. NEW 12/2000. SERIAL #16467. DRIVEN BY 60 HP AC MOTOR 3/60/460V WITH AC VARIABLE SPEED INVERTER. HAS ELECTRICALLY HEATED,5 ZONED AIR COOLED BARREL, 30/1 L/D. INCLUDES TEMPERATURE CONTROL PANEL WITH 5 BARREL ZONES AND 3 DIE ZONES, EUROTHERM 2208 INSTRUMENTS. GEAR BOX SO#71076 RATED 158HP, details
|
41592004
Used-3.5" NRM/DS 24/1 L/D SINGLE SCREW EXTRUDER. AIR COOLED BARREL. NEW 1995. EXTRUDER MODEL PACEMAKER IIII 35PM IV, TEMPERATURE CONTROL PANEL (4) BARREL ZONES AND (3) DIE ZONES HAS EUROTHERM MODEL 808 CONTROLLERS. SERIAL #19230. ORDER #53054. MACHINE HAS 75 HP DC MOTOR AND RELIANCE SCR. GEAR BOX RATED 1.25 SERVICE FACTOR, 15.25: 1 GEAR RATIO. UNIT HAS details
|
10288010
Used-3/4" Brabender Lab Extruder, 24:1 L/D. Electrically heated barrel, water cooled, 3 barrel zones, venged barrel, jacketed feed throat, stainless steel feed hopper. Equipped with control cabinet which includes Honeywell programmable controller, GE adjustable speed drive, disconnect and motor starter. Unit is mounted on cabinet with casters. Drive reported details
|
|
|
|
|
11453109
Used-1.25" Davis Standard Extruder, model DS-12-HM. 24:1 L/D, electrically heated, air cooled, vented and plugged, jacketed feed section, 5 hp DC motor with SCR controller, 17.9:1 gearbox ratio, 3 barrel zones, 2 die zones on unitized base with control panel, new 1993. details
|
11453108
Used-1.5" Davis Standard Extruder, model 15IN20. 24:1 L/D, electrically heated, air cooled, jacketed feed section, 15 hp DC motor, 4 barrel, 1 clamp, 3 die zones, 16.53:1 gearbox ratio, 1.25 service factor, with control panel and SCR controller. details
|
11453107
Used-1.5" Davis Standard Extruder, model DS-15S. 24:1 L/D, electrically heated, air cooled, jacketed feed with hopper, 15 hp DC motor, 15:1 gearbox ratio, 100 rpm screw, 4 zone, pedestal mounted, new 1985. details
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
41466007
Used- Davis Standard-NRM 3-1/2" Single Screw Extruder, Model PM IV. 24 to 1 L/D Ratio. Electrically heated, water cooled 4 zone non-vented barrel with a pump, tank, and heat exchanger. Water cooled feed throat, no hopper. Driven by a 75hp, 500 volt, 1750/2100 rpm motor thru a gearbox, ratio 15.21 to 1. approximate 42'' centerline height. Includes a control details
|
41466008
Used- Davis Standard-NRM 3-1/2" Single Screw Extruder, Model PM IV. 24 to 1 L/D Ratio. Electrically heated, water cooled 4 zone non-vented barrel with a pump, tank, and heat exchanger. Water cooled feed throat, no hopper. Driven by a 75hp, 500 volt, 1750/2100 rpm motor thru a gearbox, ratio 15.21 to 1. approximate 42'' centerline height. Includes a control details
|
41466001
Used- Davis Standard 3-1/2" Single Screw Extruder, Model Mark V. 30 to 1 L/D Ratio. Electrically heated, air cooled 5 zone non-vented barrel. Water cooled feed throat with magnet, no hopper. Driven by a 125hp, 3/60/90/460 volt, 1790/2685 rpm inverter motor thru a gearbox, ratio 17.39 to 1. Approximate 42‘’ centerline height. Includes a die clamp, a details
|
41343002
Used- PTI 3.5'' Trident Series Single Screw Extruder, Model 3500. Approximate 24 to 1 L/D ratio. 4 zone electrically heated, air cooled non-vented barrel. Water cooled feed throat, with hopper. Approximate 42'' centerline height. Driven by a 125 hp DC motor thru a gearbox, ratio 17.65 to 1. Includes a die clamp, 15 KVA transformer, and a side mounted control details
|
41305001
Used- Davis Standard 2 1/2" Single Screw Extruder, Model 25MK5, Type DSPA. 24 to 1 L/D Ratio. Electrically heated, air cooled 4 zone side-vented barrel with vacuum pump. Water cooled feed throat with hopper. Driven by a 40hp, 3/60/460 volt, 1770 rpm motor thru a gearbox, ratio 17.26 to 1. 42 1/4'' centerline height. Includes a control panel with Eurotherm details
|
|
|
40883001
Used- Akron 2 1/2'' Single Screw Extruder, Model PAK250, approximately 24 to 1 L/D ratio. Electrically heated, air cooled 4 zone non-vented barrel. Water cooled feed throat, with hopper. Approximately 46'' centerline height. Driven by a 40hp DC motor with a gearbox. Includes a control panel with Eurotherm 2208 temperature controllers (1 missing), and a Reliance Flex details
|
40883002
Used- Akron 2 1/2'' Single Screw Extruder, Model PAK250, approximately 24 to 1 L/D ratio. Electrically heated, air cooled 4 zone non-vented barrel. Water cooled feed throat, with hopper. Approximately 46'' centerline height. Driven by a 40hp, 500 volt, 1750/2100 rpm DC motor with a gearbox, ratio 14 to 1. Includes a control panel with Eurotherm 808 temperature details
|
40883003
Used- Welex 2 1/2'' Single Screw Extruder, Model 250, approximately 24 to 1 L/D ratio. Electrically heated, air cooled 3 zone non-vented barrel. Water cooled feed throat, with hopper. Approximately 45'' centerline height. Driven by a 40hp, 500 volt, 1750 rpm DC motor with a gearbox, ratio 9.3 to 1. Includes a control panel with Eurotherm, and Watlow temperature details
|
41180001
Used- Hartig 6'' Single Screw Extruder. Model 60/100M24, 24:1 L/D Ratio. 7 zone barrel, electrically heated, water cooled with a 1 1/2 HP pump and heat exchanger, no tank. Water cooled feed with hopper. Approximate 54 1/2" centerline height. Driven by a 400 HP, 500 Volt, 1750/1900 RPM DC motor thru gearbox, ratio 12.47:1. , Has a transformer, and a control details
|
10665011
Used-1040mm (3.4’) Welex coextrusion sheet line, with 115mm (4.5’’) with 30:1 L/D single screw Welex extruder, model 450, 30:1 RHS.V, 7 zone water cooled barrel. Vented, Reitschele high quality vacuum pump and liquor trap, 189 kW (252 hp) motor, 170rpm max screw speed with 115mm Welex hydraulic lantern slide screen changer with power pack mode. Static details
|
|
|
40865002
Used-Welex 3 1/2'' single screw extruder, model 35VA, serial #372-436383, approximate 30:1 L/D ratio, 5 zone non-vented barrel, electrically heated, water cooled with closed loop system with pump, tank, and heat exchanger(missing). Approximate 48'' centerline height. Driven by an approximat 150 hp DC motor thru a gearbox, ratio 17.59 to 1. (1) Die clamp details
|
|
|
|
|
41020001
Used- Davis Standard 3'' Single Screw Extruder, Model 75MM75MV MFG 2002, Approximate 30:1 L/D ratio. Electrically heated, air cooled, non-vented 6 zone barrel. Water cooled feed throat with magnet, no hopper. Approximate 43 3/4" centerline height. Driven by a 60 hp, 3/60/230/460 volt, 1782 rpm motor with a gearbox ratio 17.26:1. Includes a manual screen details
|
40913001
Used- HPM 2" Single Screw Extruder, Model 2.0TMC24. Approximate 24:1 L/D ratio. Electrically heated, air cooled, 3 zone non-vented barrel. Water cooled feed throat with magnet, no hopper. Driven by a 20 hp DC motor thru a gearbox. Approximate 43" centerline height. Includes a control panel with Eurotherm controllers, and a Contraves drive. Mounted on details
|
40913002
Used- Welex 2" Single Screw Extruder, Model 20024:1RH. No screw. Electrically heated, air cooled 3 zone non-vented barrel, missing 2 blowers. Water cooled feed throat, no hopper. Driven by a 20 hp, 500 volt, 1750 rpm DC motor thru a gearbox, ratio 10:1. Approximate 43 1/2" centerline height. Includes an incomplete control panel. Mounted on a common base. details
|
40913003
Used- NRM 2 1/2" Single Screw Extruder, Model 2.5-24:1 PMIVRH/ACNVTD. Approximate 24:1 L/D ratio. Eletrically heated, air cooled 4 zone non-vented barrel. Water cooled feed throat, no hopper. Approximate 43" centerline height. Driven by a 40 hp, 500 volt, 1750-2100 rpm DC thru a gearbox, ratio 15.23:1. Includes a control panel with Eurotherm 808 controllers, details
|
40913004
Used- Welex 2" Single Screw Extruder, Model 20024:1 R.H. Approximate 24:1 L/D ratio. Electrically heated, air cooled 3 zone non-vented barrel. Water cooled feed throat, no hopper. Driven by a 20 hp, 240 volt, 1750-2300 rpm DC motor thru a gearbox, ratio 10:1. Approximate 46" centerline height. Includes a control panel with Eurotherm controls. Mounted details
|
40913005
Used- Akron 2 1/2" Single Screw Extruder Model PAK 250. Approximate 24:1 L/D ratio. Electrically heated, air cooled 4 zone non-vented barrel. Water cooled feed throat, no hopper. Driven by a 40 hp, 500 volt, 1750 rpm DC motor thru a gearbox, ratio 13.95:1. Approximate 44 1/2" centerline height. Includes a control panel with Eurotherm controllers. Mounted details
|
40913006
Used- Cosmo 2 1/4" Single Screw Extruder. Approximate 26:1 L/D ratio. Electrically heated, air cooled 4 zone non-vented barrel. Water cooled feed throat, no hopper. Driven by a 20 hp, 440 volt, 2810 rpm DC motor thru a reducer. Approximate 42" centerline. Includes a control panel with Ultra-Therm controllers and (2) Klockner Moeller Typact panels. details
|
40913007
Used- Akron 3 1/2" Single Screw Extruder, Model PAK350, Approximately 24:1 L/D Ratio. Electrically heated, air cooled 5 zone non-vented barrel. Water cooled feed throat, no hopper. Driven by a 75 hp, 300 volt, 1750 rpm DC motor thru a gearbox, ratio 13.95:1. Approximate 42" centerline height. Includes a control panel with Gefran controllers. Mounted on a details
|
40913008
Used- Akron 3 1/2" Single Screw Extruder, Model PAK350. Approximate 24:1 L/D ratio. Electrically heated, air cooled 5 zone non-vented barrel. Water cooled feed throat, no hopper. Driven by a 75 hp, 300 volt, 1750 rpm DC motor thru a gearbox, ratio 13.95:1. Approximate 38" centerline height. Includes a control panel with controllers. Mounted on a common details
|
40913009
Used- Welex 2" Single Screw Extruder, Model 2.00AC. Approximate 24:1 L/D ratio. Electrically heated, air cooled 3 zone non-vented barrel. Water cooled feed throat with magnet, no hopper. Driven by a 20 hp, 500 volt, 1750 rpm DC motor thru a gearbox, ratio 10:1. Approximate 42" centerline height. Includes a control panel with controllers, (1) missing. details
|
40913010
Used- Akron 3 1/2" Single Screw Extruder, Model PAK350, Approximate 24:1 L/D Ratio. Electrically heated, air cooled 5 zone non-vented barrel. Water cooled feed throat, no hopper. Driven by a 75 hp, 300 volt, 1750 rpm DC motor thru a gearbox, ratio 13.95:1. Approximate 42" centerline height. Includes a control panel with Eurotherm controllers, (1) missing, details
|
40913011
Used- Akron 3 1/2" Single Screw Extruder, Model PAK350. Approximate 24:1 L/D ratio. Electrically heated, air cooled 5 zone air non-vented barrel. Water cooled feed throat with magnet, no hopper. Driven by a 75 hp, 300 volt, 1750 rpm DC motor thru a gearbox, ratio 13.95:1. Approximate 40" centerline height. Includes a control panel with Eurotherm controllers, details
|
|
|
|
|
40913015
Used- Cosmo 2 1/2" Single Screw Extruder. Approximately 30:1 L/D ratio. Electrically heated, air cooled 4 zone non-vented barrel. Water cooled feed throat with magnet, no hopper. Driven by a 4/40 hp, 73/410 volt, 250/2500 rpm motor thru a gearbox. Approximately 42 1/2" centerline height. Includes a die clamp and a control panel with Static Control Systems details
|
40913016
Used- HPM 2" Single Screw Extruder, Model 2.0TMC24. Approximate 24:1 L/D ratio. Electrically heated, air cooled, 3 zone non-vented barrel. Water cooled feed throat with magnet and hopper. Driven by a 20 hp, 500 volt, 1150 rpm DC motor thru a gearbox, ratio 9.4586:1. Approximate 47 1/2" centerline height. Includes a control panel with Eurotherm controllers details
|
|
|
40913018
Used- Single Screw Extruder, approximate 2'' diameter screw, approximate 24 to 1 L/D ratio. Electrically heated, air cooled 3 zone non-vented barrel. Water cooled feed throat with hopper. Driven by a 20 hp, 500 volt, 2500 rpm DC motor thru a gearbox. Approximate 49" centerline height. Mounted on a common base. No controls.
details
|
|
|
|
|
40733009
Used- Sterling Extruder Corp 1 1/2'' single screw extruder. Approximately 24 to 1 L/D ratio. Electrically heated, water cooled 4 zone non-vented barrel, no water system. Water cooled feed throat with hopper. Approximate 47'' centerline height. Driven by a 10 hp, 500 volt, 1750 rpm DC motor thru a gearbox, ratio 26.40 to 1. Includes a control panel with Barber-Coleman details
|
40726001
Used- Akron 3 1/2'' Single Screw Extruder, Model PAK350, approximately 24 to 1 L/D ratio. Electrically heated, air cooled 5 zone non-vented barrel. Water cooled feed throat, no hopper. Approximate 45'' centerline height. Driven by a 75 hp, 500 volt, 1750/2100 rpm DC motor with a Koellmann gearbox, ratio 13.95 to 1. Includes a die clamp, a control panel with details
|
|
|
|
|
40570001
Used- PTI 5'' Trident Series Single Screw Extruder, Model 5000. Approximate 28 to 1 L/D ratio. 5 zone electrically heated, air cooled non-vented barrel. Water cooled feed throat, no hopper. Approximate 52'' centerline height. Driven by a 300 hp, 3/60/460 volt, 1192/1785 rpm motor thru a gearbox, ratio 17.111 to 1, 300 hp rating, catalog rating 482 hp, details
|
40570002
Used-PTI 2.5'' Trident Series single screw extruder, model 2500. Approximate 32 to 1 L/D ratio. 5 zone electrically heated, air cooled non-vented barrel. Water cooled feed throat, no hopper. Approximate 88'' centerline height. Driven by a 50 hp, 3/60-90/460 volt, 1780/2670 rpm motor thru a gearbox, ratio 17.533 to 1, 75 hp rating, catalog rating 150 hp. details
|
40570003
Used-PTI 2.5'' Trident Series single screw extruder, model 2500. Approximate 32 to 1 L/D ratio. 5 zone electrically heated, air cooled non-vented barrel. Water cooled feed throat, no hopper. Approximate 82'' centerline height. Driven by a 50 hp, 3/60-90/460 volt, 1780/2670 rpm motor thru a gearbox, ratio 17.533 to 1, 75 hp rating, catalog rating 150 hp. details
|
40408001
Used- PTI model 3500 3.5", 30:1 extruder having a 5 zone electrically heated, air cooled barrel at an approximate 42" centerline height. Gearbox is direct driven by a 125 hp AC motor in a tuck under manner. Unitized temperature control panel with solid state controllers. Offered less inverter. Includes 220 KVA, 460 volt isolation transformer for drive details
|
40350001
Used-NRM 2.5" single screw extruder, model PM IV. 2.5" screw diameter, 24:1 L/D ratio, electrically heated, air cooled, non-vented barrel. Gearbox ratio 15.23:1, 1750 rpm, 1.25 SF, rated 56 hp. Unit driven by a 50 hp DC motor thru a Reliance DC drive and Fenner digital controller. 460 volt, 94 amp. Reported hours used 13,384. Reported manufactured 1990. details
|
40158032
Used- Betol 1.9'' (50mm) Single Screw Extruder, Model BC50, approximate 24 to 1 L/D ratio. Electrically heated, air cooled 4 zone non-vented barrel. Water cooled feed throat with a hopper. Driven by an 18 hp (13.4 kw), 3/460/1560 rpm motor thru a reducer, ratio 14 to 1. Includes a control panel with Eurotherm digital controllers, and a Reliance Flex-Pak details
|
40158034
Used- Akron 1 3/4'' Single Screw Extruder, Model M-PAK175, approximately 24 to 1 L/D ratio. Electrically heated, air cooled 3 zone non-vented barrel. Water cooled feed throat with a lump breaker, no hopper. Approximately 42'' centerline height. Driven by a 15 hp AC motor with a gearbox. Includes a control panel with Barber Coleman temperature controllers (2 details
|
40158016
Used- Akron 1 3/4'' single screw extruder, model M-PAK175, approximately 24 to 1 L/D ratio. Electrically heated, air cooled, 3 zone non-vented barrel. Water cooled feed throat with a lump breaker, no hopper. Approximately 42'' centerline height. Driven by a 15 hp, 640 volt, 1750 rpm DC motor with a gearbox, ratio 14 to 1. Includes a free standing control panel details
|
40158017
Used- Akron 1 3/4'' Single Screw Extruder, Model M-PAK175, approximately 24 to 1 L/D ratio. Electrically heated, air cooled 3 zone non-vented barrel. Water cooled feed throat with a lump breaker, no hopper. Approximately 42'' centerline height. Driven by a 15 hp, AC motor with a gearbox, ratio 14 to 1. Includes a control panel with Barber Coleman temperature details
|
|
|
|
|
|
|
|
|
|
|
90541
USED: Davis Standard extruder, model 75MM25, type DSPA. 75 mm screw diameter, approximate 44:1 L/D ratio. 152 1/2" from back of feed throat to end of barrel. Electrically heated, 10 zone barrel air cooling. 5" long x 3 1/4" wide feed opening. Approximate 42 1/2" centerline height. Driven by a 42.4 kW, 480 volt, 1985 rpm DC motor with gearbox ratio 17.26:1. details
|
|
|
|
|
|
|
89311
Used- Royal Machine 1.25" Pedestal Mounted Single Screw Extruder, Model 252.25. Approximate 12:1 L/D ratio, electrically heated, air cooled single zone non-vented barrel. Water cooled feed throat with hopper. Driven by a 3 hp, 180 volt, 1750/2050 rpm DC motor thru a reducer, ratio 50:1. Includes a control panel with controllers. Mounted on a common base details
|
89312
Used- Royal Machine 1.25" Parts Machine Pedestal Mounted Single Screw Extruder, Model 253. Approximate 24:1 L/D ratio, electrically heated, air cooled 3 zone non-vented barrel. Water cooled feed throat no hopper. Requires screw, and motor. Includes a control panel with controllers and a brushless 1000 drive. Motorized vertical adjustment. Mounted on a common details
|
89322
Used- Becz Machine 1.25" Pedestal Mounted Single Screw Extruder, Model 252.25. Approximate 12:1 L/D ratio. Electrically heated, air cooled single zone non-vented barrel. Water cooled feed throat with hopper. Driven by a 3 hp, 180 volt, 1750/2050 rpm DC motor thru a reducer, ratio 50:1. Includes a control panel with controllers. Mounted on a common base details
|
|
|
|
|
89085
USED: Royal 10" single screw dump extruder. 6:1 L/D ratio, cored screw, (2) zone jacketed barrel. 11" x 12" jacketed feed throat with chute. Approximate 42" centerline height, swing away 1-1/2" diameter die. Driven by a 150 hp, 3/60/575 volt, 1783 rpm motor thru a Royle 3A gearbox. Includes a transformer, variable AC drive panel. details
|
|
|
|
|
87997
Used- Deltaplast Machinery 4.5" Single Screw Extruder, Model D130:450:34. Approximately 34:1 L/D ratio. Electrically heated, water cooled 8 zone, side vented barrel. Closed loop system with (2) pumps, (2) tanks and (2) heat exchangers. Water cooled feed throat, no hopper. Driven by a 250 hp, 500 volt, 1750/2000 rpm DC motor thru a reducer. Gearbox ratio details
|
|
|
|
|
|
|
523064
USED: Single screw Collin lab extruder, type 30x25D. Screw diameter 1.18" (30mm); electrically heated 1200W, air cooled, zone 1 and 2 water cooled, pressure of water cooling system 7-58 psi (0.5-4 bar). Motor max 3000 rpm, 480V by 60 cycle, extension up to 30D. Length 63" (1600mm), width 20" (500mm), height 59" (1500mm). No control panel. details
|
523021
USED: Single screw Collin lab extruder, type 30x25D. Screw diameter 1.18" (30mm); electrically heated 1200W, air cooled, zone 1 and 2 water cooled, pressure of water cooling system 7-58 psi (0.5-4 bar). Motor max 3000 rpm, 400V by 50 cycle, extension up to 30D. Length 63" (1600mm), width 20" (500mm), height 59" (1500mm). No control panel. details
|
523022
USED: Single screw Collin lab extruder, type 30x25D. Screw diameter 1.18" (30mm); electrically heated 1200W, air cooled, zone 1 and 2 water cooled, pressure of water cooling system 7-58 psi (0.5-4 bar). Motor max 3000 rpm, 400V by 50 cycle, extension up to 30D. Length 63" (1600mm), width 20" (500mm), height 59" (1500mm). No control panel. details
|
523005
USED: NRM 6" extruder, 32:1 L/D ratio having an electrically heated,liquid cooled (closed loop) barrel at 42-1/2" centerline height butcurrently mounted on movable base supplying total 84" centerlineheight. Feed throat is center oblong measuring 7" wide x 13" long.Gearbox has a reduction ratio of 17.16:1 and is direct driven by a 400 hp DC motor with SCR controller. details
|
87249
Used- Plasti Program 1.3" single screw extruder, model RS35, approximately 24:1 L/D ratio. Electrically heated, air cooled 3 zone non-vented barrel. Water cooled feed with hopper, approximately 41" centerline height. Driven by a 10 hp, 500 volt DC motor with gearbox. Control panel with Watlow controllers. Built 1988. details
|
|
|
87251
Used- Plasti Program 1.3" single screw extruder, model RS35, approximately 24:1 L/D ratio. Electrically heated, air cooled 3 zone non-vented barrel. Water cooled feed with hopper, approximately 41" centerline height. Driven by a 10 hp, 500 volt DC motor with gearbox. Control panel with Watlow controllers and a Baldor DC drive. Built 1988. details
|
|
|
|
|